toboli 63900 User manual
User’s Manual
Articulated Arm Awning
63900–63905
Illustration similar, may vary depending on model
Please read and follow the operating instructions and safety information prior to initial operation.
Technical changes reserved!
Illustrations, functional steps, and technical data may deviate insignificantly due to continuous further
developments.
© by WilTec Wildanger Technik GmbH Item 63900–63905 Page 2
http://www.toboli.com 01 2023-1
The information contained in this document may alter at any time without prior notice. No part of this
document may be copied or otherwise duplicated without prior written consent. All rights reserved.
WilTec Wildanger Technik GmbH cannot be held liable for any possible mistakes in this operating man-
ual, nor in the diagrams and illustrations shown.
Although WilTec Wildanger Technik GmbH has made every possible effort to ensure that this operating
manual is complete, accurate, and up-to-date, errors cannot be ruled out entirely.
If you have found an error or wish to suggest an improvement, we look forward to hearing from you.
Send us an e-mail to:
or use our contact form:
https://www.wiltec.de/contacts/
The most recent version of this manual in several languages can be found in our online shop:
https://www.wiltec.de/docsearch
Our postal address is:
WilTec Wildanger Technik GmbH
Königsbenden 12
52249 Eschweiler – Germany
To return your goods for exchange, repair, or other purposes, please use the following address. Atten-
tion! To allow for a trouble-free complaint or return, it is important to contact our customer service team
before returning your goods.
Retourenabteilung
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler – Germany
E-mail: service@wiltec.info
Tel: +49 2403 55592–0
Fax: +49 2403 55592–15
© by WilTec Wildanger Technik GmbH Item 63900–63905 Page 3
http://www.toboli.com 01 2023-1
Introduction
Thank you for choosing to purchase this quality product. To minimise the risk of injury, we ask you to
always take some basic safety precautions when using this product. Please read this operating manual
carefully and make sure that you understand it.
Keep these operation instructions in a safe place.
Parts
Part
Name
Part
Name
Part
Name
A
Torsion bar with arm (left)
J
Hand crank
S
Screw M6×40
B
Torsion bar with arm
(right)
K
Awning fabric
T
Screw M6
C
Front bar (right)
L
Valance
U
Screw M8×55
D
Front bar (left)
M
Awning cord
V
Screw M8×55
E
Roller (left)
N
Front bar caps (left,
right)
W
Screw M8
F
Roller (right)
O
Connecting piece
X
Expansion screw
G
Roller connector
P
Plastic bolt for cover
and cord
Y
Wall brackets
H
Front bar connector
Q
Screw 3×10
I
Torsion bar connector
R
Screw 14×15
© by WilTec Wildanger Technik GmbH Item 63900–63905 Page 4
http://www.toboli.com 01 2023-1
Note! The awning over 3.5 m should also include the following parts:
Attention! Awning arms can cause injuries.
© by WilTec Wildanger Technik GmbH Item 63900–63905 Page 5
http://www.toboli.com 01 2023-1
Do not cut the straps of the awning arms until the awning has been completely assembled!
Bad
Right
Assembly
Step 1
Thread the awning cord and cut the cord to the length of the fabric.
© by WilTec Wildanger Technik GmbH Item 63900–63905 Page 6
http://www.toboli.com 01 2023-1
Step 2
Connecting the roller and front bar (left)
© by WilTec Wildanger Technik GmbH Item 63900–63905 Page 7
http://www.toboli.com 01 2023-1
Step 3
Mounting the awning fabric and connecting roller and front bar
© by WilTec Wildanger Technik GmbH Item 63900–63905 Page 8
http://www.toboli.com 01 2023-1
Step 4
1. Plug the connector into the front bar.
2. Insert part P into the front bar and secure with screw Q.
3. Install the bar caps.
1
Left
2
Right
© by WilTec Wildanger Technik GmbH Item 63900–63905 Page 9
http://www.toboli.com 01 2023-1
Step 5
Roll up the awning fabric as tightly as possible.
Step 6
1. Connect the torsion bar, but screw it on later.
2. Insert the roller into the square hole of the gear and the round square of the roller bracket.
3. Connect the two torsion bars and screw them together.
© by WilTec Wildanger Technik GmbH Item 63900–63905 Page 10
http://www.toboli.com 01 2023-1
Step 7
Adjusting the position of the awning
1. Move the arm until it is led through the front bar.
2. Align the bar and arm and tighten the screw O.
3. Then tighten the adjusting screw U up to 90 %.
Step 8
Completing the assembly of the awning
1. You can safely cut the straps that hold the awning arms and torsion bar together. The assembly
of the awning is complete.
2. Now proceed to the wall mounting section.
This manual suits for next models
1
