Tranquil Ease MCHR-585 Series User manual
Tranquil Ease®Sensation Massage Chair
MCHR-585 Series
User Manual
TABLE OF CONTENTS
Thank you for purchasing the TE Sensation massage chair from Raffel Comfort Sciences. We are confident
that you will find this product to be among the best available.
Diagram of Chair 2
Installation Instructions 3-5
Remote Control Diagrams 5-6
Basic Operating Instructions 6-14
Maintenance and Precaution 15
Warranty 15-16
Description: Specifications:
Model number of the Product MCHR-585
Power source AC 110-120v
Alternating current 60Hz
Power consumption 200W/Heat power:25w
Timer 5/10/15/25/30 minutes
Maximum operating period 90 minutes
Dimension (Length/width/height) Shipping size: 52×30×33.5(inches)
Horizontal size: 78×30×32(inches)
Vertical size: 51×30×48(inches)
Weight
Product gross weight: 235 lbs.
Product net weight: 185 lbs.
Length of the wire Controller wire: 4 ft.
Power supply wire:7 ft.
Usage condition Environment temperature: 50°-104° F
Contrasting humidity: 30-85RH
Storage condition Storage temperature: 68°-140° F
Storage humidity level: 30-85RH
Safety features Equipped with overheated and power surge safety
protection
User benefits Increases blood circulation
Relieves muscular fatigue
Before installation, unfold the Backrest as shown below.
SET UP GUIDELINES
- 2 -
- 3 -
- 4 -
Connect to the power supply, and turn the switch under the Seat Pad to: “I” position, the Backrest will slowly come upright
approximately 5seconds later. The Chair is now in idle mode, During its idle mode, there are only five functions; ON/OFF, Backlight,
Recline, Sit Up ,Lift Leg or Recline Leg” that can be operated.
Diagram of Remote Control Panel
- 5 -
Diagram of Inner Control Panel
Connect to the power supply, and turn the switch under the Seat Pad to: “I” position, the Backrest will slowly
come upright approximately 5seconds later. The Chair is now in idle mode, During its idle mode, there are only
five functions; ON/OFF, Backlight, Recline, Sit Up ,Lift Leg or Recline Leg” that can be operated.
Control Buttons for the Massage Chair
1. ON/OFF
The Start/Stop Control Button
Press once on this button and the backlight of the Remote Control will start blinking: the chair is in idle mode.
Press any massage function button to begin massage functions on the chair. This will also start the Timer.
Press this button again to stop all massage functions. The massage rollers will return to its original position.
2/3 Recline/Sit Up
Angle Adjustment Control Button for Massage Chair
These two control buttons can adjust the Reclining/Sit Up angle respectively. Press once on the Reclining or Sit
Up control button to adjust the Backrest and Footrest to a comfortable position. Press any of the control buttons
again to adjust for Reclining, Sit Up, Lift Leg, Recline Leg to confirm the position.
4/5 Lift Leg/Recline Leg
Angle Adjustment Control Button for Calves
These two control buttons can adjust massage angle on the Leg rest. Press once on the Lift Leg or Recline Leg
control button, the Leg rest will adjust itself to a comfortable position, and then press any of the control buttons
again for Reclining, Sit Up, Lift Leg or Recline Leg to confirm the position.
6. Timer
The Timer’s Time Interval
After the massage process is activated, the chair will be automatically set on a 15-minute Timer. Subsequently,
every time the “TIMER” button is pressed, the Timer’s interval will be changed in the sequence of
“20>25>30>5>10>15” minutes.
- 6 -
- 7 -
! When there is only 1 minute remaining in the set time, the Backlight of the Remote Control will light up
automatically, followed by 5 beeps to alert the user.
7 Backlight
The ON/OFF Control Button of the Backlight on the Remote Control
Every time this button is pressed, it will change the condition of the Backlight of the Remote Control is the
sequence of “ON>>OFF” or “OFF>>ON”. When the Backlight is turned on, press this button again, and the
Backlight will go off after 2 minutes.
Remarks: Before the Backlight function is activated, pressing any function button can also activate the
Backlight, and the light will go off with a 30-second delay this way.
Control Buttons for the Massage Chair:
8 Pause
The Pause Button
When the chair is in massage mode and the user wants to temporarily pause it, press the Pause button and all
massage functions will stop. The “Pause” icon will be blinking on the Liquid Crystal Display and the set time
countdown will be paused as well. The chair is now in idle mode. Only the “Pause, Backlight, Recline, Sit
Up, Lift Leg, Recline Leg” can be used Press the Pause button again to immediately cease the “Pause”
function and resume the original massage function. The countdown continues.
9. Auto Scan
The Back Massage Auto Scan Button
The chair is equipped with an Auto Scan function that can be adjusted according to the user’s height for a more
effective massage; this is because the position of the user’s neck, shoulder, back and waist all differs with
each individual. At the same time, the Upward./Downward manual control button helps to provide more
precise massage at the exact point for a more effective and in-depth massage.
Every time this button is pressed, the Auto Scan will scan the body and detect the best massage strength. When
the best massage strength is detected, the Massage Rollers will stop at that position, and the machine beeps
once, the Auto Scan is then completed 5 seconds later.
10/11 The Back Massage Up/Down Level Adjustment Button
For a more comprehensive and comfortable massage, the user can further adjust the height of massage by
pressing the Button within 5 seconds after the beeps. The Massage Rollers will go upwards or downwards
according to your request until you reach your most suitable position .The massage request is set when you let
go of the button and the manual adjustment is achieved.
!
i. It is suggested that the Backrest has to be adjusted to the best angle in order to achieve the most accurate
body scan.
ii. Please sit upright and relax during the process of scanning for the most accurate scanning result.
iii. All four Auto Programs – Healthcare, Relax, Therapy, and Smart are equipped with Auto Scan function,
for please refer to the “Auto Program” section.
1. When the Auto Program for the entire body or localized massage is operating, the strength of the air
pressure can be adjusted by pressing the Back & Seat Intensity Control Button.
2. After activating the Auto Program, both the Vibration and Heat function for the back can be activated
according to individual needs.
A. Full Body Auto Program
If one of the four Auto Programs is activated before the Auto Scan of the entire body, the machine will
automatically do a height scan for the back. At the same time the user can manually adjust the massage
height to the preferred level.
The following are the Auto Programs available:
- 8 -
12 Healthcare
13 Therapy
14 Relax
15 Smart (The Backrest and Footrest will resume to the original position when this Auto Program is about to
end
B. Localized Auto Program
This program gives precise massage at the exact part of the body for better localized-massage effect.
16 Full Body:
Full Body Massage Start / Stop Control Button.
17 Neck / Shoulder:
Neck / Shoulder Auto Program Start / Stop Control Button
18 Back / Lumbar:
Back / Lumbar Auto Program Start / Stop Control Button
19 Seat:
Auto Air Fill / Vibration for the seat Auto Program Start / Stop Control Button
20 Calves:
!Auto Air Fill / Vibration for the seat Auto Program Start / Stop Control Button
The Auto Program of Full Body, Neck / Shoulder, Back / Lumbar can be combined with the Auto Program
of Seat and Calves for richer Full Body Auto Massage mode.
21 Tapping
Tapping function Start / Stop Control Button-2 types of modes, 3 sizes of width, 3 levels of strength to be
adjusted.
Press once on Tapping 1(or Tapping 2), the Tapping mode can be changed by pressing Tapping 2 (or
Tapping 1).
22 Clap
Clap function Start / Stop Control Button -2 types of modes, 3 sizes of width,3 levels of strength to be
adjusted.
Press once on Clap 1(or Clap 2) to activate the Clap mode for full back-massage at medium speed; press
again to stop the Clap function.
After activating Clap 1 (or Clap 2), the Clap mode can be changed by pressing Clap 2 (or Clap 1)
23 Shiatsu
Shiatsu function Start / Stop Control Button – 2 types of modes, 3 sizes of width,3 levels of strength to be
adjusted.
Press once on Shiatsu 1 (or Shiatsu 2) to activate the Shiatsu mode for full back-massage at medium speed;
press again to stop the Shiatsu function.
After activating Shiatsu 1 (or Shiatsu 2), the Shiatsu mode can be changed by pressing Shiatsu 2 (or Shiatsu
1).
- 9 -
24 Speed
The Speed Adjustment button for Tapping, Clap and Shiatsu mode
After activating the Tapping, Clap or Shiatsu function, every time the button is pressed, the strength can be
adjusted from the cycle of “Strong> Weak> Mild”.
25 Width
The Width Adjustment button for Tapping, Clap, Shiatsu, Rolling mode
After activating the Tapping, Clap, Shiatsu or Rolling function, every time the button is pressed, the width
can be adjusted from the cycle of ”Wide> Narrow> Medium”.
26 Rolling
Rolling function Start / Stop Control Button -3 sizes of width.
Press this button once and it will activate the Rolling function for full back massage. Press again to stop the
function.
This function cannot be used to perform “Spot” massage.
Setting Spot or Localized Back Massage
27 Spot
The Spot or Localized Back massage
This button allows user to select Spot massage for any part on the back by pressing the Upward /
Downward button and the position for Spot massage can be adjusted to suit the user needs.
Press this button once to activate spot massage while the original massage mode continues to run at the
original position. Press again to cease Spot massage function and resume full back massage function.
28 Partial
The Partial Back Massage
This button allows user to select Partial Massage for any part of the back by pressing the Upward /
Downward button. The position for Partial Massage can be adjusted for a user friendly method of Localized
Massage.
Press this button once to continue the original massage mode, while activating Partial Massage, which takes
the original position as the centre to perform Partial Massage with the width of approx. 8 cm. Press again to
stop Partial Massage function and resume full back massage function.
▲/ ▼
29/30 The Position Adjustment button for Spot or Partial Massage
After activating Spot or Partial Massage, continue to press the ▲/ ▼buttons in succession to move the
massage. Te Massage Rollers will go upwards or downwards until the desired position. The original
position of the Spot or Partial Massage will be shifted to the new position. Release the ▲/ ▼button once
the desired position is achieved.
Setting seat / Leg Vibration
31 Vibration
Vibration function Star / Stop Control Button – 2 types of modes to be adjusted. Press once on Vibration 1
(or Vibration 2) and it will activate the Vibration mode 1 (or mode 2) function; press this button again and
it will stop the Vibration function.
Setting Seat / Calves / Leg Air-pressure
Table of contents
Other Tranquil Ease Massager manuals
