TRENDnet TW100-BRF114U Installation guide
F.A.Q for TW100-BRF114U
Q: How do I configure the TW100-BRF114U for a DSL, PPPoE connection?
A: Open your web browser and type the IP address of the TW100-BRF114U in the address bar.
The default IP address is 192.168.0.1. At the login, enter your username (blank) and password
(blank). NOTE: If the Setup Wizard starts, click on Cancel.
Click on Advanced then WAN Port on the left hand side.
1) Choose PPPoE for the Login Method in the Login section.
2) Enter your Username and Password provided by your ISP (Internet Service Provider).
3) Click on the down arrow for the Connection behavior and select “keepalive”.
4) Click Save.
Note: After you save the settings you may need to power cycle the modem and router.
1) Disconnect the power cycle from the modem and router.
2) Wait approximately 15 seconds.
3) Reconnect the modem first and wait for it to boot up.
4) After the modem has booted up reconnect the router.
04/03/2006
5) Open your web browser and type the IP address of the TW100-BRF114U in the address
bar. The default IP address is 192.168.0.1. At the login, enter your username (blank) and
password (blank). NOTE: If the Setup Wizard starts, click on Cancel.
6) Go to Status on the left hand side of the screen and then click on Connection Details.
This will open a new window.
04/03/2006
7) Click on Connect, wait a few seconds and see if it gets an IP address from your ISP.
Q: How do I configure the TW100-BRF114U for a Cable connection using a Dynamic IP
Address?
A: Note: The default setting of the router is configured for a Cable connection using a Dynamic
IP Address.
1) Open your web browser and type the IP address of the TW100-BRF114U in the address
bar. The default IP address is 192.168.0.1. At the login, enter your username (blank) and
password (blank). NOTE: If the Setup Wizard starts, click on Cancel.
2) Click on Advanced then WAN Port on the left hand side
3) If your ISP has registered the MAC address of your computer that you are managing the
router from click on Copy From PC under the WAN PORT MAC Address field. This
will copy your computers MAC address to the router. If you are not managing the
computer from the computer with the registered MAC address make sure you enter the
registered MAC address manually.
4) Choose None (Direct Connection) in the Login Method field in the Login section.
5) Click Save.
04/03/2006
Note: After you save the settings you may need to power cycle the modem and router.
1) Disconnect the power cycle from the modem and router.
2) Wait approximately 15 seconds.
3) Reconnect the modem first and wait for it to boot up.
4) After the modem has booted up reconnect the router. Open your web browser and type
the IP address of the TW100-BRF114U in the address bar. The default IP address is
192.168.0.1. At the login, enter your username (blank) and password (blank). NOTE: If
the Setup Wizard starts, click on Cancel.
5) Go to Status on the left hand side of the screen and then click on Connection Details. This
will open a new window.
04/03/2006
04/03/2006
7) Click on Renew, wait a few seconds and see if it gets an IP address from your ISP.
Q: How do I change the username & password on my TW100-BRF114U?
A: Open your web browser and type the IP address of the TW100-BRF114U in the address bar.
The default IP address is 192.168.0.1. At the login, enter your username (blank) and password
(blank). NOTE: If the Setup Wizard starts, click on Cancel.
1) Click on Password on the left hand side.
04/03/2006
2) Enter in the desired username and password.
3) Click Save.
Q: What can I do if I forgot my password or want to reset back to factory defaults?
1) Locate the reset button on the back of the TW100-BRF114U.
2) Press and hold in the reset button for approximately 15 seconds. This will reset
the unit back to its default configuration.
Q: What is the default IP address of my TW100-BRF114U?
A: The default IP address for the TW100-BRF114U is 192.168.0.1.
Q: What is the default username and password for the TW100-BRF114U?
A: The default username & password for the TW100-BRF114U are both (blank). There is no
username and password set by default.
04/03/2006
Q: How do I change the IP Address of my TW100-BRF114U?
1) Open your web browser and type the IP address of the TW100-BRF114U in the address
bar. The default IP address is 192.168.0.1. At the login, enter your username (blank) and
password (blank). NOTE: If the Setup Wizard starts, click on Cancel.
2) Click on LAN on the left hand side.
3) Change the IP address in the IP Address field.
4) Click Save.
Q: How do I configure the TW100-BRF114U?
A: Click Start then click on the Control Panel. For Windows 2000 click on Start, highlight
settings then click on the Control Panel.
1) Double-Click on the Network Connection icon.
2) Right-Click on the Local Area Connection icon then click on Properties.
3) Highlight the Internet Protocol (TCP/IP) by single clicking on it then click on
Properties.
04/03/2006
4) Select Obtain an IP address automatically and Obtain DNS server address
automatically then click OK.
04/03/2006
5) Click OK again.
04/03/2006
Other manuals for TW100-BRF114U
3
Table of contents
Other TRENDnet Network Router manuals
TRENDnet
TRENDnet TEW-818DRU User manual
TRENDnet
TRENDnet TWG-431BR User manual
TRENDnet
TRENDnet TEW-823DRU User manual
TRENDnet
TRENDnet TK-EX4 User manual
TRENDnet
TRENDnet TDM-C500 User manual
TRENDnet
TRENDnet TEG-S83A User manual
TRENDnet
TRENDnet TEW-658BRM User manual
TRENDnet
TRENDnet TEW-435BRM - 54MBPS 802.11G Adsl Firewall M User manual
TRENDnet
TRENDnet TEW-WLC100P User manual
TRENDnet
TRENDnet TE100-S50g User manual
TRENDnet
TRENDnet TEW-633GR - Wireless Router Installation and operation manual
TRENDnet
TRENDnet TEW-721BRM User manual
TRENDnet
TRENDnet TEG-S16g User manual
TRENDnet
TRENDnet TEW-721BRM User manual
TRENDnet
TRENDnet TEW-652BRP User manual
TRENDnet
TRENDnet TVP-224HR User manual
TRENDnet
TRENDnet TW100-BRF104 User manual
TRENDnet
TRENDnet TE100-S88E User manual
TRENDnet
TRENDnet TEW-752DRU User manual
TRENDnet
TRENDnet TE100-S2424V User manual
