Tracker GLSY22521 User manual

CAUTION

Read all precautions and instruc-

tions in this manual before using

this equipment. Save this manual

for future reference.

Model No. GLSY22521

Serial No.

Write the serial number in the

space above for future reference.

QUESTIONS?

As a manufacturer, we are com-

mitted to providing complete

customer satisfaction. If you

have questions, or if there are

missing or damaged parts, we

will guarantee complete satis-

faction through direct assis-

tance from our factory.

TO AVOID DELAYS, PLEASE

CALL DIRECT TO OUR TOLL-

FREE CUSTOMER HOT LINE.

The trained technicians on our

customer hot line will provide

immediate assistance, free of

charge.

CUSTOMER HOT LINE:

1-800-999-3756

Mon.–Fri., 6 a.m.–6 p.m. MST

Patent Pending

USER’S MANUAL

Serial Number Decal (Under Seat)

WARNING DECAL PLACEMENT

WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover

Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the center of

this manual. Remove the PART IDENTIFICATION CHART and PART LIST/EXPLODED DRAWING before begin-

ning assembly.

TRACKER, a registered trademark of Galyan’s Nevada Inc., East Main St., Plainfield, IN 46168

TABLE OF CONTENTS

The decals shown here have been placed on the

weight system. If a decal is missing or illegible,

please call our Customer Service Department

toll-free at 1-800-999-3756, Monday through

Friday, 6 a.m. until 6 p.m. Mountain Time, to

order a free replacement decal. Apply the decal

in the location shown.

Decal 1

Decal 2–

This decal is on the finger guards

on both sides of the weight bench.

• Misuse of this

product may result in

serious injury.

WARNING

• Read user’s manual

and follow all warnings

and operating instruc-

tions prior to use.

• Replace label if

damaged, illegible,

or removed.

• Do not allow children

on or around machine.

Keep hands and

fingers clear of

this area.

Decal 1

Decal 2

1. Read all instructions in this manual before

using the weight system. Use the weight sys-

tem only as described in this manual.

2. It is the responsibility of the owner to ensure

that all users of the weight system are ade-

quately informed of all precautions.

3. The weight system is intended for home use

only. Do not use the weight system in any

commercial, rental, or institutional setting.

4. Use the weight system only on a level sur-

face. Cover the floor beneath the weight sys-

tem to protect the floor.

5. Make sure all parts are properly tightened

each time you use the weight system.

Replace any worn parts immediately.

6. Keep children under 12 and pets away from

the weight system at all times.

7. Keep hands and feet away from moving parts.

8. Always wear athletic shoes for foot protec-

tion while exercising.

9. Make sure that the cables remain on the pul-

leys at all times. If the cables binds as you

are exercising, stop immediately and make

sure that the cables are on the pulleys.

10. Always set both safety spotters at the same

height.

11. The weight system is designed to support a

maximum user weight of 250 pounds, and a

maximum total weight of 560 pounds. Do not

place more than 310 pounds on the barbell.

Do not place more than 150 pounds on the

weight carriage or the leg lever. Note: The

weight system does not include weights.

12. Always place an equal amount of weight on

each side of the weight carriage or barbell.

13. Always secure the weights with the weight

clips when they are mounted on the weight

carriage.

14.

Always exercise with a partner. Your partner

should be ready to catch the barbell if you

cannot complete a repetition.

15. Always move the bench out of the way when

performing squat exercises. Always discon-

nect the lat bar from the cable when perform-

ing an exercise that does not require it.

16. If you feel pain or dizziness at any time while

exercising, stop immediately and begin cool-

ing down.

WARNING:Before beginning this or any exercise program, consult your physician. This

is especially important for persons over the age of 35 or persons with pre-existing health problems.

Read all instructions before using. ICON assumes no responsibility for personal injury or property

damage sustained by or through the use of this product.

WARNING: To reduce the risk of serious injury, read the following important precautions

before using the weight system.

IMPORTANT PRECAUTIONS

ASSEMBLED

DIMENSIONS:

Height: 84 in.

Width: 83 in.

Depth: 96 in.

Weight Carriage

Upright

Smith Bar Guide

Safety Spotter

Locking Bar

Barbell

Butterfly Arm

Backrest Bracket

Right Side

Left Side

Note: The terms “right side” and “left side” are determined relative to a person sitting on the

bench; they do not correspond to right and left on the drawings in the manual.

Curl Pad

Backrest

Foot Plate

Leg Lever

Seat

Lat Bar

BEFORE YOU BEGIN

Thank you for selecting the versatile TRACKER®735

POWER SMITH SYSTEM weight system. The weight

system is designed to help you develop every major

muscle group of the body. Whether your goal is a

shapely figure, dramatic increase in muscle size and

strength, or a healthier cardiovascular system, the 735

POWER SMITH SYSTEM weight system will help you

achieve the specific results you want.

For your benefit, read this manual carefully before

using the weight system. If you have additional ques-

tions, please call our Customer Service Department

toll-free at 1-800-999-3756, Monday through Friday,

6 a.m. until 6 p.m. Mountain Time (excluding holidays).

To help us assist you, please note the product model

number and serial number before calling. The model

number is GLSY22521. The serial number can be

found on a decal attached to the weight system (see

the front cover of this manual).

Before reading further, please review the drawing

below and familiarize yourself with the parts that are

labeled.

Before beginning assembly, carefully read the

following information and instructions:

•Assembly requires two people.

•Place all parts in a cleared area and remove the

packing materials. Do not dispose of the packing

materials until assembly is completed.

•Tighten all parts as you assemble them, unless

instructed to do otherwise.

•As you assemble the weight system, make sure

all parts are oriented as shown in the drawings.

•For help identifying small parts, use the PART

IDENTIFICATION CHART.

The following tools (not included) are required

for assembly:

•Two adjustable wrenches

•One rubber mallet

•One standard screwdriver

•One Phillips screwdriver

•Lubricant, such as grease or petroleum jelly,

and soapy water.

Assembly will be more convenient if you have a

socket set, a set of open-end or closed-end

wrenches, or a set of ratchet wrenches.

Make Things Easier for Yourself

Everything in this manual is designed to ensure

that the weight system can be assembled suc-

cessfully by anyone. However, it is important to

realize that the versatile weight system has

many parts and that the assembly process will

take time. Most people find that by setting aside

plenty of time, assembly will go smoothly.

ASSEMBLY

Press a 51mm x 76mm Inner Cap (21) into the

Front Leg (4). Attach two Stabilizer Feet (22) to

the Front Stabilizer (3) with four M4 x 16mm

Screws (103).

Attach the Front Leg (4) to the Front Stabilizer (3)

with four M10 x 68mm Bolts (26), two Leg Plates

(41), and four M10 Nylon Locknuts (32). Do not

tighten the Locknuts yet.

2. Attach two Stabilizer Feet (22) to the Rear

Stabilizer (1) with four M4 x 16mm Screws (103).

Attach the two Wheels (38) to the Rear Stabilizer

(1) with two M10 x 45mm Bolts (27) and two M10

Nylon Locknuts (32). Do not overtighten the

Locknuts; the Wheels must be able to roll

easily.

Attach the Bench Frame (2) to the Rear Stabilizer

(1) with two M10 x 68mm Bolts (26), two M10

Washers (100), and two M10 Nylon Locknuts

(32). Make sure the decal is in the indicated

position. Do not tighten the Locknuts yet.

103

22 41

32 38

38 100

26 27

127

103

Decal

103

Before beginning assembly, make sure you

understand the information in the box

above.

5. Attach the Backrest (10) to the Backrest Frames

(6) with four M6 x 53mm Bolts (29) and four M6

Washers (37). Note: If the four Bolts cannot be

inserted into the Backrest properly, go back to

step 4 and readjust the Backrest Frames.

4. Press four 20mm x 40mm Inner Caps (20) into

the ends of the two Backrest Frames (6).

Attach the Backrest Frames (6) to the Backrest

Bracket (9) with four M10 x 58mm Bolts (33), four

M10 Washers (100), and four M10 Nylon

Locknuts (32). Make sure the Backrest Frames

are oriented as shown. The Backrests Frames

must be parallel, with the indicated holes

aligned.

39 34

100

Holes

3. Press two Bushings (34) into the Bench Frame

(2).

Attach the Bench Frame (2) to the Front Leg (4)

with four M10 x 94mm Bolts (18), two Joint Plates

(39), and four M10 Nylon Locknuts (32). Do not

tighten the Locknuts yet.

29 30

6. Press four Bushings (34) into the Backrest

Frames (6) as shown.

Secure the Backrest Knob (25) to the Bench

Frame (2). Pull the Knob out as far as it will go.

Slide the Backrest Bracket (9) between the Bench

Frame tubes and engage the Knob into a hole in

the Bracket.

Attach the Backrest Frames (6) and two Finger

Guards (14) to the Bench Frame (2) with an M10

x 146mm Bolt (35), two M10 Washers (100), and

an M10 Nylon Locknut (32). Make sure the

decals are on the outside of the Finger

Guards. Do not overtighten the Locknut; the

Bracket Frames and Finger Guards must be

able to pivot easily.

8. Press two Bushings (34) into the Seat Frame (5)

as shown.

Attach the Seat Frame (5) to the Backrest

Frames (6) and Finger Guards (14) with an M10 x

146mm Bolt (35), two Short Spacers (36), and an

M10 Nylon Locknut (32). Do not overtighten the

Locknut; the Seat Frame must be able to pivot

easily.

Attach the Pivot Bracket (15) to the Bench Frame

(2) with an M10 x 100mm Bolt (28) and an M10

Nylon Locknut (32). Do not overtighten the

Locknut; the Pivot Bracket must be able to

pivot easily.

Tighten the M10 Nylon Locknuts (32) used in

steps 1–3.

7. Press a 38mm x 50mm Inner Cap (112) into the

indicated end of the Seat Frame (5). Press two

Bushings (34) into the Seat Frame as shown.

Attach the Pivot Bracket (15) to the Seat Frame

(5) with an M10 x 75mm Bolt (30) and an M10

Nylon Locknut (32). Do not overtighten the

Locknut; the Pivot Bracket must be able to

pivot easily.

Attach the Seat (11) to the Seat Frame (5) with

two M6 x 16mm Bolts (31), an M6 x 53mm Bolt

(29), and an M6 Washer (37).

100

100 35

Decal

25 2

53436

28 6

14 35

112

9. Press three 50mm Square Inner Caps (88) into

the Leg Lever (7). Press a 51mm Round Inner

Cap (23) into the tube on the Leg Lever.

Slide the two Pad Tubes (16) into the Leg Lever

(7). Slide four Foam Pads (17) onto the ends of

the Pad Tubes. Press four 19mm Round Inner

Caps (19) into the ends of the Pad Tubes.

11.Press a 45mm Square Inner Cap (80) into the

bottom of the Curl Post (12).

Attach the Curl Pad (13) to the Curl Post (12) with

two M6 x 16mm Screws (31).

10. Press two Bushings (34) into the Leg Lever

Bracket (8) as shown.

Attach the Leg Lever (7) to the Leg Lever Bracket

(8) with an M10 x 78mm Bolt (40) and an M10

Nylon Locknut (32). Do not overtighten the

Locknut; the Leg Lever must be able to pivot

easily.

Loosen the Seat Knob (24). Secure the Leg Lever

Bracket (8) in the end of the Seat Frame (5) with

the Knob.

12. Locate the Base (49) with the warning decal

attached to it. Attach two Base Feet (71) to the

Base with four M4 x 16mm Screws (103).

Attach the Base (49) to the indicated side of the

Center Base (48) with two M10 x 78mm Bolts

(40), two M10 Washers (100), and two M10 Nylon

Locknuts (32). Do not tighten the Locknuts yet.

Attach the Center Base (48) to the other Base

(49) in the same manner.

Insert two M10 x 75mm Carriage Bolts (102) up

through the Center Base (48).

13. Press a 60mm Square Inner Cap (82) into the

back of the Rear Base (44).

Attach the Rear Upright (46) to the Center Base

(48) with the two M10 x 75mm Carriage Bolts

(102) and two M10 Nylon Locknuts (32). Do not

tighten the Locknuts yet.

Attach the Foot Plate (45) and the Rear Base

(44) to the Center Base (48) with two M10 x

82mm Bolts (87) and two M10 Nylon Locknuts

(32). Do not tighten the Locknuts yet.

48 40

102

103

Decal

103

100

32 32

102

15. Attach a Smith Bar Guide (50) to a Base (49) with

an M10 x 78mm Bolt (40), two M10 Washers

(100), two 17mm Spacers (89), and an M10

Nylon Locknut (32). Do not tighten the

Locknuts yet.

Attach an Upright (42) to the Base (49) with four

M10 x 78mm Bolts (40), two Angled Rack Joint

Plates (70), and four M10 Nylon Locknuts (32).

Note: The indicated corners of the Joint

Plates are less than 90 degrees. Do not tight-

en the Locknuts yet.

Attach the other Smith Bar Guide (50) and

Upright (42) to the other Base (49) in the same

manner.

108

111

This corner is

not a right angle

40 40 100

100

100 100

14. See the inset drawing. Insert an M10 x 19mm

Bolt (111) into the bracket on the Weight Carriage

(55).

Press two 51mm Round Inner Caps (23) into the

Weight Carriage (55).

Orient the Weight Carriage (55) and Lat Tower

(43) as shown. Slide the Weight Carriage onto

the Lat Tower. Orient the Carriage Stop (52) as

shown and slide it onto the Lat Tower. Attach the

Carriage Stop at the indicated hole with an M8 x

70mm Bolt (108) and an M8 Nylon Locknut (81).

Attach the Lat Tower (43) to the Rear Base (44)

with two M10 x 68mm Bolts (26), four M10

Washers (100), and two M10 Nylon Locknuts

(32). Do not tighten the Locknuts yet.

The front edge

is taller than

the rear edge

Table of contents

Other Tracker Fitness Equipment manuals

Tracker

Tracker 755 POWER CAGE SYSTEM User manual

Popular Fitness Equipment manuals by other brands

NSD

NSD PB-188P user manual

Performance

Performance HyperVibe User instructions

Scalamobil

Scalamobil S27 Operator's manual

Precor

Precor Experience Series Service manual

FYTTER

FYTTER RedMIUM BENCH BE-T6R manual

Taurus

Taurus TF-RK1312 Assembly and operating instructions

Nustep

Nustep T5 Assembly instructions

Precor

Precor CW-507 Assembly guide

Movement

Movement BICEPS Idea owner's manual

Kegel8

Kegel8 V For Men user guide

Skandika

Skandika Styrke II instruction manual

BLK BOX

BLK BOX 21-0122-0B Owner's manual & quick start guide

Stamina

Stamina aeropilates premier 299 owner's manual

SPORTSTECH

SPORTSTECH PBX300 quick start guide

ParaBody

ParaBody Serious Steel 877102 Assembly guide

Weslo

Weslo Gym 650 Gebruikershandleiding

Rebel

Rebel ACTIVE RBA-1011 user manual

4iiii

4iiii FLiiiight owner's manual