TP-Link TL-SG1024 User manual

User Guide

TL-SG1016/ TL-SG1024

16/24-port Gigabit Ethernet Switch

Rev:2.0.0

7106500823

Specifications are subject to change without notice

is a registered trademark of TP-LINK

TECHNOLOGIES CO., LTD. Other brands and product names

are trademarks or registered trademarks of their respective

holders.

No part of the specifications may be reproduced in any form

or by any means or used to make any derivative such as

translation, transformation, or adaptation without permission

http://www.tp-link.com

FCC STATEMENT

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to pro-vide reasonable

protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate

radio frequency energy and, if not in-stalled and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following

measures:

¾Reorient or relocate the receiving antenna.

¾Increase the separation between the equipment and

receiver.

¾Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

¾Consu

lt the dealer or an experienced radio/ TV techni

cian for

help.

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including

interference that may cause undesired operation.

III

Any changes or modifications not expressly approved by the

party responsible for compliance could void the user’s authority

to operate the equipment.

CE Mark Warning

This is a class B product. In a domestic environment, this

product may cause radio interference, in which case the user

may be required to take adequate measures.

Package Contents

The following contents should be found in your package:

¾One TL-SG1016/TL-SG1024 Switch

¾One power cord

¾This User Guide

¾Rubber footpads for Desk-mount

¾Rack-mount kit for installing the switch in a 19-inch rack

Note:

Make sure that the package contains the above items. If any of

the listed items are damaged or missing, please contact with

your distributor.

Safety Notices

Do not use this product near water. Avoid using this product during

an electrical storm. Do not place heavy objects on the switch.

Chapter 1 Introduction of the Product

This chapter describes the features of the TL-SG1016/

TL-SG1024 16/24-port Gigabit Ethernet Switch.

1.1 Overview of the Product

The TL-SG1016/TL-SG1024 16/24-port Gigabit Ethernet Switch

provides you with a high-performance, low-cost, easy-to-use,

seamless and standard upgrade to boost your old network to

1000Mbps. Increase the speed of your network server and

backbone connections make Gigabit a reality. Power users in

the home, ofﬁce, workgroup, or creative production environment

can now move large, bandwidth-intensive ﬁles faster. Transfer

graphics, CGI, CAD, or multimedia ﬁles and other applications

that have to move large ﬁles across the network almost instantly.

The TP-LINK TL-SG1016/TL-SG1024 features a non-blocking

switching architecture that forwards and filters packets at full

wire-speed for maximum throughput, MAC address auto-

learning and auto-aging, IEEE802.3x ﬂow control for full-duplex

mode and backpressure for half-duplex mode. It is compatible

with all 10,100 and 1000Mbps Ethernet devices because it is

standard-based. It protects your existing network investments

while providing you with a straightforward migration path to

faster Gigabit speeds.

The TP-LINK TL-SG1016/TL-SG1024 is plug-and-play and no

configuration is required. Auto MDI/MDI-X cable detection on all

ports eliminate the need for crossover cable or Uplink port. Each

port can be used as general ports or Uplink ports, and any port

can be simply plugged into a server, a hub, a router or a switch,

using the straight cable or crossover cable. Diagnostic LEDs

which display link status and activity, allowing you to quickly

detect and correct problems on the network.

1.2 Features

¾Complies with IEEE802.3, IEEE802.3u, IEEE802.3ab

standards

¾16/24 10/100/1000Mbps Auto-Sense RJ45 ports supporting

Auto-MDI/MDIX

¾All ports Support Full/Half Duplex transfer mode for

10/100Mbps and Full Duplex transfer mode for 1000Mbps

¾Supports IEEE802.3x ﬂow control for full-duplex mode and

backpressure for half-duplex transfer mode

¾Non-blocking switching architecture that forwards and filters

packets at full wire-speed for maximum throughput

¾Supports MAC address auto-learning and auto-aging

¾LED indicators for monitoring power, link, speed and activity

¾Rack-mountable steel case

¾Internal power supply

Chapter 2 Installation

2.1 Mounting the Switch on a Desk

Before place the Switch on a desk, attach four rubber footpads

to the flutes on the Switch bottom, then lay the Switch on the

desktop, where can be have as much as 5kg placed on top.

Note:

1. The electrical outlet shall be installed near the device and

shall be easily accessible.

2. Make sure there is free space for radiating heat and air.

3. Make sure not to place anything too heavy on top of the switch.

2.2 Mounting the Switch in a Rack

The dimension of TL-SG1016/TL-SG1024 is designed according

to the standard 19 rack-mountable steel case of Electronic

Industries Association.

Turn off all the equipment connected to the Switch before

mounting it in the rack, then rivet the two "L" brackets onto each

side of the Switch, fasten it with screws in the rack.

Figure 2-1 Rivet the “L” brackets onto the Switch

Figure 2-2 Fasten the Switch in the rack

2.3 Power On

TL-SG1016/TL-SG1024 16/24-port Gigabit Ethernet Switch is

automatically initialize and its LED indicators should respond as

follows:

1）All of the Link/Act and 1000Mbps LED indicators will ﬂash

momentarily for one second, which represent a resetting of

the system.

2）The Power indicator will light up.

If the LED indicators don't respond as described above, please

check the power supply and connection.

Chapter 3 Identifying External Components

This Chapter describes the front panel, rear panel and LED

indicators of the Switch. TL-SG1016 and TL-SG1024 just differ

in the number of LED indicators and ports and all ﬁgures in this

guide are of TL-SG1024.

3.1 Front Panel

The front panel of the TL-SG1024 consists of switch LED

indicators, 24 10/100/1000Mbps RJ-45 ports.

Figure 3-1 TL-SG1024 Switch Front Panel sketch

3.2 Rear Panel

The rear panel of the TL-SG1024 only features a power

receptacle, which is an AC power receptacle. Connect the

female of the power cord head here, and the male head to the

AC power outlet.

Figure 3-2 TL-SG1024 Switch Rear Panel sketch

3.3 LED Indicators

The LED indicators include Power, Link/Act and 1000Mbps LED

indicators, which are used for monitoring and pre-

troubleshooting of the Switch. The following section shows the

LED indicators for the switch along with an explanation of each

indicator.

Figure 3-3 TL-SG1024 Switch LEDs sketch

¾Power LED: This indicator will light solid red when the

Switch powers up. If the LED is not lit, please check the

power supply and connection.

¾Link/Act LED: This indicator will light solid green when the

corresponding port is connected to another device and will

ﬂash green when data is being transmitted or received on

the working connection.

¾1000Mbps LED: This indicator will light solid green when the

corresponding port is connected to a 1000Mbps device.

Appendix A: Specifications

General

Standards

IEEE802.3 10Base-T

IEEE802.3u 100Base-TX

IEEE802.3ab 1000Base-T

Topology Star

Protocol CSMA/CD

Ethernet: 10Mbps (Half Duplex), 20Mbps

(Full Duplex)

Fast Ethernet: 100Mbps (Half Duplex),

200Mbps (Full Duplex)

Data Transfer

Rate

Gigabit Ethernet: 2000Mbps (Full Duplex)

10Base-T: UTP category 3, 4, 5 cable

(maximum 100m)

EIA/TIA-568 100 STP (maximum 100m)

100Base-TX: UTP category 5, 5e cable

(maximum 100m)

EIA/TIA-568 100 STP (maximum 100m)

Network Media

(Cable)

1000Base-T: UTP category 5, 5e cable

(maximum 100m)

EIA/TIA-568 100 STP (maximum 100m)

Number of Ports 16/24 10/100/1000Mbps Auto-Negotiation

RJ-45 ports

Other manuals for TL-SG1024

This manual suits for next models

Table of contents

Other TP-Link Switch manuals

TP-Link

TP-Link TL-SG608E User manual

TP-Link

TP-Link TL-SG5426 - User manual

TP-Link

TP-Link TL-SF1008P User manual

TP-Link

TP-Link TL-SG605E User manual

TP-Link

TP-Link TL-SG1005D User manual

TP-Link

TP-Link UH720 User manual

TP-Link

TP-Link TL-SG105E User manual

TP-Link

TP-Link TL-SG2216 User manual

TP-Link

TP-Link TL-SX1008 User manual

TP-Link

TP-Link Tapo S500 User manual

TP-Link

TP-Link JetStream T1500G-10MPS User manual

TP-Link

TP-Link JetStream T3700G-52TQ User manual

TP-Link

TP-Link JetStream TL-SG5412F User manual

TP-Link

TP-Link TL-SG1008PE User manual

TP-Link

TP-Link TL-SF1008P User manual

TP-Link

TP-Link JetStream T1600G-52TS User manual

TP-Link

TP-Link TL-SX1008 V1 User manual

TP-Link

TP-Link TL-SG1218MPE User manual

TP-Link

TP-Link JetStream T1500G-8T User manual

TP-Link

TP-Link TL-SF1005D User manual

TP-Link

TP-Link JetStream T1500G-8T User manual

TP-Link

TP-Link JetStream T1500G-8T Installation instructions manual

TP-Link

TP-Link TL-SG105S User manual

TP-Link

TP-Link TL-SG1008PE User manual

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual