Tontex CY-100X User manual
Thank you for purchasing the company's products, in order to better
understand this product, please read this manual carefully.
Product Specifications：
Operating voltage range: AC 200~240V 50Hz Range of working temperature：-20℃~+55℃
Relative humidity range：20%~90% Lifting motor power: 280W (MAX)
Touch screen working power：2W Ratio of display on screen：16:9/4:3/16:10
Sensing resolution：26500x14900 Sensing accuracy：< 0.1mm
Dots per second：120dot/sec Transmission interface：USB/RF2.4G
Transmission speed：9600bps Transmission distance：> 5M
Pen sensing height：>10MM Battery for pen：AAA battery
Dimension of product: Find page H1*L1 Dimension of projection: Find page H2*L2
★Schematic diagram：
★Cautions：
1. When the screen is not in use, please rewind the screen back to the shell, the
roll should pay attention to check the screen to ensure that no worms, dust-free and
other foreign matter before rewinding.
2. The operation of the screen can be rolled up and down continuously in 4 minutes,
otherwise will overheat the motor. At this time, the motor will automatically enter
the protection state to stop running. If it needs to be continuously used, it must
wait for the motor to cool (about 10-15 minutes) then use again.
3. In order to ensure the projection effect of this product, please pay attention
to the following operations.
3.1、Please do not touch the screen by hand.
3.2、Please do not scratch the screen with hard objects such as metal.
3.3、Please use a clean cloth or a soft brush to gently remove the foreign matter
on the screen.
★Hanging installation 1（Standard installation method, the overall blackboard
thickness of less than 11CM with this installation method）：
1、Touch screen projection installation hole size: Description: screen height must
be sure that each row of personnel can clearly see the contents of the projection screen,
the bottom of the screen is generally 0.8 meters from the ground (when the curtain
is fully expanded, the bottom of the display area should be basically higher than the
sitting staff's head, the height of the screen must be sure that each row of personnel
can clearly see the projection screen content, installation company conference room
and specific environment, according to venue to consider). According to the size of
the following figure set the hanger installation location, hang the touch screen to
put down the screen and then set the magnet bracket position, as shown: (Please pay
attention to the projector installation location)
Hoisting schematic diagram：
Magnet mounting method:
2、Touch screen projection screen hanger installation icon：
Picture 2：Picture 3：
3、Hanging touch projection screen: First hang the hook hanging in the projection screen
hanging hole,and the position of the four hook screws fixed. As shown:
Picture 4：Picture 5：
4、Hang the touch projection screen, and adjust the distance between the touch
projection screen and the wall to 120 mm. Tighten the hook screws.
Picture 6：
5、Clean the touch screen projection screen above the host tape, special attention
should be paid, keep the bottoms of the curtain rod and touch layer bar into a free
vertical state to ensure that the projection screen and the touch layer free to lift.
Picture 7：
6、Plug in the power, press the lift switch, down the projection screen and the sensor
layer, please observe whether there is pause problem, if abnormal, please close the
projection screen, after troubleshooting, put down the projection screen and sensor
layer.
Picture 8：
7、Fix the position of the magnet holder according to the position of the axis of the
projection screen. Find the appropriate position on the wall to mark, punch and install
the magnet holder.
Picture 9：
★Hanging installation 2（Blackboard overall thickness of more than 11CM with
this installation method）：
1、Touch projection screen installation Punch size: Description: screen height
to determine the method, the screen as the power is on and stretched, the bottom of
the white iron from the bottom of chalkboard slot distance 2CM.（Magnet rack is too
long to draw the curtain, too short the curtain can not stretch）
Hoisting schematic diagram：
Magnet bracket installation schematic diagram：
Please confirm the floor height is
sufficient before using this
installation method.
★Wall-mounted installation（No blackboard recommended this installation
method, no need the L-shaped hanger）：
1、No matter what kind of installation, please first according to the measurement
of the installation location, confirm the installation height, distance and projection
of the central location, after the installation location to make the installation of
accessories on the wall hole horizontal position, and use the pencil to make the
horizontal line or mark, and then hit the mounting hole.
Picture 1
Picture 2. Against wall installation example：
with podium the height from the ground is
80cm ，without podium the height from
ground is 100cm
Magnet mounting method：
2、After installing the hole on the wall, install the rubber stopper to insert the
rubber stopper into the wall hole with the hammer. The end of the rubber stopper should
be flat with the wall and can not be exposed. Then, screw the screw head at a distance
of about 5 mm from the wall so as to hang Touch projection screen.
Picture 3
3、Hanging the touch projection screen, please pay attention to whether the solid,
clean the touch screen projection screen above the host tape, special attention should
be paid, keep the bottoms of the curtain rod and touch layer bar into a free vertical
state to ensure that the projection screen and the touch layer free to lift. Plug in
the power, press the lift switch, down the projection screen and the sensor layer,
please observe whether there is pause problem, if abnormal, please close the projection
screen, after troubleshooting, put down the projection screen and sensor layer.
★Touch projection screen
fitboard
software installation：
1、Turn on the computer, projector, put down the touch projection screen (keep the switch
DOWN state), and computer startup is completed. As shown：
This manual suits for next models
5
Table of contents
