tronical Tune User manual
MANUAL
V 2.12
MANUAL
V 2.12
WE ARE SPINNING HEADS!
WWW.TRONICAL-COMPONENTS.COM
2
TRONICAL TUNE - INDEX
TRONICAL TUNE OVERVIEW 3
TRONICAL TUNE INSERT/REPLACE BATTERY 45
TUNE CONTROLLER 6
GETTING STARTED INSTALL THE SYSTEM TO THE GUITAR 78
STRING YOUR GUITAR 912
STRING UP AND DOWN MODE 13
HOW TO TUNE / ADDITIONAL INFO 14
PERFORMANCE SPECIFICATION 15
START TO TUNE MULTISTRING / SINGLESTRING TUNING 1617
SWITCH BETWEEN BANKS 18
EXAMPLE 19
BANK OVERVIEW 20
FUNCTION MENU FUNCTION OVERVIEW 21
CUSTOM TUNING | SAVING 2223
REFERENCE TUNING 24
FIRMWARE VERSION 25
BATTERY LEVEL 26
CONFIGURATION MENU
OVERVIEW 27
ACCURACY MODE 28
ROBOHEAD DELAY 29
RESET MODE 30
ROBOHEAD SPEED 31
INTERFERENCE LEVEL 32
SYSTEM CONFIGURATION EXPERT MENU 3337
CHARGING THE BATTERY 38
LEGAL INFORMATION 39
WWW.TRONICAL-COMPONENTS.COM
3
6 ROBOHEADS
WITH NEW SURFACE LOCKING MECHANISM
TRONICAL TUNE OVERVIEW
BAT
e B G D AE
MENU
INTEGRATED LEDDISPLAY
6 STRING LEDS, 1 MENU LED, 1 CHARGE LEVEL LED
BATTERY
EXCHANGEABLE, RECHARGEABLE
3.7 VOLTS, LIPOLYMER, APPROX. 300 TUNINGS
TUNE CONTROLLER
UP, DOWN, LEFT, RIGHT, ENTER
AVAILABLE SPARE PARTS
LiPoBATTERY
CHARGER WITH WALLPLUG
ROBOHEADS
TUNING CONTROLLER WITH
MOUNTING BOARD
WRENCH, LOCK NUTS &
RING WASHERS
ON/OFF/BACK
BLACK TUNING CONTROLLER
BLACK MOUNTING BOARD WITH ROBOHEAD GUIDANCE
WWW.TRONICAL-COMPONENTS.COM
4
BAT
e B G D A E
MENU
BAT
e B G D A E
MENU
BAT
e B G D A E
MENU
BAT
e B G D A E
MENU
INSERT BATTERY
TRONICAL TUNE
ATTENTION: USE CAUTION WHEN INSTALLING
THE BATTERY. ENSURE YOU PAY ATTENTION
TO THE SLOTTED DESIGN TO GUARANTEE
PROPPER ORIENTATION. SLIDE IN THE BATTERY
WITH THE TIP SIDE ONLY. DO NOT APPLY ANY
FORCE AS YOU MAY CAUSE DAMAGE TO THE
ELECTRONICS.
!
WWW.TRONICAL-COMPONENTS.COM
5
PRESS ON THE BATTERY
TO RELEASE. PULL OUT THE BATTERY
BAT
e B G D A E
MENU
BAT
e B G D A E
MENU
1 2
REPLACE BATTERY
TRONICAL TUNE
ATTENTION: USE CAUTION WHEN INSTALLING THE BATTERY. ENSURE YOU PAY ATTENTION TO THE SLOTTED DESIGN
TO GUARANTEE PROPPER ORIENTATION. SLIDE IN THE BATTERY WITH THE TIP SIDE ONLY. DO NOT APPLY ANY FORCE
AS YOU MAY CAUSE DAMAGE TO THE ELECTRONICS.
!
WWW.TRONICAL-COMPONENTS.COM
6
EXPLANATION TUNE CONTROLLER
: FREQUENCY MEASUREMENT IN PROGRESS
: INTERFERENCE BETWEEN LOWER AND HIGHER STRINGS
: STRING IN TUNE
: BATTERY FULLY CHARGED
: RESPECTIVE ROBOHEAD IS IN MOVEMENT
: FREQUENCY OUT OF PITCH WINDOW
: BATTERY IS EMPTY
: FUNCTION MENU
: ACOUSTIC GUITAR
BLINKING MENU LED
: SYSTEM CONFIGURATION
: ELECTRIC GUITAR
PUSH AND HOLD THE ”OFF-BUTTON“
TO SWITCH OFF THE SYSTEM.
i
MUTE LOWER STRINGS THAT ARE IN TUNE
AND STRUM HIGHER STRINGS AGAIN.
i
BAT
e B G D A E
MENU
RIGHT
ON/OFF/BACK
ENTER / OK
UP
DOWN
LEFT
WWW.TRONICAL-COMPONENTS.COM
7WWW.TRONICAL-COMPONENTS.COM
INSTALL THE SYSTEM TO THE GUITAR
GETTING STARTED
NOTE: DO NOT USE ANY TOOLS TO FIX THE LOCK NUT
AND DO NOT OVER TIGHTEN AS YOU MAY. USE A 1 CENT COIN TO TIGHTEN
THE LOCKNUT, OTHERWISE YOU MAY DAMAGE THE GEAR WHEELS!!
USE ONLY SUPPLIED WRENCH OR TORQUE WRENCH TO
TIGHTEN THE HEX NUTS MAX. 1NM TORQUE
IT IS RECOMMENDEDTO USE A CONTACT CLEANING SOLUTION BEFORE INSTALLING
THE ROBOHEADS TO THE PCB BOARD ANDTO ALSO NOT OVER TIGHTEN THE HEX NUTS
BEFORE ENSURING ALL CONTACTS ARE MAKING A GOOD CONNECTION.
USE CAUTION WHEN INSTALLING BATTERY AND ENSURE YOU PAY ATTENTION TOTHE
SLOTTED DESIGN TO GUARANTEE PROPER ORIENTATION!!!
WWW.TRONICAL-COMPONENTS.COM
8
INSTALL THE SYSTEM TO THE GUITAR
GETTING STARTED
AT FIRST REMOVE ALL ORIGINAL
HEADSTOCKPARTS OF YOUR GUITAR.
TAKE THE ROBOHEADS OUT OFF THE
CONTACTING PCB.
PLACE THE CONTACTING PCB ON THE NECK
OF THE GUITAR, THE BATTERY COMPARTMENT
HAS TO FACE TOWARDS THE TOP OF
THE HEADSTOCK.
MAKE SURE THAT ALL PCB DRILL HOLES ARE
IN ALIGNMENT WITH THE NECKS TUNER HOLES.
PUT THE ROBOHEADS THROUGH THE
RESPECTIVE HOLES. MOUNT THE HEXNUTS.
USE THE WRENCH WHICH COMES
WITH THE SET TO SCREW TIGHT THE HEX
NUTS OF THE ROBOHEADS.
NOW TRONICAL TUNE IS READY TO
STRING UP YOUR GUITAR.
1
4
2
5
3
6
WWW.TRONICAL-COMPONENTS.COM
9
STRING YOUR GUITAR
GETTING STARTED
MAX. RECCOMENDED STRING GAUGES: .013 .017 .026 .035 .045 .056 THIRTEEN TO FIFTYSIXES
NOTE: HIGHER STRING GAUGES MAY CAUSE DAMAGE TO THE TUNERS!
PLEASE NOTE THE BASS SIDE ROBOHEADS TURN IN THE OPPOSITE DIRECTION FROM USUAL.
THEY NOW TURN CLOCKWISE TO SHARPEN AND COUNTERCLOCKWISE TO FLATTEN.
WWW.TRONICAL-COMPONENTS.COM
10
HOW TO USE THE STRING SHAFT WITH
SURFACE LOCKING MECHANISM
GETTING STARTED
LOCK NUT: YOU NEED THE LOCK NUT TO TIGHTEN THE STRING.
STRING SHAFT: THE STRING SHAFT WINDS THE STRING.
STRING RECESS: THE STRING RECESS GUIDES THE STRING.
HEX NUT: USE THE WRENCH WHICH COMES WITH THE SET TO
TIGHTEN THE HEX NUTS OF THE ROBOHEADS. LOCK NUT
STRING RECESS
STRING SHAFT
HEX NUT
1
1
2
3
4
3
4
3
USE ONLY SUPPLIED WRENCH OR TORQUE WRENCH TO
TIGHTEN THE HEX NUTS MAX. 1NM TORQUE
NOTE: DO NOT USE ANY TOOLS TO FIX THE LOCK NUT
AND DO NOT OVER TIGHTEN AS YOU MAY. USE A 1 CENT COIN TO TIGHTEN
THE LOCKNUT, OTHERWISE YOU MAY DAMAGE THE GEAR WHEELS!!
Table of contents
