TP-Link TL-R402M Manual

Other manuals for TL-R402M

1

Table of contents

Other TP-Link Network Router manuals

TP-Link

TP-Link AXE5400 User manual

TP-Link

TP-Link TD-W8960N User manual

TP-Link

TP-Link TD-W9977 User manual

TP-Link

TP-Link Archer C2600 User manual

TP-Link

TP-Link TL- WR740N User manual

TP-Link

TP-Link TD-W8950ND User manual

TP-Link

TP-Link Archer C7 Setup guide

TP-Link

TP-Link TL-WR940N User manual

TP-Link

TP-Link TL-WR802N User manual

TP-Link

TP-Link Archer A6 User manual

TP-Link

TP-Link Archer C54 User manual

TP-Link

TP-Link Omada ER706W User manual

TP-Link

TP-Link TL-MR3420 User manual

TP-Link

TP-Link OnHub User manual

TP-Link

TP-Link ARCHER C25 User manual

TP-Link

TP-Link Archer AX10 User manual

TP-Link

TP-Link TL-WR702N User manual

TP-Link

TP-Link TL-WR1043ND - Ultimate Wireless N Gigabit... User manual

TP-Link

TP-Link JetStream TL-SL3428 User manual

TP-Link

TP-Link TD-W8960N User manual

TP-Link

TP-Link TL-R470T Plus User manual

TP-Link

TP-Link TPL-WR941HP User manual

TP-Link

TP-Link Deco BE65 User manual

TP-Link

TP-Link JetStream T2600G-28TS User manual

Popular Network Router manuals by other brands

Allnet

Allnet ALL0333AU user guide

HomeSeer

HomeSeer HT-SEL Getting started guide

Sercomm

Sercomm Genesis OC3505D Quick installation guide

Billion

Billion BIPAC 5102 Series user manual

Motorola

Motorola MR1900 user guide

Digi

Digi IX14 user guide

Cisco

Cisco NCS 540 Hardware installation guide

XAVi

XAVi X8821e user manual

BEC

BEC 6200WZL Quick installation guide

MikroTik

MikroTik hAP ac3 Series quick start

Korenix

Korenix JetNet 5428G Series user manual

NETGEAR

NETGEAR FS526T - Switch installation guide

Korenix

Korenix JetNet 5710G Series user manual

Automated Logic

Automated Logic ZN551 Technical instructions

Cisco

Cisco ASR 1000 Series Installation and configuration guide

EnGenius

EnGenius ESR-9710 quick start guide

Cisco

Cisco 805 Series Product overview

LevelOne

LevelOne FBR-1416 user manual

Rev. 1.3 – 01/07/2009

TP Link Router Basic Setup

Introduction

The TP-Link #TL-R402M Cable/DSL Router is a broadband router. Detailed information is on

the vendor’s web site at http://www.tp-link.com.

A router assigns Dynamic Host Configuration Protocol (DHCP). This means the router

assigns Internet Protocol (IP) addresses to all connected equipment configured to request on.

The two basic rules for DHCP:

•Only one router can be active in the same group of connected equipment.

•Each equipment item must have a unique IP address. If two devices get the same IP,

erratic behavior will result – most often the duplicate IP will fail to communicate.

By default, DHCP is on in this router.

Package Contents:

•TP-Link TL-R402M Router

•Power Adapter

•Quick Installation Guide

•Resource CD

You must own or purchase 1 network cable; the most common is a 6 foot

length. While sold under various names, make sure it is Cat5E type, with the

RJ-45 connectors.

Installation Planning

Consult the TP-Link Quick Installation Guide for an overview. The TP-Link TL-R402M unit is a

broadband router, so it must work with your cable or dsl modem. Your existing Cable or DSL

modem must also have one Ethernet port, which is probably connected to your PC.

Double-check that your internet works with the existing Cable or DSL modem before

you try to add the router. If you don’t have functioning internet before proceeding,

contact your Internet Service Provider (ISP).

Rev. 1.3 – 01/07/2009

Home Installation of the TP-Link Router

1. Power down all existing equipment (computer, cable/dsl modem, etc.).

2. Locate a suitable location for the TP-Link router.

3. On your cable or dsl modem, find the Ethernet port

and follow the (network) cable from the port of the

modem to the network card on the PC.

4. Unplug the PC end of the cable, and plug it into the WAN port on the TP-Link router.

[Note: you use the WAN port if you will leave DHCP on and use this device as a router.]

5. Now take the extra Ethernet cable (from page 1), and plug one end into the network port

on the PC (where you just removed your modem’s cable in step 4 above).

6. Plug the other end of the extra cable into any open LAN port on the TP-Link router (see

picture in step #4). Tip: It can keep you organized to use port #1, but this isn’t strictly

necessary.

7. Connect the A/C adapter to the router, and it will power on.

8. Power on the primary PC and the cable/dsl modem.

9. Recheck that your basic internet still works on the PC.

10. Proceed to the Weather Direct gateway installation, if that is your goal

(www.weatherdirect.com).

Note: If you have internet service problems at this point, the two most common errors are:

a) a mistake in the cabling, so check the connections in steps 1-9 again or

b) missing that DHCP is enabled on either the cable/dsl modem or some other routing

device. Only one device can serve DHCP, so competing devices need DHCP disabled.

If you have any additional needs, you will need to consult the TP-Link Users Guide on the CD

that came with the router or our Router Trouble-Shooting handout.

LAN

ports