Tyco Electronics 58591-1 User manual
Instruction Sheet
PRO-CRIMPER* III Hand
Crimping Tool Assembly 58591-1 408-4354
L C B
1
of 5
E
2009 Tyco Electronics Corporation, Harrisburg, PA
All International Rights Reserved
TE logo and Tyco Electronics are trademarks.
*Trademark. ther products, logos, and company names used are the property of their respective owners.
T LING ASSISTANCE CENTER 1-800-722-1111
PR DUCT INF RMATI N1-800-522-6752 This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at
www.tycoelectronics.com
11 JUN 09 Rev A
with Die Assembly 58591-2
PROPER USE GUIDELINES
CumulativeTraumaDisorderscanresultfromtheprolongeduseof manuallypoweredhandtools.Handtoolsareintendedforoccasionaluseandlowvolume
applications. A wide selection of powered application equipment for extended-use, production operations is available.
Stationary Jaw
Back of Tool
(Wire Side)
Pivot Pin
PR -CRIMPER III Hand
Crimping Tool Frame
354940-1 (408-9930)
Stationary Handle
Moving Handle
Ratchet Adjustment Wheel
Moving Jaw
Die Assembly
Front of Tool
(Locator Side)
Locator Assembly
(Supplied with
Die Assembly)
The PR -CRIMPER III Hand Crimping Tool Assembly is a Commercial"
grade tool and is designed primarily for field installation, repair, maintenance
work, or prototyping in industrial, commercial, or institutional applications.
Product crimped with this tool will meet the crimp height requirement for hand
tools in the appropriate 114 series specification, but may not comply with other
feature parameters of the specification. Tyco Electronics offers a variety of
tools to satisfy your performance requirements. For additional information,
contact the Tooling Assistance Center at 1-800-722-1111.
TE Die
TE Locator
Contact
ire
TE Di
e
Assembly
TE L
oca
t
or
Assembly
{
C
on
t
ac
t
Family
}
Size
(mm2)Insul Dia
(mm [in.]) Strip Length
(mm [in.])
Micro 0.75
58591-2 58515-3 Power
Quadlok
1.0 3.40
[.134]
3.81 - 4.60
[.150
-
.181]
Quadlok
Seal 0.5
[
.
134]
[
.
150
.
181]
{
Supplied with die assembly, also available separately.
}
Contact the Tooling Assistance Center or Product
Information Center (see below) for specific contact part
numbers.
Figure 1
1. INTRODUCTION
PRO–CRIMPER III Hand Crimping Tool Assembly
58591–1 consists of Die Assembly 58591–2 and
PRO–CRIMPER III Hand Crimping Tool Frame
354940–1. The die assembly consists of crimping
dies and a locator assembly.
Read these instructions thoroughly before crimping
any contacts.
Reasons for revision are listed in Section 11,
REVISION SUMMARY.
Dimensions on this sheet are in millimeters [with
inch equivalents provided in brackets]. Figures
and illustrations are for identification only and are
not drawn to scale.
2. DESCRIPTION
(Figures 1 and 2)
The tool features a tool frame with a stationary jaw
and handle, a moving jaw, a moving handle, and an
adjustable ratchet that ensures full contact crimping.
The tool frame holds a die assembly with three
crimping sections.
NOTE
i
408-4354
PRO-CRIMPER III H nd Crimping Tool Assembly 58591-1
Rev
A2
f5 Tyc Electr nics C rp rati n
Figure 2
Nut L cat r
Assembly T l Frame
Die Retaining Pins
Die Retaining Screws
Chamfer
Insulati n Anvil
Wire Anvil
Offset
Wire Crimper
Chamfer Insulati n
Crimper
The die assembly features a wire anvil, an insulation
anvil, a wire crimper, and an insulation crimper.
Attached to the outside of the frame is a locator
assembly, which contains a locator, a spring retainer,
and a contact support.
Die retaining pins and die retaining screws are used
to position and secure the dies in the tool frame. A
nut is used on the upper die retaining screw to hold
the locator assembly in place.
3. INSTALLATION AND REMOVAL OF DIE SET
AND LOCATOR ASSEMBLY
(Figure 2)
1. Open the tool handles and remove the two die
retaining screws from the tool jaws.
2. Place the wire anvil and insulation anvil so that
their chamfered sides and their marked surfaces
face outward, when mounted in the moving jaw of
the tool frame.
3. Insert the two die retaining pins.
4. Insert the short die retaining screw through the
jaw and through both anvil dies, and tighten the
screw just enough to hold the dies in place. Do
not
tighten the screw completely at this time.
5. Place the wire crimper and insulation crimper so
that their chamfered sides and their marked
surfaces face outward, when mounted in the
stationary jaw of the tool frame.
6. Insert the two die retaining pins.
7. Insert the long die retaining screw through the
jaw and through both crimper dies, and tighten the
screw just enough to hold the dies in place. Do
not
tighten the screw completely at this time.
8. Carefully close the tool handles, making sure
that the anvils and crimpers align properly.
Continue closing the tool handles until the ratchet
in the tool frame has engaged sufficiently to hold
the anvils and crimpers in place, then tighten both
die retaining screws.
9. Place the locator assembly over the end of the
long screw, and position the locator assembly
against the side of the tool jaw.
10. Place the nut onto the end of the long screw
and tighten the nut enough to hold the locator
assembly in place, while still allowing the locator to
slide up and down.
11. To disassemble, close the tool handles until the
ratchet releases, remove the nut, the locator
assembly, the two die retaining screws, and the
four die retaining pins, and slide the anvils and
crimpers out of the tool jaws.
4. CONTACT SUPPORT ADJUSTMENT
(Figure 3)
The contact support is preset prior to shipment,
but minor adjustment may be necessary.
NOTE
i
408-4354
PRO-CRIMPER III Hand Cri ping Tool Asse bly 58591-1
3
of 5Rev
A
Tyco Elec ronics Corpora ion
1. Make a sample crimp and determine if the
contact is straight, bending upward, or bending
downward.
2. If adjustment is required, loosen the screw that
holds the contact support onto the locator
assembly.
The ratchet has detents that create aud ble cl cks
as the tool handles are closed.
3. Place a contact with wire into the proper nest
and close the tool handles until the ratchet reaches
the sixth click, or until the contact support touches
the contact.
4. Slightly loosen the nut that holds the locator
assembly onto the tool frame.
5. Move the contact support as required to
eliminate the bending of the contact.
6. Tighten the nut and close the handles until the
ratchet releases.
7. Remove and inspect the contact.
8. Make another sample crimp. If the contact is
straight, tighten the contact support screw. If the
contact is still being bent during crimping, repeat
the adjustment procedure.
5. CRIMPING PROCEDURE
Th s tool s prov ded w th a cr mp adjustment
feature. Int ally, the cr mp he ght should be
ver f ed as spec f ed n F gure 4. Refer to Sect on
6, CRIMP HEIGHT INSPECTION, and Sect on 7,
RATCHET ADJUSTMENT, to ver fy cr mp he ght
before us ng the tool to cr mp des red contacts
and w re s zes.
Refer to the table in Figure 1 and select wire of the
specified size and insulation diameter. Strip the wire
to the length indicated in Figure 1, taking care not to
nick or cut wire strands. Select an applicable contact
and identify the appropriate crimp section according
to the wire size markings on the tool. Refer to
Figure 3 and proceed as follows:
1. Hold the tool so that the back (wire side) is
facing you. Squeeze tool handles together and
allow them to open fully.
2. Holding the contact by the mating end, insert the
contact — insulation barrel first — through the front
of the tool and into the appropriate crimp section.
3. Position the contact so that the mating end of
the contact is on the locator side of the tool, and so
that the open “U” of the wire and insulation barrels
must face the top of the tool. Place the contact up
into the nest so that the movable locator drops into
the slot in the contact. Refer to Figure 3. Butt the
front end of the wire barrel against the movable
locator.
Make sure that both s des of the nsulat on barrel
are started evenly nto the cr mp ng sect on. Do
NOT attempt to cr mp an mproperly pos t oned
contact.
Figure 3
Adjus men
Screw for
Con ac
Suppor
Con ac
Suppor Loca or
Back of Tool
(Wire Side)
Wire
Con ac
(Typ)
Loca or in
Wire S op Slo Wire
Inser ed
o S op
S rip
Leng h
Wire
Seal
Wire
Seal
NOTE
i
NOTE
i
CAUTION
!
408-4354
PRO-CRIMPER III Hand Crimping Tool Assembly 58591-1
Rev
A4
of 5 Tyco Electronics Corporation
4. Hold the contact in position and squeeze the
tool handles together until ratchet engages
sufficiently to hold the contact in position. Do NOT
deform insulation barrel or wire barrel.
5. Insert stripped wire, with wire seal, into contact
insulation and wire barrels until it is butted against
the wire stop, as shown in Figure 3.
6. Holding the wire in place, squeeze tool handles
together until ratchet releases. Allow tool handles
to open and remove crimped contact.
The crimped contact may stick in the crimping
area, but the contact can be easily removed by
pushing downward on the top of the locator (see
Figure 3).
7. Check the contact’s crimp height as described in
Section 6, CRIMP HEIGHT INSPECTION. If
necessary, adjust the crimp height as described in
Section 7, CRIMP HEIGHT ADJUSTMENT.
6. CRIMP HEIGHT IN PECTION
Crimp height inspection is performed through the use
of a micrometer with a modified anvil, commonly
referred to as a crimp–height comparator. Tyco
Electronics does not manufacture or market
crimp–height comparators. Detailed information on
obtaining and using crimp–height comparators can be
found in instruction sheet 408–7424.
Proceed as follows:
1. Refer to Figure 4 and select a wire (maximum
size) for each crimp section listed.
2. Refer to Section 5, CRIMPING PROCEDURE,
and crimp the contact(s) accordingly.
3. Using a crimp height comparator, measure the
wire barrel crimp height as shown in Figure 4. If the
crimp height conforms to that shown in the table,
the tool is considered dimensionally correct. If not,
the tool must be adjusted. Refer to Section 7,
RATCHET (Crimp Height) ADJUSTMENT.
7. RATCHET (Crimp Height) ADJU TMENT
(Figure 5)
1. Remove the lockscrew from the ratchet
adjustment wheel.
2. With a screwdriver, adjust the ratchet wheel
from the locator side of the tool.
Position Point
on Center of
Wire Barrel
Opposite
Seam
A"
Mo ifie Anvil
WIRE IZE CRIMP ECTION CRIMP HEIGHT
DIM.
(
A
)
AND
mm2(MAX) (WIRE IZE MARKING)
()
TOLERANCE
+.05 [+.002]
0.75 0.75 1.27
[.0500]
1.0 1.0 1.36
[.0535]
0.5 0.5 1.18
[.0465]
Figure 4
3. Observe the ratchet adjustment wheel. If a
tighter crimp is required, rotate the adjustment
wheel COUNTERCLOCKWISE to a
higher–numbered setting. If a looser crimp is
required, rotate the adjustment wheel
CLOCKWISE to a lower–numbered setting.
Figure 5
Screw river
Ratchet
A justment
Wheel
Lockscrew
(Typ)
NOTE
i
408-4354
PRO-CRIMPER III Hand Cr mp ng Tool Assembly 58591-1
5
of 5Rev
A
Tyco Electronics Corporation
4. Replace the lockscrew.
5. Make a sample crimp and measure the crimp
height. If the dimension is acceptable, replace and
secure the lockscrew. If the dimension is
unacceptable, continue to adjust the ratchet, and
again measure a sample crimp.
8. MAINTENANCE
Ensure that the tool and dies are clean by wiping
them with a clean, soft cloth. Remove any debris with
a clean, soft brush. Do not use objects that could
damage the tool. When not in use, keep handles
closed to prevent objects from becoming lodged in
the crimping dies, and store in a clean, dry area.
9. VISUAL INSPECTION
The crimping dies should be inspected on a regular
basis to ensure that they have not become worn or
damaged. Inspect the crimp sections for flattened,
chipped, worn, or broken areas. If damage or
abnormal wear is evident, the tool must be replaced.
See Section 10, REPLACEMENT.
10. REPLACEMENT
Customer–replaceable parts are shown in Figure 1.
Available separately, PRO–CRIMPER III Hand
Crimping Tool Repair Kit 679221–1 includes a
replacement nut and a variety of pins, rings, screws,
and springs.
If the dies are damaged or worn excessively, they
must be replaced.
Order the repair kit and replaceable parts through
your Tyco Electronics representative, or call
1–800–526–5142, or send a facsimile of your
purchase order to 1–717–986–7605, or write to:
CUSTOMER SERVICE (38–35)
TYCO ELECTRONICS
PO BOX 3608
HARRISBURG PA 17105–3608
11.REVISION SUMMARY
Since the previous release of this instruction sheet,
the following items have changed:
S
PRO–CRIMPER II hand tool became
PRO–CRIMPER III hand tool;
S
TE logo was applied; and
S
The format was updated to the current
corporate requirements.
This manual suits for next models
2
Table of contents
Other Tyco Electronics Crimping Tools manuals
Tyco Electronics
Tyco Electronics PRO CRIMPER III User manual
Tyco Electronics
Tyco Electronics 90430-1 User manual
Tyco Electronics
Tyco Electronics PRO-CRIMPER III User manual
Tyco Electronics
Tyco Electronics PRO-CRIMPER III User manual
Tyco Electronics
Tyco Electronics PRO- CRIMPER III User manual
Tyco Electronics
Tyco Electronics PRO-CRIMPER III User manual
Tyco Electronics
Tyco Electronics 2063195-1 User manual
Tyco Electronics
Tyco Electronics 58569-1 User manual
Tyco Electronics
Tyco Electronics PRO-CRIMPER II User manual
Tyco Electronics
Tyco Electronics AMP 91907 User manual
Tyco Electronics
Tyco Electronics ERGOCRIMP 2-1579021-9 User manual
Tyco Electronics
Tyco Electronics 69156-1 User manual
Tyco Electronics
Tyco Electronics PRO-CRIMPER III User manual
Tyco Electronics
Tyco Electronics 1490749-1 User manual
Tyco Electronics
Tyco Electronics PRO-CRIMPER III User manual
Tyco Electronics
Tyco Electronics 696675-1 User manual
Tyco Electronics
Tyco Electronics 1213850-1 User manual
Tyco Electronics
Tyco Electronics PRO-CRIMPER III User manual
Tyco Electronics
Tyco Electronics PRO-CRIMPER III User manual
Tyco Electronics
Tyco Electronics PRO-CRIMPER III User manual
Popular Crimping Tools manuals by other brands
Textron
Textron ESG105L instruction manual
Emerson
Emerson Klauke ES 20RMCCFB manual
Continental Refrigerator
Continental Refrigerator PC150HD quick start guide
TE Connectivity
TE Connectivity ERGOCRIMP 1-1579001-3 instruction sheet
Emerson
Emerson Klauke ES 105CFB manual
TE Connectivity
TE Connectivity 539 726-2 instruction sheet