Thermaltake FANLESS VGA User manual
Note Component
Fanless VGAFanless VGA
>> 01>> 20
Main front
heat sink X1
Main rear
heat sink X1
( Unit : mm )
Nut-C X 3
Thermal
Grease
Thermal grease X 1
Heatpipe X 2
Package A Package B
Screw-A X 3
Screw-B X 3
Front heat
sink base X1
Rear heat
sink base X1
Screw-D X 6 ( for rear heat sink base )
Clip sets X 2
Screw-E X 10 ( for main front and rear heat sink )
Spare parts are included.
*
Package C
Washer X 4
Screws :
Fanless VGA
Exploded Drawing
>> 02
Front heat
sink base
Screw-B
Main rear heat sink
Adhesive tape
Rear heat sink base
Nut - C
Main front
heat sink
Clip set
Screw-A
Screw - D
Screw - E
Screw - E
Heatpipe
Check Point
Fanless VGA
>> 19
1. After completing the Fanless VGA installation, turn on the
computer to check if both of the main heat sink are at
similar temperature range (Leave the computer running
for a few minutes to confirm the temperature and you can
tell the difference by turning the computer off and touch
both of the heatsinks with your hand).
If temperature for both main heat sink seems to differ
greatly, please check the following:
A. Is the thermal grease properly spread onto the following
six areas:
a. On the surface of front heat sink base
b. Inside the tunnel of front heat sink base
c. On the surface of rear heat sink base
d. Inside the tunnel of rear heat sink base
e. Inside the tunnel of main front heat sink
f. Inside the tunnel of main rear heat sink
B. Is the GPU and the front heat sink base tightly in contact?
C. Is the heatpipe properly in contact with the heat sinks?
2. We do not recommend overclocking the video card. We
are not responsible for any damages caused by
overclocking.
3. If the heatpipe is tampered with or scratched by a sharp
object, it may not function properly. Please handle with
care.
4. After successfully installing the video card, do not shake
or exert excessive force on any part of the heat sinks.
The screws and nuts that hold the heat sinks may
become loose.
FANLESS VGA
User's Manual
www.thermaltake.com
Address: Unit 1, 49 Henderson Road Rowville
Victoria 3178 Australia
TEL: +61- (03) 9763 1622 FAX: +61- (03) 9763 1677
URL: www.thermaltake.com.au
Australia: Thermaltake Australia and
New Zealand Pty Ltd
Address: 73, Bld de Courcerin Parc du Courcerin 77185 Lognes
TEL: + 33 - (0)160 1763 15 FAX: + 33 - (0)1 60 17 63 16
France: Thermaltake France
Address: #907,HaiTai Plaza, No.229, North 4th
Ring Road, Haidian District,Beijing 100083 PRChina
TEL:+86-10-82883159/3189 FAX:+86-10-82376577
E-mail: [email protected]
China: Thermaltake Beijing Co.Ltd
Overseas Branch
Address: 525Parritott Place,
City of Industry, CA 91746
TEL: (626)968-9189 FAX: (626)968-7659
E-mail: [email protected]
USA: Thermaltake Technology Inc.
Address: 8F, No.27, Lane 155, Sec.3, Pei Shen Road, Saen
Keng Hsiang, Taipei Hsiang, Taiwan
TEL:(886) 2-2662-6501 FAX:(886) 2-2662-6510
Taiwan : Thermaltake Technology Co.,Ltd.
Address: No.5-A, Hei-An Bldg 2-6-16 Okubo,
Shinjuku-ku, Tokyo, 169-0072, Japan
TEL: +81- 3-3203-3371 FAX: +81- 3-3203-3372
E-mail: [email protected]
Japan: Thermaltake Japan Inc.
O1693
Note Dual heatpipe VGA cooler
Fanless VGAFanless VGA
>
>>>> 22
Thank you for purchasing Fanless VGA. This product is a
new GPU thermal solution that applies heatpipe
technology and can be applied to video card with
mounting holes on the PCB.
Be sure to read this user guide in order to use this
product properly and safely.
Features :
>>
>> - High performance fanless GPU cooler,
0dBA cooling solution, reduce total
system noise
- Dual heatpipe move the heat more
efficiently
- Much better heat dissipation is
delivered by larger heatsink surface
- Universal clip for both nVIDIA and Ati
Note
Contents
>> 21
>>
>>
Heat Sink Base Installation
Clip Installation
Heatpipe Installation
1
3
7
13
Component
NOTICE: Thermaltake is not responsible for
any damaged caused by the incorrect
installation or usage of this product.
Fanless VGAFanless VGA
Installation Installation
>> 03>> 18
Heat sink base
Installation
Main rear heat sink plate
Step12: Position the main rear heat sink.
After applying equal amount of thermal grease on the
tunnel of the main rear heat sink, position the main rear
heat sink plate toward the heatpipe and then mount it onto
the rear heat sink base using screw-E.
Important : Make sure the finished
Fanless VGA is similar to the picture
as shown. Main rear heat sink needs
to be in position underneath with the
main front heat sink.
Screw - E
Fanless VGAFanless VGA
>>
>>
Installation Installation
>> 17>> 04
Make sure the surface of the GPU core are clean before
applying thermal grease onto it.
Step1: Apply the thermal grease on the GPU.
Front Back
Fanless VGAFanless VGA
Thermal
Grease
>>
>>
>> Important : Make sure the
position of the heatpipe is
according to the drawing.
Step11: Apply the thermal grease on the
rear heat sink base.
Turn the card over and apply equal amount of thermal
grease on the rear heat sink base (Thermal grease
should also be applied into the tunnel ). Then, position
the heatpipe into the tunnel on rear heat sink base.
Front
Back
Installation Installation
>> 05>> 16
>>
Step10: Mount the main front heat sink.
Mount the main front heat sink onto it using screw-E.
Front View
Attention on the
position of the
inserted heatpipe
Side View
Screw - E
Important :
Most GPU`s on the video card are slightly concave, the
curvature of which is directed toward the center. Thus,
more thermal grease is required at the center. Also, in the
case of the ATI Radeon 9700 Pro and 9800 Pro, the
protruding graphics core is surrounded by a protective
frame, which is higher than the core itself, thus generous
amounts of thermal grease must be applied on the core.
If proper contact between the front heatsink and the GPU
core cannot be made, it will lead to the possibility of the
core being overheat.
ATI Radeon 9700 Pro
ATI Radeon 9800 Pro
Fanless VGAFanless VGA
>>
Installation Installation
>> 15>> 06
Step2: Place the front heat sink base.
Place the front heat sink base on top of the GPU.
Front heat sink base
Front
Heatpipe
Position the heatpipe into the tunnel on front heat sink
base.
Step9: Install the heatpipe.
The pointed part of the heatpipe
should be facing downward.
Important :
Please pay attention to the
position of the inserted heatpipe.
>>
Fanless VGAFanless VGA
>> >>
Other Thermaltake Computer Hardware manuals
Thermaltake
Thermaltake Pacific PR32-D5 Plus User manual
Thermaltake
Thermaltake Pacific V-RTX 2070 Super Plus User manual
Thermaltake
Thermaltake Pacific V-RTX 3070 Plus User manual
Thermaltake
Thermaltake CLP0538 User manual
Thermaltake
Thermaltake Pacific RL360 D5 User manual
Thermaltake
Thermaltake Bigwater 780e CL-W0169 User manual
Thermaltake
Thermaltake Pacific V-RTX 4090 Plus User manual
Thermaltake
Thermaltake TOUGHLIQUID Ultra 360 User manual
Thermaltake
Thermaltake CPU Cooler Socket 478 User manual
Thermaltake
Thermaltake Pacific A2 Ultra User manual
Thermaltake
Thermaltake Pacific MX2 Plus User manual
Thermaltake
Thermaltake Pacific V-RTX 4090 Plus User manual
Thermaltake
Thermaltake Pacific MX1 Plus User manual
Thermaltake
Thermaltake V3 Black Edition VL8000 Series User manual
Thermaltake
Thermaltake Water 3.0 Ultimate User manual
Thermaltake
Thermaltake TH240 ARGB Sync User manual
Thermaltake
Thermaltake TH240 ARGB Sync User manual
Thermaltake
Thermaltake Pacific R240 D5 User manual
Thermaltake
Thermaltake Pacific MX2 Ultra User manual
Thermaltake
Thermaltake Floe Ultra 240 RGB User manual
Popular Computer Hardware manuals by other brands
EMC2
EMC2 VNX Series Hardware Information Guide
Panasonic
Panasonic DV0PM20105 Operation manual
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 user manual
Gigabyte
Gigabyte B660M DS3H AX DDR4 user manual
Raidon
Raidon iT2300 Quick installation guide
National Instruments
National Instruments PXI-8186 user manual
