The Handy THIS User manual

Page 1

OPERATOR’S MANUAL AND PARTS LIST

2400W IMPACT SHREDDER - THIS

Sales & Helpline 01793 333220

www.thehandy.co.uk

Before use please read & understand this manual, paying particular

attention to the safety instructions.

2010 v1

Page 2

CONTENTS

SAFETY INSTRUCTIONS 3

MAJOR PARTS 4

ASSEMBLY 5

OPERATION 6

PARTS DIAGRAM AND LIST 7-8

EC DECLARATION OF CONFORMITY 9

Page 3

SAFETY INSTRUCTIONS

Read and understand the owner’s manual and labels afxed to the

electric shredder. Learn its application and limitations as well as the

specic potential hazards. Retain these instructions for reference.

• TheImpactShredderisanelectricalapplianceusingfastmovingparts

 andassuchcanbedangerousifhandledirresponsibly.

• Ensurethatnoforeignobjectssuchasstones,glass,metal,earthor

 plasticsarefedintotheshredder;thesecouldcausebluntingofthe

 bladeandseriouslydamagethemotor.

• Onlyuseextensioncablesthatareapprovedforoutdooruse.Check

 thattheyareingoodcondition.

• Useglovesandearprotectionifoperatingforextendedperiodsoftime.

• Werecommendsafetygogglesarewornduringoperationasobjects

 canbeejectedathighspeedwhenthemotorisrunning.

•  Allonlookers,childrenandpetsshouldbekeptatasafedistanceand

 onlythosefamiliarwiththeoperationoftheshreddershouldbe

 permittedtouseit.

• Neverexposetheunittorainormoistureandstorethemachineina

 totallydryenvironment.

• Alwaysturnofftheunitandfullydisconnectfromthemainselectricity

 supplywhencleaningorperforminganymaintenance.Waituntilthe

 cuttingdiscstops.

• Neverinserthandsintothefeedhopperordebrischutewhilsttheunit

 isrunningorconnectedtothemainselectricitysupply.

• Donotmodifytheunitinanyway.

• Replacewornordamagedpartsusingonlyoriginalspares.

• Nevermovetheshredderbypullingonthecableandalwaysswitchoff

 whentransporting.Donotleavetheshredderunattendedwhilstitis

 switchedon.

Page 4

MAJOR PARTS

Handle

Hopper

ShredderBody MotorCover

DischargeChute

Axle

PowerCord

CoverSecuringKnob

MainSwitch

OverloadResetButton

Supports

Page 5

ASSEMBLY

• InserttheAxlethroughthepre-drilledholesintheFootSupports.

• Insertthesupportsintothebodyoftheshredderasshown.

• AttacheachWheeltotheAxleintheordershownbelowand

ensurethatthenutisnottootight.(Fromlefttoright-washer,

axlesleeve,wheel,washer,nut,wheelcover).Somemodelsmay

nothavetheaxlesleeve.

• OnthebodyofthemachinetightentheCoverSecuringKnob.This

knobhasasafetyswitchbuiltintoitandthemachinewillnotacti-

vateunlesstheknobistightened.

• Attachthecollectionbagtothemachinebymeansofthehookson

thesidesofthedischargechute.

• Donotusetheshredderwithoutthehopper.

SPECIFICATION

Model No THIS

Voltage 230-240V~50Hz

Power S1:2000W,S6:2400W

No-loadSpeed 4500rpm

MaxBranchDiameter 40mm

SoundPowerLevel 107dB(A)

LengthofCable 0.35m

ProtectionClass IPX4

NetWeight 14kg

Page 6

OPERATION

• Placethemachineonrm,levelgroundwhilstoperatingandplacereceptacleunder-

neaththedischargechuteorattachthecollectionbag.

• Presstheswitchmarked“I”tostartand“0”tostopthemotor.Presstheoverloadreset

buttonifthemachinedoesnotwork,ensuringyouhaveconnectedtothepowersupply.

• Allowthemotortorunforafewsecondsbeforecommencingwork.

• Inspectthematerialtobeshreddedbeforestartingandremoveanysharpobjects,

stones,wireetcwhichcoulddamagethecuttingmechanism.

• Themachinewillautomaticallypullthewastematerialin.Donotforcetoomuchmate-

rialinatonceotherwisethechutemayblockup.

• Ifablockageoccursandthebladestopworking,disconnectthemachineandfreeany

jammedmaterial.Ifthebladestallsformorethan5seconds,theoverloadswitchwillcut

inandswitchoffthemachine.Allowthemachinetocoolforatleast1minutebeforeat-

temptingtore-start.Pushtheoverloadswitchrst,thentheOn/Offswitch.

• Thereisaplungerprovidedtoaidthethefeedingofsoftermaterial-donotfeedsoft

kitchenwasteintotheshredder-itisbettertocompostit.

Hints and Tips:

• Usethemachinetoshredthefollowingmaterialsonly-twigsandbranches(maxdia

40mm),pruningtrimmings,hedgetrimmings,plantmaterialandroots(removesoilrst).

• Bealerttolongleafbrancheswhichcanwhipbackastheyarebeingdrawnintothe

shredder.

• Organicmaterialwhichcontainsalargeamountofwaterandsapcansticktothecutting

blades-itisbesttoleaveitforafewdaystodryout.

• Tomakenercomposttheshreddedmaterialcanbepassedthroughasecondtime.

• Keeptheventilationslotsonthebodyfreeofdustanddebris.

• Donotleavetheshredderrunningunattended;disconnecttheplugwhenleavingor

movingthemachine.

Blade Replacement:

• Thebladeshavetwocuttingedges.Whenthebladesbecomeworntheycanbere-

versedtousethesecondcuttingedgebuttheseshouldbechangedbyanauthorised

servicedealer.

• Whenbothedgesofthebladeshavebecomeworntheymustbereplacedas a pair.

Thebladescanbere-sharpenedbutthismustbedonebyaprofessionalusinganoil

stone.Theweightofeachbladeiscriticaltomaintainthebalanceofthecuttingdisc.

Maintenance:

• Duringanymaintenanceworkensurethatthemachineisswitchedoffanddisconnected

fromthemains.

• Ifanextensioncableisuseditmustbeofthesamegradeasthatttedtotheshredder.

Checkthecablesregularlyforsignsofdamageorwear.

• Neverattempttooverridetheoverloadswitch-itisthereforyoursafety.

• Removealldepositedmatterafterusewithabrushandcleanthemachineandallplas-

ticpartswithsoapandadampcloth.

• Donotcleantheshredderwithahosepipeorbyrinsing.Nowatershouldbeallowedto

entertheshredder.

Page 7

PARTS DIAGRAM

Page 8

PARTS LIST

No Part No Desc No Part No Desc

1 TH101-911365002 WarningSticker 2 TH101-9151650001 Hopper

3 TH101-9053650006 RubberFlap 4 TH101-9150650001 ClampBar

5TH101-9SBABC4.2-20 Screw 6 TH101-9114-650001 Logo

7 TH101-9001650001 UpHousing 8 TH101-6053650005 BoltFramePlate

9 TH101-9SBABC04-10 Screw 10 TH101-9WSB-4 SpringWasher2

11 TH101-9030650001 SwitchPin 12 TH101-9057-650001 Plunger

13 TH101-9SBABC05-20 “H”TypeScrew 14 TH101-9SBABC08-30 Screw

15 TH101-9WSB-08 SpringWasher1 16 TH101-907265000 ClampBlock

17 TH101-9132650001 Screw 18 TH101-9132650001 BladeSetInc

Screws

19 TH101-9072650001 BladePlate 20 TH101-9072650002 DriveBlock

21 TH101-9053650008 BladeDefendBlock 22 TH101-9057650003 PullBar

23 TH101-9030650004 Washer3 24 TH101-9NCN04 Nut

25 TH101-9SBABC4.2-18 Screw 26 TH101-9002650001 DownHousing

27 TH101-9058650001 Knob 28 TH101-9060650001 Spring

29 TH101-9030650002 InternalNut 30 TH101-9075650001 Nut

31 TH101-9053650007 NutFramePlate 32 TH101-9NAN-04 HexNut

33 TH101-9032650001 OverloadSwitch 34 TH101-9029650001 PowerCord

35 TH101-9023630001 CordSheath 36 TH101-9053650001 CordClampPlate

37 TH101-9053650004 SwitchFramePlate 38 TH101-9SBABC05-20 Screw

39 TH101-9SBABC04-40 Screw 40 TH101-9131650001 Filter

41 TH101-9027650001 ConnectingWire1 42 TH101-9027650002 ConnectingWire2

43 TH101-9032650002 Electromagnetic

Switch

44 TH101-9092650001 Overcurrent

protection

45 TH101-9113650001 DataSticker 46 TH101-9142650001 MotorCover

47 TH101-9033620001 Capacitor 48 TH101-9022650001 Fan

49 TH101-9023650002 ShaftSheath 50 TH101-9DB-6080Z Bearing

51 TH101-9SBABC04-75 Screw 52 TH101-9039650001 MotorSupport

53 TH101-9005650001 Field 54 TH101-9013650001 Armature

55 TH101-9DB-62010Z Bearing 56 TH101-9030650005 Washer

57 TH101-9031650004 SmallBeltWheel 58 TH101-9053650002 WindDefendBoard

59 TH101-9138650001 PlasticPin 60 TH101-9069650003 DownCoverGear-

box

61 TH101-9DB6290Z Bearing 62 TH101-9031650003 EccentricWheel

63 TH101-9031650002 BigBeltWheel 64 TH101-9047650001 Belt

65 TH101-9069650002 UpCoverGearbox 66 TH101-9DB-60030Z Bearing

67 TH101-9098650001 Spanner 68 TH101-9069650001 WheelCover

69 TH101-9NCN-08 HexNut 70 TH101-9030650003 Washer

71 TH101-9038650001 SupportTube 72 TH101-9057650002 ConnectingPole

73 TH101-9030650003 Washer 74 TH101-9023650001 WheelAxleSleeve

75 TH101-9031650001 Wheel 76 TH101-101-BAG CollectionBag

Page 9

DeclarationofConformity

PursuanttotheregulationsofthefollowingECDirectives:

-ElectromagneticCompatabilityDirective89/336/EEC

-LowVoltageDirective73/23/EEC

-MachineryDirective98/37/EC

-NoiseEmissionDirective2000/14/EC

HandyDistributionLtdherebydeclaresthattheproduct:

MachineType:Impact Shredder

MachineModel:THIS

ConformstothemainsafetyrequirementsoftheECDirectiveslistedabove.

Thisconformityisbasedonthefollowingstandardsandnormativedocuments:

EN 55014-1:2000+A1+A2

EN 55014-2:1997+A1

EN 61000-3-2:2000

EN61000-3-11:2000

EN 60335-1:2002+A1+A11

EN 13683:2003

98/37/EC-AnnexI

Theresponsibleperson,basedwithintheEC,isidentiedbelow

Name:MrDerekBelcher

Title:ManagingDirector

Company:HandyDistributionLtd

Address:HobleyDrive,StrattonStMargaret,SWINDON,SN34NS

Signature:      Date:20thFeb2008   

EC DECLARATION OF CONFORMITY

Page 10

Toordersparepartsandseethecompleterangeofgarden

machineryandgardenequipmentfromHandy,visit:

www.thehandy.co.uk

Other manuals for THIS

Table of contents

Other The Handy Paper Shredder manuals

The Handy

The Handy THSSWB User manual

The Handy

The Handy THPDS65 User manual

The Handy

The Handy THSSWB User manual

The Handy

The Handy THHSWB Installation and maintenance instructions

The Handy

The Handy THIS User manual

The Handy

The Handy THISWB User manual

The Handy

The Handy THIS Installation and maintenance instructions

The Handy

The Handy THSS User manual

Popular Paper Shredder manuals by other brands

Swingline

Swingline STACK-AND-SHRED200X&200XL 60X Start here

GBC

GBC ShredMaster CC055 instruction manual

UNITED OFFICE

UNITED OFFICE UAV 190 A1 operating instructions

UNITED OFFICE

UNITED OFFICE UAV 190 A1 operating instructions

Rexel

Rexel Optimum AutoFeed+ 45X instruction manual

Martin Yale

Martin Yale 227284S1 instruction manual

Bonsaii

Bonsaii DocShred C223-A instruction manual

HSM

HSM Pure 740 max operating manual

TRU RED

TRU RED TR-BMC20A Operator's manual

Fellowes

Fellowes 50S instructions

GBC

GBC SHREDMASTER 1236SE operating instructions

Gude

Gude GH 2600 P operating instructions

Ativa

Ativa DQ80M operating instructions

Q-Connect

Q-Connect Q8CC instruction manual

Fellowes

Fellowes POWERSHRED C-325CI instructions

Olivetti

Olivetti Privacy 5000C Operational manual

UNITED OFFICE

UNITED OFFICE UAV 190 A1 operating instructions

Dahle

Dahle paperSAFE 22022 instructions