Triton 9600 User manual
-
21405 B Street
Long Beach, MS 39560
Phone: (228) 575-3100
Fax: (228) 575-3101
© 2014 Triton. All Rights Reserved. TRITON logo is a registered trademark of
Triton Systems of Delaware, LLC
2
………………………………………..Page 3
…………………………………...Page 4
…………………………………….Page 7
………..…………………………………………...Page 12
or higher installed in the Memory mod-
ule.
If your machine contains a Quad Port Module, you will also need a
Memory Expansion Module with 1 MB or higher of space.
--
These items are included in the iLAN external Ethernet opon kit.
3
This secon describes how to install the External Ethernet Box and associated hardware for 9600 and 9700
model ATMs. The table below lists the accessories and other components included in the External Ethernet
Option kit.
-
1
1
1
- 2
- 2
4
4
Unlock and open the control panel. Turn the power supply switch to the OFF (0) posion.
If not factory installed, follow steps 2-4 to route and secure the Ethernet cable to the cabinet.
Feed the Ethernet cable from your LAN network connecon through the cabinet base cable entry located in
the boom right, back of the cabinet (shown below).
Locate the (4) adhesive clips on the inside back wall. Feed the Ethernet cable through the clips and through
the opening to the control panel. Cable is routed away from the AC power cable to minimize electromagnec
interference (shown below). You may have to remove the dispenser assembly for ease of cable installaon.
5
Locate the strain relief grommet, insert cable, and close grommet. Insert grommet into the opening shown
below. If you need to adjust the cable length, gently push/pull on cable to desired length.
Obtain the iLAN box and the (4) Velcro pieces (2 so, 2 hard). Peel the paper backing o the two so pieces of
Velcro. Adhere them to the boom of the iLAN box. Once the so Velcro is secured in place, Velcro the hard
sides to the so pieces.
Connect the Ethernet cable to the back of the iLAN External Ethernet box. Locate the communicaon cable.
Connect the 9-Pin connector end to the back of the iLAN box (depending on connector end, you may need a
small at screwdriver to secure).
-
6
Connect the RJ-45 connector end of the communicaon cable to of the Docking Board assembly.
Locate just above Port 2. The jumper should be on to provide the necessary +12VDC to the
iLAN External Ethernet box.
Remove the paper backing from the hard pieces of Velcro. Place the iLan box onto the surface of the cabinet.
7
Secure the communicaon cable through the cable clip located nearby and e wrap the remainder of the
cable to the exisng cable harness.
8
If not factory installed, follow steps 2-4 to route and secure the Ethernet cable to the cabinet.
Unlock and open the control panel. Turn the power supply switch to the OFF (0) posion.
Feed the Ethernet cable from your LAN network connecon through the cabinet base cable entry located in the
lower le, back of the cabinet (shown below on the le).
Route the Ethernet cable up the le back wall of the cabinet and use the top cable clips to hold in place. Exit
cable up to control panel through access hole used for AC power cord. Cable is routed away from the AC power
cable to minimize electromagnec interference (shown below on the right). You may have to remove the dis-
penser assembly for ease of cable installaon.
9
Connect the Ethernet cable to the back of the iLAN box. Locate the communicaon cable. Connect the 9-Pin
connector end to the back of the iLAN box (depending on connector end, you may need a small at screwdriv-
er to secure).
Place the iLAN box on top of the card cage assembly. Secure the Ethernet cable using exisng cable clips
(shown below).
10
Pull the Memory module from the card cage
(SS-2) and verify the EPROM version is
or higher (right). If not, install the
required upgraded EPROM following ESD
precauons and correct orientaon of the
chip. Reinstall the Memory module aer
compleon.
The required module will
be installed in (SS-4) beneath the Mo-
dem/LCD module. Before installing, verify
that the jumpers on are connected
on If not, move the jumpers to
connect Pins 1 and 2 together (boom right).
Install the Memory Expansion module.
If your machine uses a (le), proceed to step 9.
Other manuals for 9600
2
This manual suits for next models
1
Other Triton Modem manuals
