Texas Instruments MSP432 User manual

MSP432™ Hardware Tools

User's Guide

Literature Number: SLAU571A

March 2015–Revised May 2016

2SLAU571A–March 2015–Revised May 2016

Submit Documentation Feedback

Contents

Preface ........................................................................................................................................ 4

1 Hardware ............................................................................................................................ 5

1.1 MSP-FET-432ADPTR....................................................................................................... 6

1.1.1 Introduction .......................................................................................................... 6

1.1.2 Key Features ........................................................................................................ 6

1.1.3 Kit Contents.......................................................................................................... 6

1.1.4 Configuration and Usage .......................................................................................... 6

1.1.5 Hardware Design ................................................................................................... 7

1.2 MSP-TS432PZ100........................................................................................................... 8

1.2.1 Introduction .......................................................................................................... 8

1.2.2 Key Features ........................................................................................................ 8

1.2.3 Kit Contents.......................................................................................................... 8

1.2.4 Configuration and Usage .......................................................................................... 8

1.2.5 Hardware Design.................................................................................................. 11

Revision History.......................................................................................................................... 15

www.ti.com

SLAU571A–March 2015–Revised May 2016

List of Figures

1-1. MSP-FET-432ADPTR Schematic ......................................................................................... 7

1-2. Board Configuration For External Target Power Supply................................................................ 9

1-3. Board Configuration For Debugger-Supplied Target Power.......................................................... 10

1-4. MSP-TS432PZ100 Target Socket Board, Schematic ................................................................. 11

1-5. MSP-TS432PZ100 Target Socket Board, PCB ........................................................................ 12

List of Tables

1-1. Matrix of S1 Switch Orientation Compared to ARM Connector Option............................................... 6

1-2. MSP-FET-432ADPTR Bill of Materials.................................................................................... 7

1-3. Device Compatibility......................................................................................................... 8

1-4. Important Board Components ............................................................................................ 12

1-5. MSP-TS432PZ100 Bill Of Materials ..................................................................................... 13

4SLAU571A–March 2015–Revised May 2016

Submit Documentation Feedback

Read This First

MSP432, Code Composer Studio, TI E2E are trademarks of Texas Instruments.

ARM, Cortex are registered trademarks of ARM Limited.

IAR Embedded Workbench is a registered trademark of IAR Systems AB.

Preface

SLAU571A–March 2015–Revised May 2016

Read This First

About This Manual

This manual describes the hardware tools that support the Texas Instruments MSP432™ device family of

ARM®Cortex®-M based microcontrollers.

How to Use This Manual

This manual describes the setup and operation of the hardware tools. It does not fully describe the

MSP432 microcontrollers or the development software systems. For details of these items, see the

appropriate TI documents listed in Important MSP432 Documents on the Web.

Important MSP432 Documents on the Web

The primary sources of MSP432 information are the device-specific data sheets and user's guides. The

MSP432 web site contains the most recent versions of these documents.

Documents that describe the Code Composer Studio™ tools (Code Composer Studio™ IDE, assembler,

C compiler, linker, and librarian). A Wiki page (FAQ) that is specific to the Code Composer Studio tools is

available at processors.wiki.ti.com/index.php/Category:CCS. The TI E2E™ Community support forums

provide additional help.

Documentation for third-party tools, such as the IAR Embedded Workbench®for ARM IDE or the Segger

J-Link debug probe, can be found on the respective third-party website.

If You Need Assistance

Support for the MSP432 devices and the hardware development tools is provided by the Texas

Instruments Product Information Center (PIC). Contact information for the PIC can be found on the TI web

site. The TI E2E™ Community support forums for the MSP432 provide open interaction with peer

engineers, TI engineers, and other experts. Additional device-specific information can be found on the

MSP432 web site.

SLAU571A–March 2015–Revised May 2016

Hardware

Chapter 1

SLAU571A–March 2015–Revised May 2016

Hardware

This chapter contains information relating to the hardware tools and includes schematics, PCB pictorials,

and bills of materials. All other tools are described in separate product specific user's guides. Information

about the TI XDS100 and XDS200 debug probes is not included in this document, and can be found at

www.ti.com/tool/xds100 and www.ti.com/tool/xds200, respectively.

Topic ........................................................................................................................... Page

1.1 MSP-FET-432ADPTR ............................................................................................ 6

1.2 MSP-TS432PZ100................................................................................................. 8

MSP-FET-432ADPTR

www.ti.com

6SLAU571A–March 2015–Revised May 2016

Submit Documentation Feedback

Hardware

1.1 MSP-FET-432ADPTR

1.1.1 Introduction

The MSP-FET-432ADPTR is an adapter to convert the 14-pin JTAG connector to either standard ARM 10-

pin or ARM 20-pin connectors. This allows for use of the MSP-FET debug probe with MSP432 Cortex-M

devices.

1.1.2 Key Features

• Use MSP-FET to debug MSP432 Cortex-M Devices

• 10-pin ARM support

• 20-pin ARM support

1.1.3 Kit Contents

• 1x MSP-FET-432ADPTR 14-pin JTAG to ARM adapter

1.1.4 Configuration and Usage

The MSP-FET-432ADPTR allows the use of the MSP-FET debug probe with the MSP432 Cortex-M family

of devices. Operation is straight-forward, with only one selection for how the power is sourced. This

selection is required because of the difference in the power source and sense behavior of the MSP-FET

and the ARM debug standard.

The MSP-FET debug probe has two power states:

1. VCC Output

• MSP-FET outputs a voltage to the target.

• Output voltage is configurable in the IDE.

• In VCC output state, the MSP-FET voltage sense functionality is not enabled.

2. VCC Sense

• MSP-FET senses an existing external voltage (not from the MSP-FET itself).

• The JTAG signals are level shifted accordingly to match this voltage.

• In VCC Sense state, the MSP-FET output voltage is not provided.

The Cortex-M debug standard works a bit differently. In this standard, the VCC Sense is always active, no

matter where the external voltage is coming from. Some debug probes, such as the IAR I-jet and Segger

J-Link have a voltage output, all while still sensing the VCC Sense.

Table 1-1. Matrix of S1 Switch Orientation Compared to ARM Connector Option

VCC Sense (S1 Left) VCC Output (S1 Right)

ARM 20-pin connector • External power is sensed through ARM pin 1

• External power needs to be connected to

debug target

• Power is provided by the MSP-FET through

ARM pin 19.

• Alternatively, power can be wired to the target

using connector J4.

• This output matches other ARM debug probes

like IAR i-Jet and SEGGER J-Link

• Note that the IAR i-Jet outputs 3.3 V, and

SEGGER J-Link outputs 5 V on this pin.

Ensure the target accounts for the specific

voltage output by MSP-FET.

ARM 10-pin connector • External power is sensed through ARM pin 1

• External power needs to be connected to

debug target

• There is no pin to connect the power output

on the 10 pin connector

• Power output is provided on connector J4.

This can be wired to the target board.

1 2

3 4

5 6

7 8

9 10

1 2

3 4

5 6

7 8

9 10

11 12

13 14

15 16

17 18

19 20

2L1 1

L2 3

5L3 4

L4 6

1 2 3 4

www.ti.com

MSP-FET-432ADPTR

SLAU571A–March 2015–Revised May 2016

Hardware

1.1.5 Hardware Design

Figure 1-1 shows the schematic of the MSP-FET-432ADPTR.

Figure 1-1. MSP-FET-432ADPTR Schematic

Table 1-2 lists the bill of materials for the MSP-FET-432ADPTR.

Table 1-2. MSP-FET-432ADPTR Bill of Materials

Qty Reference Manufacturer Description Part Number Alternate

Part

Number

PCB Decal,

Package Supplier Digi-Key Number

1 J1 Standard Conn Header 14POS 0.100" TH,

RA, Gold, Digikey S9203-ND 2 x 7 0.100" Digikey S9203-ND

1 J2 Samtec CONN HEADER 10POS DUAL

VERT, Digikey FTSH-105-01-F-

D-K-ND

FTSH-105-01-

F-D-K 2 x 5 0.050" Digikey FTSH-105-01-F-D-K-ND

1 J3 Standard CONN HEADER LOW-PRO

20POS GOLD, Digikey

HRP20H-ND 2 x 10 0.100" Digikey HRP20H-ND

1 J4 Standard CONN HEADER .100 SINGL

STR 3POS, Digikey S1012E-03-

ND 1 x 3 0.100" Digikey S1012E-03-ND

1 S1 Standard SW SLIDE DPDT 2POS,

Digikey 401-2001-ND M096V Digikey 401-2001-ND

1 MH1 Standard Standoff Nylon 4-40 8mm/

0.375" CM

1 MH2 Standard Standoff Nylon 4-40 8mm/

0.375" CM

MSP-TS432PZ100

www.ti.com

8SLAU571A–March 2015–Revised May 2016

Submit Documentation Feedback

Hardware

1.2 MSP-TS432PZ100

1.2.1 Introduction

NOTE: This kit does not include MSP432 microcontroller samples. To sample the compatible

devices, visit the product page or select the related MCU after adding the tool to the TI Store

cart: MSP432P401R.

The MSP-TS432PZ100 is a stand-alone ZIF socket target board used to program and debug the MSP432

MCU in-system through the JTAG interface or the Serial Wire Debug (SWD 2-wire JTAG) protocol. Two

standard ARM Cortex-M debug connectors provide connectivity to a large number of debug probes from

Texas Instruments and third parties.

All device pins are readily accessible through dedicated headers, which makes the board the ideal center

of a prototype setup.

1.2.2 Key Features

• ZIF socket for 100-pin QFP (PZ) packages

• Access to all 100 device pins

• LEDs and buttons

• 2 x Cortex-M JTAG connectors supporting all 10- or 20-pin compatible debug probes

1.2.3 Kit Contents

• One READ ME FIRST document

• One MSP-TS432PZ100 target socket board

• One TI Terms and Conditions for Evaluation Modules

• One 32.768-kHz crystal from Micro Crystal

• Four SAM1029-25-ND 25-pin 100-mil through-hole male headers

• Four SAM1213-25-ND 25-pin 100-mil through-hole female headers

1.2.4 Configuration and Usage

Table 1-3 lists the devices that are compatible with the MSP-TS432PZ100 target socket board.

Table 1-3. Device Compatibility

Board Socket Type Supported Devices

MSP-TS432PZ100 100-pin QFP (PZ100) MSP432P401RIPZ

MSP432P401MIPZ

Feed external

GND here

Feed external

VCC here

www.ti.com

MSP-TS432PZ100

SLAU571A–March 2015–Revised May 2016

Hardware

1.2.4.1 Board Configuration For External Target Power Supply

If the application needs to operate in stand-alone mode (for example, to measure current consumption

without debug overhead) or when using ARM Cortex-M debug probes that do not provide power for the

target device (for example, TI XDS100, XDS200, Keil ULINK2, or Keil ULINK Pro), power must be

supplied externally to the target socket board.

Always follow the voltage limits defined in the device data sheet. Also make sure that the following

jumpers have been set as shown here before connecting the debug probe and power supply (see

Figure 1-2):

• JP8: Open

• JP12: Open

• J1: Close 2-3

• JP1: Closed

• JP2: Closed

• J16: Closed

• J2: Connect external VCC to pin 1, and external GND to pins 2 or 3

Figure 1-2. Board Configuration For External Target Power Supply

MSP-TS432PZ100

www.ti.com

10 SLAU571A–March 2015–Revised May 2016

Submit Documentation Feedback

Hardware

1.2.4.2 Board Configuration When Using ARM®Cortex®-M Debug Probes With Target Power Supply

Capability

Some third-party ARM Cortex-M debuggers (for example, Segger J-Link and IAR i-Jet) can optionally

supply a 5-V voltage to the target system through pin 19 of the debug connector. The LDO IC2 uses this

voltage to generate the 3.3-V target supply voltage. To use the LDO, make sure the following jumpers are

set as shown here before connecting the debug probe (see Figure 1-3):

• JP8: Closed

• JP12: Closed

• J1: Close 1-2

• JP1: Closed

• JP2: Closed

• JP16: Closed

If the debug probe supplies a logic level voltage through pin 19, the LDO can be entirely bypassed using

JP15. Always follow the voltage limits defined in the device data sheet.

Figure 1-3. Board Configuration For Debugger-Supplied Target Power

Table of contents

Other Texas Instruments Microcontroller manuals

Texas Instruments

Texas Instruments LaunchPad CC1354P10-6 User manual

Texas Instruments

Texas Instruments Concerto F28M35 Series Product manual

Texas Instruments

Texas Instruments AFE4403 User manual

Texas Instruments

Texas Instruments Hercules TMS570LS04 Series User manual

Texas Instruments

Texas Instruments CC2531 Installation manual

Texas Instruments

Texas Instruments TMS320F2837 D Series User manual

Texas Instruments

Texas Instruments MSP430F67681 User manual

Texas Instruments

Texas Instruments 430BOOST-SENSE1 User manual

Texas Instruments

Texas Instruments Concerto F28M36 Series Product manual

Texas Instruments

Texas Instruments TMS570LS User manual

Texas Instruments

Texas Instruments eZ430-Chronos User manual

Texas Instruments

Texas Instruments MSPM0G110 Series Owner's manual

Texas Instruments

Texas Instruments LaunchPad MSP-EXP430F5529LP User manual

Texas Instruments

Texas Instruments LaunchPad MSP430FR4133 User manual

Texas Instruments

Texas Instruments TIDA-00204 User manual

Texas Instruments

Texas Instruments LaunchPad MSP430FR5994 User manual

Texas Instruments

Texas Instruments MSP430F6723A User manual

Texas Instruments

Texas Instruments LP-EM-CC1354P10-1 Manual

Texas Instruments

Texas Instruments BP-DAC11001EVM User manual

Texas Instruments

Texas Instruments MSP430F6721 User manual

Texas Instruments

Texas Instruments MSP430G2744DA User manual

Texas Instruments

Texas Instruments LAUNCHXL-CC1310 Manual

Texas Instruments

Texas Instruments Stellaris LM3S9B96 User manual

Texas Instruments

Texas Instruments MSP430F6767 User manual

Popular Microcontroller manuals by other brands

AMS

AMS AS7261 Demo Kit user guide

Novatek

Novatek NT6861 manual

Espressif Systems

Espressif Systems ESP8266 SDK AT Instruction Set

Nuvoton

Nuvoton ISD61S00 ChipCorder Design guide

STMicrolectronics

STMicrolectronics ST7 Assembler Linker user manual

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM user guide

NEC

NEC 78GK0S/K 1+ Series Application note

Mikroe

Mikroe SEMITECH N-PLC Click Application note

Intel

Intel Agilex user guide

Cypress

Cypress CY4607 HX2VL quick start guide

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE manual

CYPRES

CYPRES CY14NVSRAMKIT-001 user guide

Espressif Systems

Espressif Systems ESP8266EX Programming guide

Abov

Abov AC33M8128L user manual

Laird

Laird BL654PA user guide

Silicon Laboratories

Silicon Laboratories C8051F800 user guide

Energy micro

Energy micro EFM32 Giant Gecko Starter Kit user manual

Mikroe

Mikroe click Proximity 2 manual