Tone CSS60-BTL User manual

MODEL
CSS60-BTL / CSS90-BTL / CSS110-BTL
CAUTION
Read and fully understand all the instructions before use.
Keep this manual in designated place for easy and quick reference.
The models mentioned on this manual are designed for use outside Japan.
Warranty shall be void if above mentioned models are use in Japan.

- 1 -
PREFACE
Thank you for purchasing .
■Please confirm the following contents upon receipt of the product.
- During transportation, confirming the product for any damaged parts..
-Confirming that screws and bolts have not dropped and loosened in any part of
the product.
- Confirming that the product is the model number/specification as ordered
- Confirming that all accessories are completed. (➭P. 16).
If there are any problems, please contact the distributor where you purchased the
product.
■Read this instruction manual carefully before use.
A full understanding of the manual is essential to prevent personal injury
or malfunction.
■Keep this manual in a bag attached to the back of the metal case lid for
easy and quick reference.
■If the manual or warning label is lost or becomes illegible, or if an
additional manual is required, please contact the distributor where you
purchased the product.
If you have any questions about the product you have purchased or the
contents of the instruction manual, please contact the distributor where you
purchased the product.
■This manual is only applicable outside Japan.

- 2 -
SAFETY INSTRUCTION
This manual specifies three (3) basic safety instructions:
■Instructions are classified by degree of risk and described as follows:
Danger is used to indicate threatening
dangerous or unsafe practices which could
immediately result in severe personal injury
or death in the worst case.
Warning is used to indicate hazardous or
unsafe practices which could result in severe
personal injury or death in the worst
occasion.
Caution is used to indicate hazardous or
unsafe practices which could result in
personal injury or product or property
damage.
Even if the risk is classified as , risk could become more serious result
depending on conditions. Make sure to follow all instructions when using.

- 3 -
TABLE OF CONTENTS
1.GENERAL SAFETY INSTRUCTIONS ・・・・・・ 5
2.APPLICATION ・・・・・・・・・・・・・・・・・・・・・・・・ 8
3.PRECAUTIONS FOR USE ・・・・・・・・・・・・ 8
4.NAME OF PARTS AND ACCESSORIES・・・・・ 16
5.BEFORE USE ・・・・・・・・・・・・・・・・・・・・・・・・ 17
6.PRECAUTIONS FOR USE LITHIUM -ION
BATTERIES ・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 18
7.INSTALLATION/REMOVAL OF STORAGE
BATTERY ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・22
8.REMAINING BATTERY LEVEL・・・・・・・・・・・23
9.PRECAUTIONS FOR WORK・・・・・・・・・・・・ 24
10.OPERATING PROCEDURE ・・・・・・・・・・・ 24
11.SOCKET REPLACEMENT・・・・・・・・・・・・・・ 26
12.INSPECTION & MAINTENANCE ・・・・・・・・ 28

- 4 -
13.TRA NSPORT ATIO N O F LIT HI UM -IO N
B A T T E R I ES・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ 3 0
14.STORAGE OF LITHIUM-ION BATTERIES・・・31
15.FAILURE DIAGNOSIS・・・・・・・・・・・・・・・・・ 32
16.FEATURES・・・・・・・・・・・・・・・・・・・・・・・・・・・32
17.SPECIFICATIONS ・・・・・・・・・・・・・・・・・・ 33
18.AFTERSALES SERVICE ・・・・・・・・・・・・ 34

- 5 -
1. GENERAL SAFETY INSTRUCTIONS
WARNING
When using electric tools, basic safety precautions, including the following, should
always be followed to reduce the risk of fire, electric shock and personal injury.
Read all these instructions before operating this product and keep these
instructions.
SAVE THESE INSTRUCTIONS
1) Work area
a) Keep work area clean and well lit. Cluttered and dark areas invite
accidents.
b) Do not operate power tools in explosive atmospheres, such as in
the presence of flammable liquids, gases or dust. Power tools create
sparks which may ignite the dust of fumes.
c) Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way.
Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering
a power tool will increase the risk of electric shock.

- 6 -
3) Personal safety
a) Stay alert, watch what you are doing and use common sense
when operating a power tool. Do not use a power tool while you are tired
or under the influence of drugs, alcohol or medication.
A moment of inattention while operating power tools may result in serious
personal injury.
b) Use safety equipment. Always wear eye protection. Safety equipment
such as dust mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce personal injuries.
c) Avoid accidental starting. Ensure the switch is in the off position
before plugging in. Carrying power tools with your finger on the switch
or plugging in power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may
result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times.
This enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewelry or
long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used. Use of these
devices can reduce dust related hazards.

- 7 -
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off.
Any power tool that cannot be controlled with the switch is dangerous and
must be repaired.
c) Disconnect the plug from the power source before making any adjustments,
changing accessories, or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tools
operation. If damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power tools.
f) Use the power tool, accessories and tool bits etc., in accordance with
these instructions and in the manner intended for the particular type of
power tool, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from intended
could result in a hazardous situation.
5) Service
a) Have your power tool serviced by a qualified repair person using
only identical replacement parts. This will ensure that the safety of the
power tool is maintained.

- 8 -
2. APPLICATION
■is an electric tool for tightening
Tension Control Bolt/Nut/Washer assemblies.
3. PRECAUTIONS FOR USE
■To prevent accidents, personal injury, etc., read and follow all instructions listed
below.
■We are not responsible for any accidents caused by using this product on
applications not written on this manual.
■If non-genuine parts are used for this product, it will be judged as a modified
product and all warranties will be invalidating.
DANGER
●Beware of electric shock when operating at the high place.
○Failure to follow this instruction may result in fall down accidents.
WARNING
●Beware of electric shock.
○Never use the wrench under rainy or snowy conditions.
○Never touch the charger plug with wet hands.
Failure to follow this instruction may result in electric shock, fire, or
electric leakage.
●Never use the wrench around the place where gasoline, gas,
thinner, benzene, etc., are stored.
○Do not use the wrench around flammable substances. It may cause an
explosion or fire.

- 9 -
WARNING
●Beware of fall down accidents when working at a high place.
○Wear safety belt
○Provide safety net or canvas as safeguarding against falling items.
○Confirm that no one is underneath the working site before operation.
○Stop operation when physically or mentally tired.
Failure to follow these instructions may result in fall down accidents.
●Avoid overloading.
○Use the wrench and its accessories within the rated specifications.
Overloaded wrench and its accessories may result in a malfunction of
the wrenches, accidents, or personal injury.
●Properly install sockets as described in this manual.
○Incomplete installation may result in accidents and personal injury.
See “SOCKET REPLACEMENT”on page 26.
●Avoid accidental starting.
○Do not put your finger on the switch when carrying the wrench with the
storage battery installed.
○Before inserting the storage battery, make sure that the switch is
turned off. It may start up accidentally and may cause injury.
This manual suits for next models
2
Table of contents
Other Tone Power Tools manuals

Tone
Tone GX361ZA-UC User manual

Tone
Tone CSM160 User manual

Tone
Tone GMC221EZ User manual

Tone
Tone 8-150P User manual

Tone
Tone PW200 User manual

Tone
Tone Power Digitorqon PDX-302N User manual

Tone
Tone SIMPLE TORQON XT-STC7TE User manual

Tone
Tone T6L420NR User manual

Tone
Tone GX361ZA User manual

Tone
Tone GNBC81E-UC User manual






























