TRENDnet TEW-692GR User manual
Quick Installation Guide
TEW-692GR
1.01
Table of Contents
Version 05.05.2011
English 1
Troubleshooting 10
Wireless Tips
1. Before You Start 1
2. Hardware Installation 4
3. Configure the Wireless Router 6
13
ENGLISHFRANÇAISDEUTSCHESPAÑOL
РУССКИЙ
1. Before You Start
Package Contents
System Requirements
1
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
TEW-692GR
Multi-Language Quick Installation Guide
CD-ROM (User's Guide)
Network Cable (1.5m / 5ft)
Power Adapter (12V DC, 1A)
Ÿ
Ÿ
Ÿ
Ÿ
A computer with a wired or wireless network adapter properly installed
(Note: It is recommended that you configure the Wireless Router from a wired
computer)
Web Browser: Internet Explorer (6.0 or higher), Firefox 2.0 (6.0 or above), Opera,
Chrome, Safari
Broadband Internet
Installed Cable or DSL Modem
ENGLISHFRANÇAISDEUTSCHESPAÑOL
РУССКИЙ
2
Collect Internet Service Provider (ISP) Information
Please verify your Internet broadband connection type with your ISP and ensure you have all the information for
one of the following connection types:
1. DHCP (Dynamic IP Address)
Host Name (Optional): ________________
Manually Configure DNS (Enable/Disable)
Primary DNS Server: _____. _____._____._____
Secondary DNS Server: _____. _____._____._____
Use Default MTU Setting (Enable/Disable)
MTU (default: 1500)
MAC Address Clone (Enable/Disable)
2. Static IP Address
IP Address: _____. _____._____._____ (e.g. 215.24.24.129)
Subnet Mask: _____. _____._____._____
Default Gateway: _____. _____._____._____
Primary DNS Server: _____. _____._____._____
Secondary DNS Server: _____. _____._____._____
Use Default MTU Setting (Enable/Disable)
MTU (default: 1500)
MAC Address Clone (Enable/Disable)
3. PPP over Ethernet
User Name: ________________
Password: ________________
Manually Configure DNS (Enable/Disable)
Primary DNS Server: _____. _____._____._____
Secondary DNS Server: _____. _____._____._____
Operation Mode (Keep Alive, On Demand, Manual)
Keep Alive Mode Redial Period (Default: 10 seconds)
On Demand Mode Idle Time (Default: 5 minutes)
Use Default MTU Setting (Enable/Disable)
MTU (default: 1500)
MAC Address Clone (Enable/Disable)
4. PPTP
PPTP Server IP Address: ________________
User Name: ________________
Password: ________________
Address Mode: Dynamic IP or Static IP
IP Address:_____. _____._____._____ (e.g. 215.24.24.129)
Subnet Mask: _____. _____._____._____
Default Gateway: _____. _____._____._____
Operation Mode (Keep Alive, On Demand, Manual)
Keep Alive Mode Redial Period (Default: 10 seconds)
On Demand Mode Idle Time (Default: 5 minutes)
Primary DNS Server: _____. _____._____._____
Secondary DNS Server: _____. _____._____._____
Use Default MTU Setting (Enable/Disable)
MTU (default: 1500)
MAC Address Clone (Enable/Disable)
ENGLISHFRANÇAISDEUTSCHESPAÑOL
РУССКИЙ
3
5. L2TP
Server IP Address : ________________
User Name: ________________
Password: ________________
WAN Interface IP Type: Dynamic IP or Static IP
IP Address:_____. _____._____._____ (e.g. 215.24.24.129)
Subnet Mask: _____. _____._____._____
Default Gateway: _____. _____._____._____
Operation Mode (Keep Alive, On Demand, Manual)
Keep Alive Mode Redial Period (Default: 10 seconds)
On Demand Mode Idle Time (Default: 5 minutes)
Primary DNS Server: _____. _____._____._____
Secondary DNS Server: _____. _____._____._____
Use Default MTU Setting (Enable/Disable)
MTU (default: 1500)
MAC Address Clone (Enable/Disable)
ENGLISHFRANÇAISDEUTSCHESPAÑOL
РУССКИЙ
2. Hardware Installation
4
Note: Gather all information related to your Internet Connection before you start. If necessary,
contact your Internet Service Provider (ISP).
Cable/DSL Modem
Internet
1. Verify that you have an Internet connection
when connecting your computer directly to the
Cable or DSL modem. Open your browser (e.g.
Internet Explorer) and type in a URL (e.g.
http://www.trendnet.com) in the address bar.
2. Power off your cable or DSL modem.
3. Disconnect the network cable from your Cable
or DSL modem and your computer.
4. Connect one end of a network cable to one of
the TEW-692GR's network ports. Connect the
other end of the cable to the computer's
network port.
5. Connect one end of a network cable to the
TEW-692GR's WAN port. Connect the other
end of the cable to your modem's network port.
ENGLISHFRANÇAISDEUTSCHESPAÑOL
РУССКИЙ
5
7. Power on your cable or DSL modem. Wait until
the LEDs indicate that modem is fully booted
up. Consult with the modem user's guide for
more information.
6. Connect the Power Adapter to the TEW-692GR
and then to a power outlet. Move the power
switch to the “On” position (EU version only).
8. Verify that the following panel lights are on:
Power (Green), LAN (port (1,2,3,4) your
computer is connected to)(Green), WAN
(Green), Wireless (2.4GHz)(Green) and
Wireless (5GHz)(Blue). Please see trouble
shooting section for additional information on
LED behaviors.
ENGLISHFRANÇAISDEUTSCHESPAÑOL
РУССКИЙ
6
3. Configure the Wireless Router
Note: It is recommended that you configure the Wireless Router from a wired computer.
3. Click Wizard.
1. Open your web browser, type
http://192.168.10.1 in the Address bar, and
then press Enter.
2. Enter the User Name and Password and then
click OK. By default:
User Name: admin
Password: admin
Note: User name is case sensitive.
4. Click Launch Internet Connection Setup
Wizard.
5. Click Next.
ENGLISHFRANÇAISDEUTSCHESPAÑOL
РУССКИЙ
7
10. Click Wizard.
6. Select the proper Internet Connection Type.
Configure the settings based on information
provided by your ISP. Then click Next.
Note: Each Internet Connection type may have
different options.
7. Click Apply.
8. Click OK.
9. Please wait while the router reboots.
11. Click Wireless Security Setup Wizard.
ENGLISHFRANÇAISDEUTSCHESPAÑOL
РУССКИЙ
8
12. You will need to configure the following:
Wireless Network Name (SSID) (2.4GHz)
Wireless Network Name (SSID) (5GHz)
The SSID is the wireless network name of
your wireless network (e.g. wireless router or
access point). Enter a unique SSID. Choose
something that you would easily identify when
searching for available wireless networks.
Then click Apply.
Note:
1. To protect your network from any unauthorized access it is recommended to enable wireless
encryption.
2. The example below is for WPA-PSK/WPA2-PSK (AES) (Best) security. If you select WPA-PSK
or WPA2-PSK, make sure your wireless adapters support WPA or WPA2. If your wireless
adapters do not support WPA or WPA2, then select WEP (Good).
3. WEP encryption only supports 802.11b/g speed of up to 54Mbps.
4. Once encryption is enabled on the router, each wireless computer and device must be
configured with the same encryption key.
13. Select Best and then click Apply.
14. Enter characters for your wireless security
password and then click Apply. For
WPA-PSK or WPA2-PSK, the Pre-Shared Key
must be between 8 and 63 ASCII or 64 HEX
characters. Make sure to copy down the
Pre-Shared Key. You will need the Pre-Shared
key when you configure your wireless
adapter(s).
Other manuals for TEW-692GR
3
Table of contents
Other TRENDnet Wireless Router manuals
TRENDnet
TRENDnet TEW-651BR User manual
TRENDnet
TRENDnet TEW-435BRM - 54MBPS 802.11G Adsl Firewall M User manual
TRENDnet
TRENDnet AC1750 User manual
TRENDnet
TRENDnet TEW-211BRP User manual
TRENDnet
TRENDnet TEW-751DR User manual
TRENDnet
TRENDnet TEW-659BRV Operating instructions
TRENDnet
TRENDnet TEW-812DRU User manual
TRENDnet
TRENDnet TEW 632BRP - Wireless Router User manual
TRENDnet
TRENDnet TEW-718BRM User manual
TRENDnet
TRENDnet TEW-659BRV Operating instructions
TRENDnet
TRENDnet TEW-672GR User manual
TRENDnet
TRENDnet TEW-652BRU User manual
TRENDnet
TRENDnet TEW-657BRM User manual
TRENDnet
TRENDnet N450 TEW-691GR User manual
TRENDnet
TRENDnet TEW-311BRP User manual
TRENDnet
TRENDnet TEW-751 DR User manual
TRENDnet
TRENDnet TEW-692GR User manual
TRENDnet
TRENDnet TEW-411BRPplus User manual
TRENDnet
TRENDnet EasyMesh TEW-832MDR User manual
TRENDnet
TRENDnet TEW-411BRP User manual
