TRENDnet TEW-740APBO User manual
TEW-740APBO
Quick Installation Guide
Table of Content
1 English
1. Before You Start
2. Hardware Configuration
3. Hardware Installation
1
1. Before You Start
Package Contents
ŸTEW-740APBO
ŸCD-ROM (User's Guide)
ŸQuick Installation Guide
ŸProprietary PoE injector
ŸPower adapter (12 V DC, 1 A)
ŸMounting Hardware
ŸGrounding wire
Minimum Requirements
ŸComputer with a network port and web browser
ŸA network switch or router with an available network LAN port
ŸAdditional TEW-740APBO H/W: v2.xR wireless N300 directional access point
Ÿ4 x RJ-45 network cables
Note:
It is recommended to use network cables without additional caps, molded caps, or boots with
the access points for cable fitment inside the enclosure.
Note:
The TEW-740APBO does not support IEEE 802.3at/af PoE standards. You must use the
proprietary Power over Ethernet injector that is supplied with the TEW-740APBO. This
installation guide will walk you through the installation and configuration of two TEW-740APBO
access points to establish a wireless point to point bridge using WDS (wireless distribution
system). The RJ-45 Ethernet cable between the passive PoE injector and access point can have
a maximum length of up to 60 m (197 ft.).
ENGLISHFRANÇAISDEUTSCH
ESPAÑOLРORTUGUÊS
2
2. Hardware Setup and Configuration
Note:
Ÿ The default IP address of the TEW-740APBO is 192.168.10.100. To configure the
TEW-740APBO, your network adapter must have an IP address within the 192.168.10.x
subnet (e.g. 192.168.10.10). Please refer to the Appendix in the User's Guide for more
information.
Ÿ The initial configuration should be completed in a testing environment with two
TEW-740APBO access points approximately 15 ft. (5 m) apart from one another with the
front of the access points directly facing each other.
ŸConfigure and connect the access points before mounting.
Phase 1: Overview
In this installation guide, we will assume the following:
Router Settings:
Router/Default Gateway IP address: 192.168.10.1
Subnet Mask: 255.255.255.0
The TEW-740APBO access points will be configured with the following settings:
TEW-740APBO #1
IP Address: 192.168.10.50
Netmask (Subnet Mask): 255.255.255.0
IP Gateway (Default Gateway): 192.168.10.1
Primary DNS: 192.168.10.1
Wireless Channel (Default): 1
WDS AES Encryption
TEW-740APBO #2
IP Address: 192.168.10.51
Netmask (Subnet Mask): 255.255.255.0
IP Gateway (Default Gateway): 192.168.10.1
Primary DNS: 192.168.10.1
Wireless Channel (Default): 1
WDS AES Encryption
In this example, we will assume the device use the following MAC addresses:
TEW-740APBO #1 MAC Address: 00:11:22:33:44:00
TEW-740APBO #2 MAC Address: 00:11:22:33:44:11
Phase 2: TEW-740APBO Unit #1 Hardware Setup and Configuration
1. Remove the cover of the access point by pulling and holding the tab in the vertical direction
upward (based on the access point orientation below) and sliding the cover in the two
locations noted below away from the access point.
Pull and hold tab
2. Write down the MAC address (WiFi MAC) of the TEW-740APBO #1 access point. The MAC
address (WiFi MAC) can be found on the inside of the device cover where the Ethernet LAN
ports are located (shown below).
3
WIFI MAC: XXXXXXXXXXXXXXXXX
ETH LAN1 MAC: XXXXXXXXXXXXXXXXX
Model No: TEW-740APBO / A S/N: XXXXXXXXXXXXXXX
H/W: V2.0RFW: V2.XXXXX
Made in XXXXXX
ENGLISHFRANÇAISDEUTSCH
ESPAÑOLРORTUGUÊS
4
3. Remove the tab on the far left by gently bending it back and forth until the tab is removed.
This will create the opening for a RJ-45 network cable to be routed through.
Tab
4. Using a network cable, connect one end of the cable to the LAN (PoE) port and push the cable
into the cable guide on the far left, then through the opening that was created in the previous
step.
Cable Guide
5
5. Connect the other end of the network cable to the P+DATA OUT port on the included PoE
injector.
6. Using another network cable, connect one end to the 10/100 DATA IN port on the included
PoE injector.
7. Connect the other end of the network cable to your computer's Ethernet port.
8. Connect the included power adapter to the PoE injector POWER IN on the included PoE
injector.
9. Plug the connected power adapter into a power outlet.
10. Confirm the device is powered on through the LED indicators.
Included PoE injector
LAN1 (PoE)
P+DATA OUT
POWER IN 10/100Mbps DATA IN
11. Assign a static IP address to your computer's network adapter in the subnet of
192.168.10.x (e.g. 192.168.10.10) and subnet mask of 255.255.255.0.
ENGLISHFRANÇAISDEUTSCH
ESPAÑOLРORTUGUÊS
6
12. Open your web browser and type the IP address of the access point in the address bar, then
press Enter. The default IP address is 192.168.10.100.
13. When prompted, login to the browser configuration page using the default user name and
password settings.
User Name: admin
Password: admin
Note: User Name and Password are case sensitive.
14. Click on the System tab and select Management.
Management
System
7
15. Under Administrator Password, change the default administrator password by typing in
your new password in the fields provided and then click the Save button at the bottom of
the page.
Save
Reboot
16. After the device saves changes and reboots, in the top menu, click on the System and click
on Mode Setup.
Mode Setup
System
ENGLISHFRANÇAISDEUTSCH
ESPAÑOLРORTUGUÊS
8
17. Click on the Mode field and click on WDS Mode. Then click Save & Reboot and when
prompted to change settings, click Yes to reboot the device and apply the changes.
WDS Mode
Save & Reboot
18. In the top menu, click on System and click on VLAN Setup.
VLAN Setup
System
19. For the first entry in the VLAN List under the action column, click Network.
Network
Other manuals for TEW-740APBO
4
Table of contents
Other TRENDnet Wireless Access Point manuals
TRENDnet
TRENDnet TPL-110AP - 125Mbps 802.11g Wireless Powerline Access... User manual
TRENDnet
TRENDnet TEW-826DAP User manual
TRENDnet
TRENDnet TEW-753DAP User manual
TRENDnet
TRENDnet 14dBi User manual
TRENDnet
TRENDnet TEW -739APBO User manual
TRENDnet
TRENDnet TEW-735AP User manual
TRENDnet
TRENDnet TEW-AP100plus User manual
TRENDnet
TRENDnet TEW-734APO User manual
TRENDnet
TRENDnet TEW-430APB - Wireless Access Point User manual
TRENDnet
TRENDnet TEW-230APB User manual
TRENDnet
TRENDnet TPL-110AP - 125Mbps 802.11g Wireless Powerline Access... User manual
TRENDnet
TRENDnet TEW-450APB - Wireless Super G Access Point Installation guide
TRENDnet
TRENDnet TEW-820AP User manual
TRENDnet
TRENDnet TEW-435BRM - 54MBPS 802.11G Adsl Firewall M User manual
TRENDnet
TRENDnet TEW-412APBO User manual
TRENDnet
TRENDnet TEW-670APB User manual
TRENDnet
TRENDnet TEW-638PAP User manual
TRENDnet
TRENDnet TEW-690AP User manual
TRENDnet
TRENDnet TEW-410APB User manual
TRENDnet
TRENDnet TEW-453APB - 108Mbps Wireless Super G HotSpot Access... User manual
