Texas Instruments MSP432P401R User manual

MSP432P401R Launchpad External Target Mod

This guide walks through the steps of connecting to and programming an external target using

the MSP432P401R LaunchPad Development Kit.

Figure 1: MSP432P401R LaunchPad Development Kit

Step 1:

Remove the board from the packaging.

Figure 2: MSP432P401R LaunchPad out of box (with wires attached)

Step 2:

Remove the jumpers from the isolation header as well as switch S101 to the “XDS-ET”position (not the

“Ext Debug”position).

Figure 3: Headers Removed and Switch Positioned

Step 3:

Attach wires to each of the positions in J103 on the side of the board near the reset button.

Figure 4: Jumper wires soldered into J103 on the LaunchPad

Step 4:

Attach a wire for the “TDI”signal by soldering a wire into pin 6 of the debug select switch (S101) as

shown in the figure below. Ensure that the switch remains in the “XDS-ET”position.

Figure 5: Wire Soldered to "TDI" Signal on S101

Step 5:

Attach a wire for the “SWO”signal by soldering a wire to pin 12 of IC111. Since the traces are small on

that component, it is easiest to attach the wire directly to the trace.

Figure 6: Wire Soldered to "SWO" Signal from Pin 12 on IC111

Carefully scratch off the soldermask from the trace leading to pin 12 on IC111. This will allow for more

space to solder a wire.

Figure 7: Close-up of IC111 and the Soldering Location for the "SWO" Signal

Solder a wire to the exposed copper of the trace and be careful to not strain the wire as it may damage

the board.

Figure 8: Wire Soldered to the "SWO" Signal

Step 6:

Attach the wires from J103 on the LaunchPad to their corresponding positions on whatever target board

you want to program. Not all signals are required from J103.

Step 7:

Attach the “TDI”and “SWO”wires to their corresponding positions on the target board.

Step 8:

Connect the MSP432P401R LaunchPad to the computer via the micro USB cable and check to see if

“LED102”is illuminated green near the reset button. If the LED is not on, try cycling the power on the

target board by quickly removing and replacing the +3.3V wire. Repeat with pauses in between until

LED02 illuminates.

Figure 9: Launch Pad Connected to Target with LED02 Illuminated

Step 9:

Program the external target board using your preferred method. Note that I have only tried this with

Code Composer Studio and Energia and it works fine but I’m assuming it should work with other IDEs.

No guarantees though.

Other manuals for MSP432P401R

Table of contents

Other Texas Instruments Microcontroller manuals

Texas Instruments

Texas Instruments MSP430F6735 User manual

Texas Instruments

Texas Instruments CC2520 User manual

Texas Instruments

Texas Instruments ADC12DJ3200CVAL User manual

Texas Instruments

Texas Instruments MSP430FG6625 User manual

Texas Instruments

Texas Instruments SimpleLink MSP432P4 Series Product manual

Texas Instruments

Texas Instruments CC1125 User manual

Texas Instruments

Texas Instruments TPS929120EVM User manual

Texas Instruments

Texas Instruments CC110 Series Guide

Texas Instruments

Texas Instruments MSP-EXP430G2ET User manual

Texas Instruments

Texas Instruments TMS320C6000 DSP Guide

Texas Instruments

Texas Instruments CC3235MODSF SimpleLink User manual

Texas Instruments

Texas Instruments CC2520EM User manual

Texas Instruments

Texas Instruments TMS370 Series Use and care manual

Texas Instruments

Texas Instruments TPS65941212-Q1 User manual

Texas Instruments

Texas Instruments Chipcon Products CC1110DK User manual

Texas Instruments

Texas Instruments TMS570LS User manual

Texas Instruments

Texas Instruments SimpleLink CC3200 Wi-Fi Product manual

Texas Instruments

Texas Instruments TIDA-00204 User manual

Texas Instruments

Texas Instruments LaunchPad MSP430FR2355 User manual

Texas Instruments

Texas Instruments TMS320F28004 Series User manual

Texas Instruments

Texas Instruments MSP430F67451 User manual

Texas Instruments

Texas Instruments MSP430G2533 User manual

Texas Instruments

Texas Instruments CC1110 Programming manual

Texas Instruments

Texas Instruments MSP430FG47x User manual

Popular Microcontroller manuals by other brands

AMS

AMS AS7261 Demo Kit user guide

Novatek

Novatek NT6861 manual

Espressif Systems

Espressif Systems ESP8266 SDK AT Instruction Set

Nuvoton

Nuvoton ISD61S00 ChipCorder Design guide

STMicrolectronics

STMicrolectronics ST7 Assembler Linker user manual

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM user guide

NEC

NEC 78GK0S/K 1+ Series Application note

Mikroe

Mikroe SEMITECH N-PLC Click Application note

Intel

Intel Agilex user guide

Cypress

Cypress CY4607 HX2VL quick start guide

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE manual

CYPRES

CYPRES CY14NVSRAMKIT-001 user guide

Espressif Systems

Espressif Systems ESP8266EX Programming guide

Abov

Abov AC33M8128L user manual

Laird

Laird BL654PA user guide

Silicon Laboratories

Silicon Laboratories C8051F800 user guide

Energy micro

Energy micro EFM32 Giant Gecko Starter Kit user manual

Mikroe

Mikroe click Proximity 2 manual