TRENDnet TEW-511BRP User manual
Copyright ©2005. All Rights Reserved. TRENDware International, Inc.
TRENDnet
TRENDware, USA
What's Next in Networking
TEW-511BRP
Version 04.28.05
Dual-Band 802.11 a+g Wireless Router Quick Installation Guide
Guide d'installation rapide du
Routeur sans fil 802.11 a+g Dual band
Anleitung zur Schnellinstallation des
Drahtloser 802.11 a+g Dualband-Router
Guía de Instalación Rápida
Enrutador inalámbrico a+g 802.11 de Banda-Dual
Маршрутизатор для беспроводной связи Dual-Band 802.11 a+g
Руководство по быстрой установке
Table of Contents
English ................................................................................................................... 1
1
3
4
12
8
14
1. Prepare for Installation ...................................................................................
2. Install Hardware .............................................................................................
3. Configure the computer's TCP/IP Settings .....................................................
4. Configure your AP/Router ..............................................................................
5. Wireless Configuration ..................................................................................
6. Test your Connection .....................................................................................
Troubleshooting ...................................................................................................... 16
Thank you for purchasing the TEW-511BRP. This Wireless AP/Router will allow
you to securely share your Internet connection, files, and other resources with
multiple users.
This guide will help you set up and configure your AP/Router. Following the
installation instructions should be quick and easy. If you run into problems,
please refer to the Troubleshooting section or the more detailed installation
procedures on the User's Guide CD-ROM. If you need further technical
support, please visit www.TRENDNET.com or call technical support by phone.
Verify Equipment
Before installing the AP/Router, you should have:
1. An installed Cable/DSL Modem with an Ethernet Port
2. A Broadband Internet Account
3. A web browser such as Internet Explorer (5.0 or higher) or Netscape
Navigator (4.7 or higher)
4. A network cable for each computer
5. A computer with the TCP/IP Protocol and Client for Microsoft Networks
Service installed
Verify Package Contents
Please make sure you have everything in the box:
AC Power Adapter (5V, 2.5A)
User’s Guide CD-ROM
1
Quick Installation Guide
TEW-511BRP
1. Prepare for Installation
English QIG
English
RJ-45 Ethernet (LAN) Cable
Copyright ©2005. All Rights Reserved. TRENDware International, Inc.
TRENDnet
TRENDware, USA
What's Next in Networking
TEW-511BRP
Version 04.28.05
Dual-Band 802.11 a+g Wireless Router Quick Installation Guide
Guide d'installation rapide du
Routeur sans fil 802.11 a+g Dual band
Anleitung zur Schnellinstallation des
Drahtloser 802.11 a+g Dualband-Router
Guía de Instalación Rápida
Enrutador inalámbrico a+g 802.11 de Banda-Dual
Маршрутизатор для беспроводной связи Dual-Band 802.11 a+g
Руководство по быстрой установке
2
Collect Account Information from Internet
Service Provider (ISP)
During the installation of your AP/Router, the configuration utility will ask you to
specify your ISP connection type. Therefore, please verify your Cable or DSL
Internet broadband connection with your ISP and ensure you have all the
information for one of the following connection types:
Dynamic IP Cable Connection
Nothing is required. The IP address will be automatically be assigned by your
ISP.
Static or Fixed IP Cable Connection
Internet IP Address:____.____.____.____ (eg. 215.24.24.129)
Subnet Mask: ____. ____. ____. _____
Gateway IP Address:____.____.____._____
Primary DNS:____.____._____.______
Secondary DNS:_____._____._____.____
PPPoE Connection
Login Name:______________
Password:________________
PPTP DSL Connection
Internet IP Address:____.____.____.____ (eg. 215.24.24.129)
Subnet Mask: ____.____.____._____
Gateway IP Address:____.____.____._____
PPTP Server IP:____.____._____._____
Login Name:_______________
Password:_________________
English
3
2. Install Hardware
1. Connect one RJ-45 network cable from the Cable/DSL Modem's Ethernet
port to the WAN port on the AP/Router.
2. Connect a different RJ-45 network cable from one of the AP/Router's LAN
ports to your computer's network port.
3. Turn on your Cable/DSL modem.
4. Connect the included Power Adapter to your AP/Router and to your power
outlet; your AP/Router should turn on.
5. Turn on your computer
4
2
1
POWER
Verify Hardware Installation
Verify that the following front panel lights are on: Power, Internet, and one LAN
port LED for each wired computer connected to the AP/Router.
English
LAN
POWER
INTERNET
NOTE: Due to European Wireless Regulations, Super A Mode is not
supported in the EU version.
4
3. Configure the computer's TCP/IP Settings
Windows 2000/XP
1. Click Start; click Settings and click on Control Panel
2. Double-Click the Network Connections icon.
3. Right-Click on the Local Area Connection icon, and then click on
Properties. The Local Area Connection Properties box will appear.
4. Under the General Configuration Tab, locate and select TCP/IP, then
click Properties. The Internet Protocol (TCP/IP) Properties box will appear.
5. Click on Obtain an IP address automatically and Obtain DNS Server
address automatically.
NOTE: If you have a Fixed IP address connection, write down the
existing IP addresses from the following sections before you make any
changes.
English
5
6. Click OK.
7. Click Close on the Local Area Connection Properties box.
8. Click Start; click on Run. Then type cmd and click OK.
9. The Command Prompt window will appear. Type ipconfig at the
C:\ prompt and press the Enter key.
10. If your IP Configuration reads as follows, your computer is successfully
connected to the router:
IP Address: 192.168.1.x (x= any number from 2~255)
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.1
NOTE: If your IP Configuration does not match the values above, please
restart your computer and retry the steps in this section.
English
6
Windows 95/98/SE/ME
1. Click Start; click Settings and then click on Control Panel.
2. Double-Click the Network icon and the Network Properties box will appear.
3. Under the Configuration Tab, locate and select TCP/IP with the
corresponding network card (such as TRENDnet TE100-PCIWN
10/100Mbps Network Adapter), then click on the Properties button.
4. Under the IP Address Tab, click on the Obtain an IP address automatically
option.
5. Click OK on the TCP/IP Properties box.
6. Click OK on the Network Box.
7. At this point, the installation may require files from your Windows CD-ROM.
If this happens, insert your Windows CD-ROM into your CD-ROM drive
and select CD-ROM drive to load the files.
English
7
8. After the files load, the System Settings Change will appear, click
Yes to reboot your system. This will update your computer with the new
settings.
9. After your system reboots, click Start and click on Run. Then type
winipcfg in the field and then click OK.
10. The IP configuration box will appear. Choose your network adapter from the
dropdown box, and the utility will display your computer's current IP
address information.
11. If your IP Address reads as follows, your computer is successfully
connected to the router:
IP Address: 192.168.1.x (x= any number from 2~255)
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.1
NOTE: If the message does not appear, you need to manually restart
your computer.
NOTE: If your IP configuration does not match the values above, please
restart your computer and retry the steps in this section.
English
8
4. Configure your AP/Router
English
The following section will help you configure your AP/Router to connect to the
Internet and your PCs. The setup differs and is dependent on the type of
Internet connection you have. If you are not sure what type of connection you
have, please contact your ISP to obtain the required information, which is listed
in the Prepare for Installation section at the beginning of this Quick
Installation Guide.
1. Open your web browser, type http://192.168.1.1 in the Address bar, and
press Enter.
2. An authentication window will appear. Enter the username and password,
and then click OK. By default, the username is blank, and the password is
“admin.”
NOTE: To reset the password on the AP/Router, refer to the User's
Guide CD-ROM.
Other manuals for TEW-511BRP
4
Other TRENDnet Wireless Router manuals
TRENDnet
TRENDnet TEW-657BRM User manual
TRENDnet
TRENDnet TEW-817DTR User manual
TRENDnet
TRENDnet TEW-811DRU User manual
TRENDnet
TRENDnet TEW-718BRM User manual
TRENDnet
TRENDnet TEW-692GR User manual
TRENDnet
TRENDnet TPL-111BR - WIRELESS POWERLINE ROUTER 125 User manual
TRENDnet
TRENDnet TEW-671BR User manual
TRENDnet
TRENDnet TEW-511BRP User manual
TRENDnet
TRENDnet TEW-818DRU User manual
TRENDnet
TRENDnet TEW-818DRU User manual
TRENDnet
TRENDnet TPL-111BR - WIRELESS POWERLINE ROUTER 125 User manual
TRENDnet
TRENDnet GREENnet TEW-639GR User manual
TRENDnet
TRENDnet TEW-637AP - 300Mbps Wireless Easy-N-Upgrader User manual
TRENDnet
TRENDnet TEW-692GR User manual
TRENDnet
TRENDnet TEW-652BRU User manual
TRENDnet
TRENDnet TEW-651BR User manual
TRENDnet
TRENDnet TEW 632BRP - Wireless Router User manual
TRENDnet
TRENDnet TEW-691GR User manual
TRENDnet
TRENDnet TEW-690AP User manual
TRENDnet
TRENDnet TEW-751 DR User manual
