Thermo Scientific 815 Operating instructions

Visit us online to register your warranty

www.thermoscientific.com/labwarranty

User Manual

Thermo Scientific Precision Model 815

Refrigerated Incubator - Microprocessor Controlled

Operating and Maintenance Manual 7013721 Rev. 2

Thermo Scientific

Manual Number 7013721

2 40096/SI-12271 9/8/16 Updated part number on pg 8-1 from 1900381 to 1890063 ccs

1 40714/IN-4710 2/11/16 Updated 3185052 schematic to 50/60Hz on pg 9-2 ccs

0 40096 4/3/15 Original - new cabinet, cooling On/Off switch, model numbers ccs

Rev ECR/ECN Date Description By

Preface

Refrigerated Incubator i

Catalog/Model Numbers Volume (L/cu. ft.) Voltage

PR505755R / 3721 566/20 115

PR505750R / 3722 566/20 230

PR505750R-CN / 3722CN, 3723 566/20 230

Units covered in this manual:

Thermo Scientificii Refrigerated Incubator

Preface

Contains Parts and Assemblies

Susceptible to Damage by

Electrostatic Discharge (ESD)

CAUTION

Important Read this instruction manual. Failure to read, understand and follow the instructions in this manual

may result in damage to the unit, injury to operating personnel, and poor equipment performance. s

Caution All internal adjustments and maintenance must be performed by qualified service personnel. s

Warning If the incubator is not used in the manner specified in this operating manual, the protection provided

by the equipment design may be impaired. s

Warning Depending on ambient temperature and settings, surface can become warm to touch (up to 60°C). s

Material in this manual is for information purposes only. The contents and the product it describes are subject

to change without notice. Thermo Fisher Scientific makes no representations or warranties with respect to this

manual. In no event shall Thermo be held liable for any damages, direct or incidental, arising out of or related to

the use of this manual.

Thermo Scientific Refrigerated Incubator iii

Preface

Important operating and/or maintenance instructions. Read the accompanying text carefully.

Potential electrical hazards. Only qualified persons should perform procedures associated with this

symbol.

Equipment being maintained or serviced must be turned off and locked off to prevent possible injury.

Marking of electrical and electronic equipment, which applies to electrical and electronic equipment

falling under the Directive 2002/96/EC (WEEE) and the equipment that has been put on the market

after 13 August 2005.

This product is required to comply with the European Union’s Waste Electrical & Electronic

Equipment (WEEE) Directive 2002/96/EC. It is marked with the WEEE symbol. Thermo Fisher

Scientific has contracted with one or more recycling/disposal companies in each EU Member State

European Country, and this product should be disposed of or recycled through them. Further

information on Thermo’s compliance with this directive, the recyclers in your country and

information on Thermo Scientific products will be available at www.thermoscientific.com.

4Always use the proper protective equipment (clothing, gloves, goggles, etc.)

4Always dissipate extreme cold or heat and wear protective clothing.

4Always follow good hygiene practices.

4Each individual is responsible for his or her own safety.

Thermo Scientificiv Refrigerated Incubator

Preface

Do You Need Information or Assistance on

Thermo Scientific Products?

If you do, please contact us 8:00 a.m. to 6:00 p.m. (Eastern Time) at:

1-740-373-4763 Direct

1-800-438-4851 Toll Free, U.S. and Canada

1-877-213-8051 FAX

http://www.thermoscientific.com Internet Worldwide Web Home Page

service.led.marietta@thermofisher.com Tech Support Email Address

Certified Service Web Pagewww.unitylabservices.com

Our staff can provide information on pricing and give you quotations. We canSales Support

take your order and provide delivery information on major equipment items or make

arrangements to have your local sales representative contact you. Our products are listed on the

Internet and we can be contacted through our Internet home page.

Our staff can supply technical information about proper setup, operation orService Support

troubleshooting of your equipment. We can fill your needs for spare or replacement parts or

provide you with on-site service. We can also provide you with a quotation on our Extended

Warranty for your Thermo Scientific products.

Whatever Thermo Scientific products you need or use, we will be happy to discuss your

applications. If you are experiencing technical problems, working together, we will help you

locate the problem and, chances are, correct it yourself...over the telephone without a service

call.

When more extensive service is necessary, we will assist you with direct factory trained

technicians or a qualified service organization for on-the-spot repair. If your service need is

covered by the warranty, we will arrange for the unit to be repaired at our expense and to your

satisfaction.

Regardless of your needs, our professional telephone technicians are available to assist you

Monday through Friday from 8:00 a.m. to 6:00 p.m. Eastern Time. Please contact us by

telephone or fax. If you wish to write, our mailing address is:

Thermo Fisher Scientific (Asheville) LLC

401 Millcreek Road, Box 649

Marietta, OH 45750

International customers, please contact your local Thermo Scientific distributor.

Thermo Scientific Refrigerated Incubator v

Preface

Warranty Notes

Information You Should Know Before Requesting Warranty Service

•Locate the model and serial numbers. A serial tag is located on the unit itself.

•For equipment service or maintenance, or with technical or special application inquiries, contact Technical

Services at 1-800-438-4851 or 1-740-373-4763 (USA and Canada).Outside the USA,contact your local

distributor.

Repairs NOTCovered Under Warranty

•Calibration of control parameters. Nominal calibrations are performed at the factory; typically ±1°Cfor

temperature, ±1% for gases, and ±5% for humidity.Our service personnel can provide precise calibrations as

abillable service at your location. Calibration after awarranty repair is covered under the warranty.

•Damage resulting from use of improper quality water, chemicals or cleaning agents detrimental to

equipment materials.

•Service calls for improper installation or operating instructions. Corrections to any of the following

are billable services:

1)electrical service connection

2)tubing connections

3)gas regulators

4)gas tanks

5)unit leveling

6)room ventilation

7)adverse ambient temperature fluctuations

8)any repair external to the unit

•Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, or improper

installation.

•Repairs to parts or systems resulting from unauthorized unit modifications.

•Any labor costs other than that specified during the parts and labor warranty period, which may

include additional warranty on CO2sensors, blower motors, water jackets, etc.

Section 4

Section 5

Section 6

Section 8

Section 7

Refrigerated Incubator viThermo Scientific

Table of Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1

Unpacking and Damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1

Performance Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

Theory of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

Explanation of Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . .1-3

Explanation of Auxiliary Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4

Instrumentation Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-5

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1

Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2

Operation and Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1

Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1

Symptoms and Possible Causes . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1

Possible Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1

General Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1

Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1

RS232 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1

Setting Up the Incubator for Communication . . . . . . . . . . . . . . . .6-2

Using the Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-5

Setting up the Computer for Communication . . . . . . . . . . . . . . . .6-5

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1

Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-1

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-2

Section 1

Section 2

Section 3

Refrigerated Incubator 1-1Thermo Scientific

Section 1 Introduction

Your satisfaction and safety are important to Thermo and a complete

understanding of this unit is necessary to attain these objectives.

Warning As a routine laboratory precaution, always wear safety glasses

when working with this apparatus. s

This product is not intended, nor can it be used, as a sterile or patient

connected device. In addition, this apparatus is not designed for use in

Class I, II or III locations as defined by the National Electrical Code.

Warning If this equipment is not used as specified in this manual, the

protection provided by the unit design may be impaired. s

Save all packing material until unit is put into service. This merchandise

was carefully packed and thoroughly inspected before leaving our factory.

Responsibility for safe delivery was assumed by the carrier upon acceptance

of the shipment; therefore, claims for loss or damage sustained in transit

must be made upon the carrier by the recipient as follows:

1. Visible Loss or Damage: Note any external evidence of loss or damage

on the freight bill, or express receipt, and have it signed by the carrier's

agent. Failure to adequately describe such external evidence of loss or

damage may result in the carrier's refusing to honor your damage

claim. The form required to file such claim will be supplied by the

carrier.

2. Concealed Loss or Damage: Concealed loss or damage means loss or

damage which does not become apparent until the merchandise has

been unpacked and inspected. Should either occur, make a written

request for inspection by carrier's agent within fifteen (15) days of the

delivery date; then file a claim with the carrier since the damage is the

carrier's responsibility.

If you follow the above instructions carefully, we will guarantee our full

support of your claim to be compensated for loss or concealed damage.

Note Do not - for any reason - return this unit without first obtaining

authorization. In any correspondence to Thermo, supply the nameplate

data, including catalog number and serial number. s

Unpacking and

Damage

Table of contents

Other Thermo Scientific Laboratory Equipment manuals

Thermo Scientific

Thermo Scientific TRACE 1300 User manual

Thermo Scientific

Thermo Scientific Microm HM 430 User manual

Thermo Scientific

Thermo Scientific Finnpipette Novus User manual

Thermo Scientific

Thermo Scientific Dionex ICS-1000 User manual

Thermo Scientific

Thermo Scientific Thermo Scientific 3906 User manual

Thermo Scientific

Thermo Scientific Heratherm IMC 18 User manual

Thermo Scientific

Thermo Scientific CRYO Plus 1 Operating instructions

Thermo Scientific

Thermo Scientific Thermo Scientific SL16 User manual

Thermo Scientific

Thermo Scientific Finnpipette User manual

Thermo Scientific

Thermo Scientific TSQ Series User manual

Thermo Scientific

Thermo Scientific Multidrop Pico 1 User manual

Thermo Scientific

Thermo Scientific ProPac SCX-20 User manual

Thermo Scientific

Thermo Scientific DSQ II User manual

Thermo Scientific

Thermo Scientific RT Basic 12 User manual

Thermo Scientific

Thermo Scientific invitrogen EVOS XL Core User manual

Thermo Scientific

Thermo Scientific VARIOMAG MINI 07 User manual

Thermo Scientific

Thermo Scientific AquaSensors AquaChlor User manual

Thermo Scientific

Thermo Scientific KingFisher Flex User manual

Thermo Scientific

Thermo Scientific Thermo Scientific SL Plus Series User manual

Thermo Scientific

Thermo Scientific STP420D User manual

Thermo Scientific

Thermo Scientific Finnpipette F3 User manual

Thermo Scientific

Thermo Scientific Nicolet iS10 Guide

Thermo Scientific

Thermo Scientific 7450 User manual

Thermo Scientific

Thermo Scientific OWL HEP-1 Operating instructions

Popular Laboratory Equipment manuals by other brands

Qiagen

Qiagen DML 3000 user manual

Queensgate

Queensgate NANOSCAN OP400 Quick start instructions

Conviron

Conviron GEN1000-GE Operator's manual

Parr Instrument

Parr Instrument 4560 Operating instructions manual

IKA

IKA IC control operating instructions

Integra

Integra DOSE IT operating instructions

Agilent Technologies

Agilent Technologies 5800 ICP-OES user guide

Endress+Hauser

Endress+Hauser Cleanfit CPA875 operating instructions

NI PXI-5422 CALIBRATION PROCEDURE

Collomix

Collomix Aqix operating instructions

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series operating manual

Ocean Insight

Ocean Insight FLAME-NIR+ Installation and operation manual

Parker

Parker ALIGN-MG-NA Installation, operation and maintenance manual

BD 644787 user guide

DENTAURUM

DENTAURUM Compact Megaplus Instructions for use

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 instruction manual

VWR

VWR SAS Super IAQ instruction manual

illumina

illumina MiSeqDx reference guide