TRENDnet TEG-PCITXM User manual

32-bit PCI

10/100/1000Mbps

Gigabit Ethernet Card

User’s Guide

FCC Warning

This equipment has been tested and found to comply with

the regulations for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with this

user’s guide, may cause harmful interference to radio

communications. Operation of this equipment in a

residential area is likely to cause harmful interference, in

which case the user will be required to correct the

interference at his own expense.

CE Mark Warning

This is a Class B product. In a domestic environment, this

product may cause radio interference, in which case the

user may be required to take adequate measures.

VCCI Warning

P/N: 1907GA1100T5000 Rev.A1-01

TABLE OF CONTENTS

INTRODUCTION.............................................................. 1

FEATURES ......................................................................... 1

GIGABIT ETHERNET TECHNOLOGY .................................. 2

FAST ETHERNET TECHNOLOGY........................................ 3

UNPACKING AND INSTALLATION ........................... 4

UNPACKING ...................................................................... 4

INSTALLING THE GIGABIT ETHERNET CARD ................... 5

CONNECTING THE NETWORK CABLE ............................... 6

SOFTWARE INSTALLATION............................................... 6

LED INDICATORS........................................................... 7

TECHNICAL SPECIFICATIONS .................................. 8

INTRODUCTION

Thank you for choosing the 10/100/1000Mbps Gigabit

Ethernet Card for 32-bit PCI Bus-equipped personal

computers. The 32-bit PCI 10/100/1000Mbps Gigabit

Ethernet Card is ideal for speeding up data transfers for

network servers and other computers, such as those used for

video-conferencing, that send and/or receive large amounts

of data. The 32-bit PCI 10/100/1000Mbps Gigabit Ethernet

Card also includes the newest networking technologies,

such as multicasting support, that use network bandwidth

more efficiently and further help the card maximize data

throughput.

Features

IEEE 802.3, 802.3u and 802.3z compliant

Support 32-bit 33/66Mhz PCI Local Bus Master

high-speed operation of Rev.2.1/2.2 specification

Plug-and-Play installation

One RJ-45 connector: Auto detection of 10Mbps

Ethernet, 100Mbps Fast Ethernet and 1000Mbps

Gigabit Ethernet & Auto MDI-X

Supports 10/100/1000Mbps Auto-negotiation

operation

Full Duplex support for 10/100/1000Mb/s data rates

Auto MDI-II/MDI-X crossover for all three speeds

128Kb RAM on-chip buffer

802.3x Full duplex flow control, including

automatic transmission of Pause frames based on Rx

FIFO thresholds

Five LED indicators for easy diagnostic

Gigabit Ethernet Technology

Gigabit Ethernet is an extension of IEEE 802.3 Ethernet

utilizing the same packet structure, format, and support for

CSMA/CD protocol, full duplex, and management objects,

but with a tenfold increase in theoretical throughput over

100Mbps Fast Ethernet and a one hundred-fold increase

over 10Mbps Ethernet. Since it is compatible with all

10Mbps and 100Mbps Ethernet environments, Gigabit

Ethernet provides a straightforward upgrade without

wasting a company’s existing investment in hardware,

software, and trained personnel.

The increased speed and extra bandwidth offered by

Gigabit Ethernet is essential to coping with the network

bottlenecks that frequently develop as computers and their

busses get faster and more users use applications that

generate more traffic. Upgrading key components, such as

your backbone and servers to Gigabit Ethernet can greatly

improve network response times as well as significantly

speed up the traffic between your subnets.

Gigabit Ethernet enables Twisted-Pair cable connections to

support video conferencing, complex imaging, and similar

data-intensive applications. Likewise, since data transfers

occur 10 times faster than Fast Ethernet, servers outfitted

with Gigabit Ethernet NIC’s are able to perform 10 times

the number of operations in the same amount of time.

Fast Ethernet Technology

The growing importance of LANs and the increasing

complexity of desktop computing applications are fueling

the need for high performance networks. A number of

high-speed LAN technologies have been proposed to

provide greater bandwidth and improve client/server

response times. Among them, 100BASE-T (Fast Ethernet)

provides a non-disruptive, smooth evolution from the

current 10BASE-T technology. The non-disruptive and

smooth evolution nature, and the dominating potential

market base, virtually guarantee cost effective and high

performance Fast Ethernet solutions in the years to come.

100Mbps Fast Ethernet is a new standard specified by the

IEEE 802.3 LAN committee. It is an extension of the

10Mbps Ethernet standard with the ability to transmit and

receive data at 100Mbps, while maintaining the CSMA/CD

Ethernet protocol. Since the 100Mbps Fast Ethernet is

compatible with all other 10Mbps Ethernet environments, it

provides a straightforward upgrade and takes advantage of

the existing investment in hardware, software, and

personnel training.

UNPACKING AND INSTALLATION

This chapter provides unpacking and installation

information for the 32-bit PCI 10/100/1000Mbps Gigabit

Ethernet Card.

Unpacking

CAUTION: Under ordinary circumstances, the 32-bit PCI

10/100/1000Mbps Gigabit Ethernet Card will not be

affected by static charge as may be received through

your body during handling of the unit. However, there

are special circumstances where you may carry an

extraordinarily high static charge, and possibly

damage the card and/or your computer. It is good

practice to eliminate all static electricity by touching

a ground (an unpainted metal area of your computer

chassis, for example) before performing any

installations.

Open the shipping carton and carefully remove all items. In

addition to this User's Guide, ascertain that you have:

One 32-bit PCI 10/100/1000Mbps Gigabit Ethernet

Card.

One Driver Diskette

This User’s Guide.

If any item is found missing or damaged, please contact

your local reseller for replacement.

Installing the Gigabit Ethernet Card

1. Shut down the computer, unplugs its power cord, and

remove the chassis cover.

2. Insert the contact edge of the Gigabit Ethernet card into

the connector of any available PCI Bus Master

expansion slot. Press the card firmly into the connector

such that the card’s contacts are fully seated in the

connector, this card can put either in 32-bit or 64-bit

PCI slot, but it is recommended that the card to put in

the PCI slot supported 66Mhz to have the maximum

performance.

3. Install the bracket screw and secure the card to the

computer chassis.

4. Cover the computer’s chassis.

5. Switch computer power on. If the BIOS section of your

computer’s boot program is Plug-and-Play compliant,

then at power-up the BIOS will automatically configure

any newly installed the Gigabit Ethernet Card.

NOTE: Due to a fault in some Plug-n-Play BIOS programs, it

happens occasionally that a newly installed adapter is

assigned an Interrupt Number which is already assigned to

another device. In such a case, the conflict of Interrupt

Number will cause faults in the behavior of both devices.

Then it is necessary to run the CMOS Setup utility, and

manually assign a non-conflicting Interrupt Number.

Connecting the Network Cable

Four pair of Cat.5 UTP or STP cable with RJ-45 connector

is required for the 32-bit PCI 10/100/1000Mbps Gigabit

Ethernet Card. You can use standard or crossover cable to

connect the switch MDI-X or MDI-II port, because the 32-

bit PCI 10/100/1000Mbps Gigabit Ethernet Card will adjust

the correct signal automatically.

Software Installation

Before you connect the 32-bit PCI 10/100/1000Mbps

Gigabit Ethernet Card to the network, you have to install

the network driver first. The driver for each networking

operating system is under a separate directory. A

HELPME.COM file under root directory lists the

information and detailed installation procedure of all the

available drivers.

LED INDICATORS

z10Mbps Fast Ethernet Link (10)

This indicator lights green when the Gigabit Card is

connects to 10Mbps Ethernet Network.

z100Mbps Fast Ethernet Link (100)

This indicator lights green when the Gigabit Card is

connects to 100Mbps Fast Ethernet Network.

z1000Mbps Gigabit Ethernet Link (1000)

This indicator lights green when the Gigabit Card is

connects to 1000Mbps Gigabit Ethernet Network.

zActivity (ACT)

This indicator blinking green will be transmitting or

received data on the network.

zFull-duplex mode (FDX)/ Collision (COL)

This LED indicator lights green when the Gigabit Card

is work on full duplex (FDX) mode. Otherwise, it is

blinking when collisions are occurring on the Gigabit

Card.

TECHNICAL SPECIFICATIONS

General

Standards IEEE 802.3 10Base-T Ethernet

IEEE 802.3u 100Base-TX Fast Ethernet

IEEE 802.3ab 1000Base-T Gigabit Ethernet

IEEE 802.3x Flow Control

Protocol CSMA/CD

Data Transfer Rate Ethernet: 10Mbps (half), 20Mbps (full)

Fast Ethernet: 100Mbps (half), 200Mbps (full)

Gigabit Ethernet: 1000Mbps (half), 2000Mbps (full)

Topology Star

Network Cables Ethernet: 2-pair UTP Cat. 3,4,5 , EIA/TIA- 568 STP

Fast Ethernet: 2-pair UTP Cat. 5, EIA/TIA-568 STP

Gigabit Ethernet: 4-pair UTP Cat.5, EIA/TIA-568 STP

LED Indicator 10M Link, 100M Link, 1000M Link, Activity

Full-duplex / Collision

RJ-45 Port Auto MDI-II/MDI-X port

Physical and Environmental

Power Consumption 4.3 watts. (max.)

Temperature Operating: -10°~ 40°C, Storage: -10°~ 70°C

Humidity Operating: 10% ~ 90%, Storage: 5% ~ 90%

Dimensions 59 x 120 x 15mm (W x D x H)

EMI: FCC Class B, CE Mark B, VCCI-B

Table of contents

Other TRENDnet Network Card manuals

TRENDnet

TRENDnet TFM-CF56 User manual

TRENDnet

TRENDnet TEW-501PC User manual

TRENDnet

TRENDnet TEW-647GA User manual

TRENDnet

TRENDnet TE100-PCBUSR - DATA SHEETS User manual

TRENDnet

TRENDnet TEG-PCISX User manual

TRENDnet

TRENDnet TEW-PC16 User manual

TRENDnet

TRENDnet TEG-PCITX2 User manual

TRENDnet

TRENDnet TEG-PCITXR User manual

TRENDnet

TRENDnet TEW-421PC User manual

TRENDnet

TRENDnet TEW-637AP - 300Mbps Wireless Easy-N-Upgrader User manual

TRENDnet

TRENDnet TPL-430AP User manual

TRENDnet

TRENDnet TE100-PCIWS User manual

TRENDnet

TRENDnet TEW-222CF User manual

TRENDnet

TRENDnet TEW-641PC User manual

TRENDnet

TRENDnet WN8020B User manual

TRENDnet

TRENDnet TEW-642EC User manual

TRENDnet

TRENDnet TEG-PCITX User manual

TRENDnet

TRENDnet TEG-PCITX User manual

TRENDnet

TRENDnet TPA-311 User manual

TRENDnet

TRENDnet TEG-PCITXR User manual

TRENDnet

TRENDnet TEG-PCITXRL User manual

TRENDnet

TRENDnet TE100-PCIA User manual

TRENDnet

TRENDnet TEW-202CF User manual

TRENDnet

TRENDnet TPL-410APK User manual

Popular Network Card manuals by other brands

FirstComm

FirstComm OBiWiFi5G Setup guide

Sun Microsystems

Sun Microsystems Interface Adapter user guide

YASKAWA

YASKAWA SI-EN3 Technical manual

Paradyne

Paradyne BitStorm 2600 IP DSLAM installation guide

Belkin

Belkin F5D7050 user manual

3Com

3Com EtherLink 3C509B quick guide

Cisco

Cisco MC16E installation guide

Delta Electronics

Delta Electronics Braking Modules VFDB Series instruction sheet

TwinMOS

TwinMOS Booming user manual

Dialogic

Dialogic Media Board DM/V1200BTEPEQ installation guide

Buffalo

Buffalo AirStation WLI-PCM-L11GP user manual

National Instruments

National Instruments NI 9234 operating instructions

Hama

Hama 49276 Operating instruction

Linksys

Linksys WCF54G - Wireless-G Compact Flash Card Product data

Compaq

Compaq Wireless LAN 100 specification

Bose

Bose PowerMatch Dante quick start guide

Gigafast

Gigafast EE101-AEX user manual

D-Link

D-Link DHP?P309AV Setup guide