Torque X-CREATE User manual
XCREATE ANCHORING REQUIREMENTS
AND INSTRUCTIONS
X-CREATE SYSTEMS ARE HEAVY PIECES OF EQUIPMENT. THEY ARE INTENDED TO SUPPORT SIGNIFICANT
WEIGHT DURING ROUTINE USE AND SHOULD BE SECURELY ASSEMBLED AND FASTENED TO A SUPPORTING
SURFACE OF SUITABLE CONSTRUCTION. FAILURE TO TAKE PROPER CARE IN SITE SELECTION, ASSEMBLY OR
INSTALLATION CAN LEAD TO SERIOUS PERSONAL INJURY AND PROPERTY DAMAGE.
Electrical wires, water pipes etc. can be running underneath a oor so understand what is below before
drilling.
Read these instructions carefully before proceeding and follow the installation directions carefully to
minimize the risk of injury or property damage.
REVISION: A
Thank you for your purchase of the Torque Fitness X-Create. The following information will help prepare your
facility and installation provider for the delivery and installation of the selected X-Create conguration.
SECURING Torque Fitness X-Create: X-Create congurations must be anchored directly to structurally
sucient concrete oors to ensure maximum safety and frame rigidity. Failure to secure the system to the
oor could result in toppling, leading to serious injury or death. Failure to secure it to the oor will also allow
it to “walk” or rock while in use. This type of movement is unsafe and could damage the oor surface.
APPROVED ANCHORING SPECIFICATIONS
Concrete Floor: 3 inch thick, 3,000 psi or greater
Minimum anchor embedment depth: 2-1/2 inches.
Anchor option 1: 3/8 to1/2 inch diameter x 3 inch Internally threaded drop-in
Anchor. Grade 5 or higher.
Anchor Option 2: 3/8 to1/2 inch diameter x 3 inch externally threaded concrete
anchor.
Note: Read instructions included with the specic anchors used to
select the proper drill bit diameter and depth. This may vary by
brand and type.
APPROVED ANCHOR EXAMPLE
The following anchor can be found at all major hardware and home improvement stores and has been
tested for use with Torque X-Create Systems.
Approved Anchor and Specications: Tapcon® 11413
3/8 x 3 inch Concrete Anchor
Drill Size: ANSI 5/16 inch
Embedment depth: 2-1/2”
Ultimate Pullout (in 3000 psi concrete): 5,445 lbs
2
REQUIRED TOOLS AND HARDWARE
FOR ANCHORING TO CONCRETE FLOORS
Hammer Drill
ANSI Masonary drill bit
(Reference anchors for correct size)
3/8” x 3” Concrete anchors
3/8”Washers Level
Socket Wrench and Socket
3
ANCHORING LOCATIONS
NOTES
1. Complete assembly of entire frame and position the X-Create where desired prior to
starting the anchoring procedure. Some attachments such as the lower Accessory Trays
may interfere with the drilling operation and should be left o or removed prior to
anchoring. (See page 7 for placement along wall.)
2. Using a level, ensure that the uprights are vertically level.
3. If the concrete oor is covered with padded carpet or rubber, it is recommended that
cutouts be made around the base plates so that the uprights can be mounted directly
to the oor. This will ensure that the system is stable and will reduce shear forces on the
anchors.
4. Each X-Create upright provides eight anchoring locations. In every upright, the front two
and rear two holes are required to have anchors installed. (If embedment depth of 2-1/2
inches is not possible or if the concrete is less than 3000 psi but greater than 2000 psi, use
anchors in all eight holes.)
4
REQUIRED
REQUIRED
OPTIONAL
(ON BOTH SIDES)
(SEE STEP 4)
ANCHORING INSTRUCTIONS
DIRECTIONS
1. Using an ANSI concrete drill bit (reference your hardware for the correct size), drill
approximately a 3”hole (reference hardware for correct depth) through the anchoring
hole in the base plate. (To prevent the drill from contacting the upright, place a piece of
cardboard between the drill casing and the upright)
2. Vacuum all concrete dust from the hole. (Failure to remove all concrete dust may prevent
the anchor from going in all the way)
3. Using a socket wrench, tighten a concrete bolt and washer half way in.
4. Repeat the operation to the remaining anchoring holes in the upright.
5. Perform this procedure one upright at a time, pausing to ensure that each upright is still
vertically level before drilling holes.
5
ANCHORING INSTRUCTIONS
DIRECTIONS (Continued)
6. After the anchors have been partially installed, assemble any remaining X-Create
Components securely to the frame. (Components may be dicult to assemble if the
anchors are fully tightened.)
7. Tighten each anchor in every upright to the recommended torque specications as listed
in the specications for the hardware being used.
8. Install the front and rear rubber boots on each upright using four socket head bolts and
four washers.
6
After completing and before using, check that the all of the anchoring bolts and the frame
bolts are properly tightened. Test the system by having multiple people push it up and away
from themselves to ensure that the frame is securely xed to the oor before training on.
For additional questions, contact Torque Fitness at:
email: service@torquetness.com
Phone:763-754-7533
A
45.08in
1145mm
38.19in
970mm
6.89in
175mm
20.91in
531mm
27.80in
706mm
6.89in
175mm
ANCHORING INSTRUCTIONS
ANCHORING DIMENSIONS FOR PLACEMENT ALONG WALL
For most systems, the X-Create can be located so that the base is right against the wall. Only
a small gap is needed between the wall and the rear base plate to allow room for the rubber
boot. For this situation:
A = 1.125 in (28.6 mm) or greater.
For systems that include the Dip Attachment or Plyo Attachment (XCREATE-DA or XCREATE-
PS) on either end of the system, it is advantageous to allow slightly more room for hand and
body clearance during movements. For this situation:
A = 5.25 in (133.4 mm) or greater.
7
WALL
DIMENSIONS
REPEAT
WALL SPACE SYSTEMS
45.08in
1145mm
27.80in
706mm
6.89in
175mm
6.89in
175mm
B
ANCHORING INSTRUCTIONS
ANCHORING DIMENSIONS FOR BRIDGE SYSTEMS
X-Create Bridge Systems are expandable in 2 foot increments. Shown above is the XCB-
2M-13 which is a 13 foot bridge system. The distance for B on this system is:
B = 117.29 in (2979 mm)
For longer Bridge Systems, simply add 24 inches (610 mm) per 2 foot increase in length to
the Bdimension.
8
BRIDGE SPACE SYSTEMS
Table of contents
Other Torque Fitness Equipment manuals
Torque
Torque TR2-HR-101 User manual
Torque
Torque F9W User manual
Torque
Torque TANK M1 User manual
Torque
Torque XG-FB-101 User manual
Torque
Torque TANK M1 User manual
Torque
Torque TANK User manual
Torque
Torque XGYM-WR-1.0 User manual
Torque
Torque XRACK 5832101-A User manual
Torque
Torque XCREATE-LPDWM User manual
Torque
Torque XCC-103 User manual
Torque
Torque XGYM-WR-3.0 User manual
Torque
Torque XGYM-PR24 User manual
Torque
Torque HBT100 User manual
Torque
Torque XCREATE-SM-101 User manual
Torque
Torque XGYM-LSR User manual
Torque
Torque XCREATE-4SRM User manual
Torque
Torque XGYM-LSR Series User manual
Torque
Torque 5854101-B User manual
Torque
Torque 21400 User manual
Torque
Torque X-GYM POWER RACK 5.0 User manual
