Do not operate the machine in explosive
atmospheres, such as in the presence of ammable
liquids, gases or dust. The machine creates sparks
which may ignite flammable materials.
Do not operate the machine on a gravel or uneven
surface where ejected material may result in injury.
Keep the work area clean and well lit. Cluttered or
dark work areas invite accidents.
Do not expose the machine to rain or wet conditions.
Water entering the machine may increase the risk of
electric shock.
Starting up the machine
Before connecting the plug to the machine:
Check all the screws, nuts and other fasteners
are properly secured.
Check guards, deectors and screens are in
place and good working condition.
Make sure the lling hopper is empty.
Make sure the inlet and discharge opening
guards are properly in place.
Check all the parts of the machine carefully to
determine if it operates properly and performs
its intended function. Especially, never use the
machine if the switch does not work normally.
If the supply cord is damaged, ask one of our
authorised service dealers, always using genuine
replacement parts, to replace it.
Electrical safety
WARNING:
This is a Class I appliance. Connect with a supply
socket with an earth terminal. Improper earth may
cause electric shock and death. Use only three-wire
extension cords which have three-prong grounding-
type plugs and three-pole receptacles which accept the
tool’s plug.
Avoid contact with earthed or grounded surfaces
(e.g. pipes or radiators) during operation.
Use only IEC60245 (H07RN-F) extension cable for
outdoor use with splash-proofed connector. Its cross-
section must be at least 1.5 mm2for cable lengths up to
25 m, and 2.5 mm2for cable lengths over 25 m.
Voltage drop may occur when using a long thin cable,
this will reduce the power of the machine.
When using the extension cable, make sure that it does
not interfere with the operation of the machine and is
not squeezed or bent, and the plug does not get wet.
When using a cable reel, wind the cable completely off
the reel.
Do not misuse the cord. Never use it for carrying,
pulling or unplugging the machine. Keep it away
from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
Check the extension cable regularly for damage to the
insulation. Replace it if damaged.
If the connecting cable is damaged, withdraw the mains
plug immediately. A damaged cable may cause contact
with live parts and electric shock.
Never use damaged cables.
Only plug the machine into sockets in tested electrical
circuits. Check that the system voltage matches that on
the rating plate.
•
•
•
•
•
–
–
–Make sure you are wearing appropriate clothes.
–
–
–
•
•
•
•
•
•
•
•
•
•
•
•
Never deactivate or bypass the protective devices.
When using the machine outdoors, always use a
residual current-operated circuit-breaker (RCD) with an
operating current of 30 mA or less.
Operation
Keep your face and body away from the inlet opening.
Never put your hands or other partsyour body or
clothing inside the inlet and discharge opening, or near
moving parts. This may result in serious injury.
Do not overreach. Keep proper footing and balance at
all times. This enables better control of the machine in
unexpected situations. Don't stand at a higher level than
the base of the machine when feeding material into it.
Always keep clear of the discharge opening during
operation.
Observe regional regulations for noise protection.
Do not shred rocks, metal, bottles or other foreign
matter. Make sure that these foreign objects are not
in the branches that you shred.
Immediately switch off the motor and unplug it if the
blade strikesa foreign object or the machine starts
vibrating or making noise unusually. Check the
shredder for damage, and tighten any loose parts. Ask
an authorised service dealer to repair the machine.
Do not let the processed material accumulate in
the discharge opening. Otherwise it may result in
material being thrown through the inlet opening.
Switch off the motor and unplug it:
Whenever leaving the machine unattended
Before clearing a blockage or any fault
Before checking, cleaning or working on the
machine
Before making any adjustments, changing
accessories or storing
Whenever the machine starts vibrating or making
noise unusually
Clearing the inlet or discharge opening
Attaching or removing the collection box
Transporting.
Do not tilt the machine during operation.
Keep well clear when you shred long material. It may
spring back and this may result in personal injury.
Do not operate without the lling hopper.
Do not force the machine. It will do the job better
and safer at the rate for which it was designed.
Frequent overload may cause motor damage or re.
Use the right appliance. Do not use appliances for
purposes that it is not intended for. Never shred
metal, glass, stone, ceramics, plastics, thicker
branches, hard wood or thick wood plates, etc.
Maintenance instructions
Have your machine serviced by our authorised service
dealer, only use genuine replacement parts. Incorrect
repair and poor maintenance can shorten the life of the
machine and increase the risk of accidents.
Before servicing, inspection, adjustment, storage, or to
change an accessory, take following steps:
Shut off the power
Disconnect the machine from the power supply
Make sure that all moving parts have come to a
complete stop
Allow the machine to cool.
•
•
•
•
•
•
•
•
•
•
•
–
–
–
–
–
–
–
–
•
•
•
•
•
•
•
–
–
–
–
