TRENDnet TE100-S16R User manual
TE100-S16R
16-Port 10/100Mbps
NWay Ethernet Switch
User’s Guide
FCC Warning
This equipment has been tested and found to comply with the
regulations for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with this user’s guide, may cause harmful interference to
radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference, in which case the user will
be required to correct the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product
may cause radio interference, in which case the user may be required
to take adequate measures.
P/N: 6012-3216211 Rev.A1-01
UL Warning
a) Elevated Operating Ambient Temperature-If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may be greater
than room ambient. Therefore, consideration should be given to installing the
equipment in an environment compatible with the manufacturer's maximum rated
ambient temperature (Tmra).
b) Reduced Air Flow-Installation of the equipment in a rack should be such that the
amount of air flow required for safe operation of the equipment is not compromised.
c) Mechanical Loading-Mounting of the equipment in the rack should be such that a
hazardous condition is not achieved due to uneven mechanical loading.
d) Circuit Overloading-Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of circuits might have on
overcurrent protection and supply wiring. Appropriate consideration of equipment
nameplate ratings should be used when addressing this concern.
e) Reliable Earthing-Reliable earthing of rack-mounted equipment should be
maintained. Particular attention should be given to supply connections other than direct
connections to the branch circuit (e.g., use of power strips).
i
TABLE OF CONTENTS
ABOUT THIS GUIDE............................................................III
PURPOSE..................................................................................................III
TERMS/USAGE ......................................................................................III
OVERVIEW OF THIS USER’S GUIDE.............................................III
INTRODUCTION.........................................................................1
FAST ETHERNET TECHNOLOGY......................................................1
SWITCHING TECHNOLOGY ................................................................2
FEATURES .................................................................................................3
UNPACKING AND INSTALLATION....................5
UNPACKING..............................................................................................5
INSTALLATION........................................................................................5
RACK MOUNTING..................................................................................6
IDENTIFYING EXTERNAL COMPONENTS
...........................................................................................................................7
FRONT PANEL..........................................................................................7
REAR PANEL............................................................................................8
LED INDICATORS..................................................................................9
TRUNKING SETTING..............................................................................9
QOS (QUALITY OF SERVICE) SETTING......................................12
ii
CONNECTING THE SWITCH...................................15
PC TO SWITCH......................................................................................15
HUB TO SWITCH...................................................................................15
A. 10BASE-T Hub.............................................................................16
B. 100BASE-TX Hub........................................................................16
HUB WITHOUT UPLINK (MDI-II) PORT .....................................16
A. Using straight cable....................................................................16
B. Using crossover cable................................................................16
SWITCH TO SWITCH (OTHER DEVICES)......................................17
A. Using straight cable....................................................................17
B. Using crossover cable................................................................17
PORT S PEED & DUPLEX MODE....................................................17
TECHNICAL SPECIFICATIONS............................19
iii
ABOUT THIS GUIDE
Congratulations on your purchase of the 16-Port 10/100Mbps NWay
Ethernet Switch. This device integrates 100Mbps Fast Ethernet and
10Mbps Ethernet network capabilities in a highlyflexible package.
Purpose
This guide discusses how to install your 16-Port 10/100Mbps NWay
Ethernet Switch.
Terms/Usage
In this guide, the term “Switch” (first letter upper case) refers to your
16-Port 10/100Mbps NWay Ethernet Switch, and ”switch” (first letter
lower case) refers to other Ethernet switches.
Overview of this User’s Guide
Introduction. Describes the Switch and its features.
Unpacking and Installation. Helps you get started with the basic
installation of the Switch.
Identifying External Components. Describes the front panel, rear
panel and LED indicators of the Switch.
Connecting the Switch. Tells how you can connect the Switch to your
Ethernet network.
Technical Specifications. Lists the technical (general, physical and
environmental, and performance) specifications of the Switch.
RJ-45 Pin Specification. Describes the RJ-45 receptacle/connector
and the straight through and crossover cable connector.
1
INTRODUCTION
This chapter describes the features of the Switch and some
background information about Ethernet/Fast Ethernet switching
technology.
Fast Ethernet Technology
The growing importance of LANs and the increasing complexity of
desktop computing applications are fueling the need for high
performance networks. A number of high-speed LAN technologies
have been proposed to provide greater bandwidth and improve
client/server response times. Among them, 100BASE-TX (Fast
Ethernet) provides a non-disruptive, smooth evolution from the
current 10BASE-T technology. The non-disruptive and smooth
evolution nature, and the dominating potential market base, virtually
guarantee cost effective and high performance Fast Ethernet solutions
in the years to come.
100Mbps Fast Ethernet is a new standard specified by the IEEE 802.3
LAN committee. It is an extension of the 10Mbps Ethernet standard
with the ability to transmit and receive data at 100Mbps, while
maintaining the CSMA/CD Ethernet protocol. Since the Switch is
compatible with all 10Mbps Ethernet environments, it provides a
straightforward upgrade and takes advantage of the existing
investment in hardware, software, and personnel training.
2
Switching Technology
Another approach to pushing beyond the limits of Ethernet technology
is the development of switching technology. A switch bridges and
transmits Ethernet packets at the MAC address level of the Ethernet
protocol, among connected Ethernet or Fast Ethernet LAN segments.
Switching is a cost-effective way of increasing the total network
capacity available to users on a local area network. A switch
increases capacity and decreases network loading by dividing a local
area network into different segments. Each segment has its own
bandwidth and it does not compete with others for network
transmission capacity.
A switch acts as a high-speed selective bridge between the individual
segments. The switch forwards traffic from origin segment to
destination segment, without interfering with any other segments. By
doing this, the total network capacity is multiplied, while still
maintaining the same network cabling and adapter cards.
For Fast Ethernet networks, a switch is an effective way of eliminating
problems of uplinking Fast Ethernet hubs beyond the “two-repeater
limit”. A switch can be used to split parts of the network into different
collision domains, making it possible to expand your Fast Ethernet
network beyond the 205-meter network diameter limit. The switch
supports both traditional 10Mbps Ethernet and 100Mbps Fast
Ethernet, which is also ideal for bridging between the existing
10Mbps networks and the new 100Mbps networks.
LAN Switching technology is a marked improvement over the
previous generation of network bridges, which were criticized by their
higher latencies. Routers have also been used to segment local area
networks. But, the router expensive, difficult to setup, and
Other manuals for TE100-S16R
3
Table of contents
Other TRENDnet Network Router manuals
TRENDnet
TRENDnet TW100-BRV204 SHEETS User manual
TRENDnet
TRENDnet TEW-452BRP - 108Mbps Wireless Super G Broadband... User manual
TRENDnet
TRENDnet TEG-S160TX - Gigabit Switch With 31 Gbps Switching... User manual
TRENDnet
TRENDnet TEW-652BRP User manual
TRENDnet
TRENDnet TW100 TW100-BRV304 Installation and operation manual
TRENDnet
TRENDnet TEW-635BRM - Wireless Router User manual
TRENDnet
TRENDnet TW100-BRF114 User manual
TRENDnet
TRENDnet TW100-BRV204 SHEETS User manual
TRENDnet
TRENDnet TEW-811DRU User manual
TRENDnet
TRENDnet TEW-436BRM User manual
TRENDnet
TRENDnet SMCWBR14S-NL User manual
TRENDnet
TRENDnet TEW711BRV2 User manual
TRENDnet
TRENDnet TEW-840APBO User manual
TRENDnet
TRENDnet TW100-BRF114 Instruction Manual
TRENDnet
TRENDnet TEW-431BRP Installation guide
TRENDnet
TRENDnet TEW827DRUV2 User manual
TRENDnet
TRENDnet TEG-S83A User manual
TRENDnet
TRENDnet TE100-S2424V User manual
TRENDnet
TRENDnet TW100-S4W1CA User manual
TRENDnet
TRENDnet TW100-BRV204 SHEETS User manual
