Texas Instruments BOOSTXL-CAPKEYPAD User manual

SLAU758–January 2018

BOOSTXL-CAPKEYPAD Capacitive Touch BoosterPack Plug

‑

in Module

User's Guide

SLAU758–January 2018

BOOSTXL-CAPKEYPAD Capacitive Touch

BoosterPack Plug

‑‑

in Module

This getting started guide provides a brief overview of the BOOSTXL-CAPKEYPAD capacitive touch

keypad plug-in module for the TI LaunchPad development ecosystem. It describes the common use cases

for the BoosterPack module, introduces the required tools and hardware that are needed to develop with

it, and provides the relevant links to the detailed BOOSTXL-CAPKEYPAD EVM user's guide chapter in the

CapTIvate™ Technology Guide.

Contents

1 Introduction .................................................................................................................. 2

1.1 Scope ................................................................................................................ 2

1.2 Using the BOOSTXL-CAPKEYPAD ............................................................................. 2

2 Required Tools and Hardware ............................................................................................ 3

2.1 CapTIvate Design Center Tool.................................................................................... 3

2.2 Integrated Development Environment (IDE) or Flashing Utility............................................... 3

2.3 CAPTIVATE-PGMR Hardware.................................................................................... 4

2.4 Host LaunchPad Development Kit Hardware .................................................................. 4

3 Getting Started .............................................................................................................. 4

4 Hardware ..................................................................................................................... 4

4.1 Functional Block Diagram ......................................................................................... 4

4.2 BoosterPack Pinout ................................................................................................ 5

List of Figures

1 BOOSTXL-CAPKEYPAD ................................................................................................... 2

2 BOOSTXL-CAPKEYPAD Block Diagram ................................................................................ 4

3 BOOSTXL-CAPKEYPAD Pinout........................................................................................... 5

Trademarks

CapTIvate, MSP430, Code Composer Studio are trademarks of Texas Instruments.

Apple, OS X are registered trademarks of Apple Inc.

IAR Embedded Workbench is a registered trademark of IAR Systems.

Linux is a registered trademark of Linus Torvalds.

Microsoft, Windows are registered trademarks of Microsoft Corporation.

Introduction

www.ti.com

2SLAU758–January 2018

Submit Documentation Feedback

BOOSTXL-CAPKEYPAD Capacitive Touch BoosterPack Plug

‑

in Module

1 Introduction

The BOOSTXL-CAPKEYPAD is an easy-to-use evaluation module for the MSP430FR2522 capacitive-

touch-sensing microcontroller. This BoosterPack module enables you to extend your design for a

LaunchPad development kit by adding a 12-key capacitive touch numeric keypad with LED back-lighting

and proximity wakeup. Don't have a LaunchPad development kit? The BOOSTXL-CAPKEYPAD can also

be used as a simple CapTIvate technology evaluation module when coupled with the CAPTIVATE-PGMR

for interfacing to a host PC running the CapTIvate Design Center. It is even possible to bypass the

onboard keypad and connect up to three external capacitive sensors to the BOOSTXL-CAPKEYPAD to

test out your own sensor design concepts.

Figure 1. BOOSTXL-CAPKEYPAD

1.1 Scope

This getting started guide provides a brief overview of how the BOOSTXL-CAPKEYPAD can be used. The

full detailed EVM user's guide is available within the CapTIvate Design Center integrated documentation.

The latest version of the user's guide is also available online within the CapTIvate Technology Guide.

1.2 Using the BOOSTXL-CAPKEYPAD

While the BOOSTXL-CAPKEYPAD can be operated in a stand-alone fashion by applying external power

directly, it is most commonly used with either a host Launchpad development kit or the CAPTIVATE-

PGMR module.

1.2.1 Using the BOOSTXL-CAPKEYPAD With a LaunchPad Development Kit

The BOOSTXL-CAPKEYPAD can be used with a host LaunchPad development kit (such as the MSP-

EXP430F5529LP) to add capacitive touch keypad functionality to a new or existing design based on a

LaunchPad development kit. This use case enables the creation of a larger system in which the

BOOSTXL-CAPKEYPAD plays an HMI role.

www.ti.com

Required Tools and Hardware

SLAU758–January 2018

BOOSTXL-CAPKEYPAD Capacitive Touch BoosterPack Plug

‑

in Module

In this configuration, the BOOSTXL-CAPKEYPAD can be used out of the box with the factory

programming. It is not necessary to have a CAPTIVATE-PGMR module to program the onboard

MSP430FR2522 microcontroller. The host LaunchPad development kit only needs to be configured to

communicate with the BOOSTXL-CAPKEYPAD over the I2C interface using the SDA, SCL, and IRQ

signals provided on the 40-pin BoosterPack headers. The BOOSTXL-CAPKEYPAD powers up as an I2C

slave using the factory-programmed example. The host LaunchPad development kit can out the current

status of the BoosterPack plug-in module, as well as configure the operation of the BoosterPack plug-in

module, using the simple I2C register interface. The I2C register interface is documented in the detailed

user's guide, along with I2C transaction examples.

While the BOOSTXL-CAPKEYPAD can be used with any LaunchPad development kit that supports I2C

communication in the standard pin locations, TI provides several example projects for the host LaunchPad

development kit to enable quick development of an application.

The following software example projects for the host LaunchPad development kit are provided:

1. MSP-EXP430FR6989 + Segmented LCD

2. MSP-EXP430F5529LP + BOOSTXL-K350QVG-S1 QVGA LCD

3. MSP-EXP430F5529 USB Keyboard Example

All of these examples are compatible with the out-of-box BOOSTXL-CAPKEYPAD software.

1.2.2 Using the BOOSTXL-CAPKEYPAD With the CAPTIVATE-PGMR and the CapTIvate Design Center

The BOOSTXL-CAPKEYPAD can be used with the CAPTIVATE-PGMR module and CapTIvate Design

Center to view the real-time sensor data, tune the touch sensor performance, and program the onboard

MSP430FR2522 MCU. This use case is for those looking to evaluate CapTIvate touch sensing

performance or begin development of their own capacitive touch design using MSP430™ CapTIvate

touch-sensing MCUs.

The following software example projects for the BOOSTXL-CAPKEYPAD target are provided:

1. BOOSTXL-CAPKEYPAD Out-of-Box Experience (comes preprogrammed on a new BOOSTXL-

CAPKEYPAD)

2. BOOSTXL-CAPKEYPAD-EMC Noise Immunity Software Example

3. BOOSTXL-CAPKEYPAD-Prototyping External Sensor Example

These example projects may be programmed onto the MSP430FR2522 MCU on the BOOSTXL-

CAPKEYPAD using the CAPTIVATE-PGMR module and either Code Composer Studio™ (CCS) or IAR

Embedded Workbench®for MSP430.

2 Required Tools and Hardware

The following tools and hardware are required to use the BOOSTXL-CAPKEYPAD.

2.1 CapTIvate Design Center Tool

The CapTIvate Design Center is the one-stop-shop development environment for CapTIvate touch-

sensing MCUs. In addition to serving as the CapTIvate development graphical user interface, the design

center also contains all of the CapTIvate software examples and relevant technical documentation.

To get the most out of your BOOSTXL-CAPKEYPAD, download and install the latest version of the

CapTIvate Design Center from the MSPCAPTDSNCTR tool folder. The CapTIvate Design Center supports

Microsoft®Windows®, Apple®OS X®, and Linux®host environments. The minimum required CapTIvate

Design Center version with BOOSTXL-CAPKEYPAD support is version 1.60.00.00.

2.2 Integrated Development Environment (IDE) or Flashing Utility

To program a software example to either a host LaunchPad development kit or the BOOSTXL-

CAPKEYPAD, an integrated development environment is required. CapTIvate software examples support

TI Code Composer Studio (CCS) and IAR Embedded Workbench for MSP430. The minimum CCS version

with support for the MSP430FR2522 MCU is version 7.4. The minimum IAR EW version is version 7.11.

3 Sensing Lines I2C

SBW

14 LED Drive Lines

5 RX

Sensing Lines

3 TX Sensing Lines

UART

to HID

UART

to COM

I2C

IRQ A IRQ B

IRQ

3.3-V LDO

EnergyTrace

V+

5 V

V+

CAPTIVATE-PGMR

20-Pin Debug Header BoosterPack 40-Pin

Expansion Header

UART Selection IRQ Selection

LP3943 I2C LED Driver

12 Button Backlight LEDs,

2 Status LEDs

12-Button Keypad Matrix

With Guard and Proximity

Channel

Prototyping Header

V+ Selection

MSP430FR2522 MCU

7.25KB FRAM, 2KB SRAM, 8 CapTIvate I/Os

Required Tools and Hardware

www.ti.com

4SLAU758–January 2018

Submit Documentation Feedback

BOOSTXL-CAPKEYPAD Capacitive Touch BoosterPack Plug

‑

in Module

2.3 CAPTIVATE-PGMR Hardware

The CAPTIVATE-PGMR is required for connecting the BOOSTXL-CAPKEYPAD to a host PC to enable

communication with the CapTIvate Design Center and programming of the onboard MCU. The

CAPTIVATE-PGMR is needed to load code examples other than the out-of-box experience example that

comes preprogammed on the BOOSTXL-CAPKEYPAD. If you already have a CapTIvate MCU

development kit (MSP-CAPT-FR2633), a CAPTIVATE-PGMR is included in that development kit and can

be used with the BOOSTXL-CAPKEYPAD. The CAPTIVATE-PGMR is not required to use the BOOSTXL-

CAPKEYPAD with a LaunchPad development kit to add keypad functionality, and the BOOSTXL-

CAPKEYPAD can be used out of the box with the out-of-box preprogrammed firmware.

2.4 Host LaunchPad Development Kit Hardware

To run the host examples for the LaunchPad development kit, the appropriate LaunchPad development kit

is required. See the specific host example for LaunchPad development kit to determine which kit is

needed.

3 Getting Started

To get started with the BOOSTXL-CAPKEYPAD, see the BOOSTXL-CAPKEYPAD Getting Started section

of the CapTIvate Technology Guide.

4 Hardware

The following sections describe the BOOSTXL-CAPKEYPAD hardware. For a detailed description of the

hardware, see the BOOSTXL-CAPKEYPAD hardware description in the CapTIvate Technology Guide.

4.1 Functional Block Diagram

Figure 2 shows the BOOSTXL-CAPKEYPAD functional block diagram.

Figure 2. BOOSTXL-CAPKEYPAD Block Diagram

www.ti.com

Hardware

SLAU758–January 2018

BOOSTXL-CAPKEYPAD Capacitive Touch BoosterPack Plug

‑

in Module

4.2 BoosterPack Pinout

The BOOSTXL-CAPKEYPAD is compatible with the 40-pin BoosterPack plug-in module standard. The

BoosterPack plug-in module headers provide I2C connectivity to a host LaunchPad development kit (SDA

and SCL signals), as well as an open-drain type interrupt request (IRQ) signal, which can be connected to

one of two BoosterPack plug-in module pins to alert a host LaunchPad development kit when new data is

available from the keypad.

Figure 3. BOOSTXL-CAPKEYPAD Pinout

STANDARD TERMS FOR EVALUATION MODULES

1. Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, and/or

documentation which may be provided together or separately (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance

with the terms set forth herein. User's acceptance of the EVM is expressly subject to the following terms.

1.1 EVMs are intended solely for product or software developers for use in a research and development setting to facilitate feasibility

evaluation, experimentation, or scientific analysis of TI semiconductors products. EVMs have no direct function and are not

finished products. EVMs shall not be directly or indirectly assembled as a part or subassembly in any finished product. For

clarification, any software or software tools provided with the EVM (“Software”) shall not be subject to the terms and conditions

set forth herein but rather shall be subject to the applicable terms that accompany such Software

1.2 EVMs are not intended for consumer or household use. EVMs may not be sold, sublicensed, leased, rented, loaned, assigned,

or otherwise distributed for commercial purposes by Users, in whole or in part, or used in any finished product or production

system.

2Limited Warranty and Related Remedies/Disclaimers:

2.1 These terms do not apply to Software. The warranty, if any, for Software is covered in the applicable Software License

Agreement.

2.2 TI warrants that the TI EVM will conform to TI's published specifications for ninety (90) days after the date TI delivers such EVM

to User. Notwithstanding the foregoing, TI shall not be liable for a nonconforming EVM if (a) the nonconformity was caused by

neglect, misuse or mistreatment by an entity other than TI, including improper installation or testing, or for any EVMs that have

been altered or modified in any way by an entity other than TI, (b) the nonconformity resulted from User's design, specifications

or instructions for such EVMs or improper system design, or (c) User has not paid on time. Testing and other quality control

techniques are used to the extent TI deems necessary. TI does not test all parameters of each EVM.

User's claims against TI under this Section 2 are void if User fails to notify TI of any apparent defects in the EVMs within ten (10)

business days after delivery, or of any hidden defects with ten (10) business days after the defect has been detected.

2.3 TI's sole liability shall be at its option to repair or replace EVMs that fail to conform to the warranty set forth above, or credit

User's account for such EVM. TI's liability under this warranty shall be limited to EVMs that are returned during the warranty

period to the address designated by TI and that are determined by TI not to conform to such warranty. If TI elects to repair or

replace such EVM, TI shall have a reasonable time to repair such EVM or provide replacements. Repaired EVMs shall be

warranted for the remainder of the original warranty period. Replaced EVMs shall be warranted for a new full ninety (90) day

warranty period.

3Regulatory Notices:

3.1 United States

3.1.1 Notice applicable to EVMs not FCC-Approved:

FCC NOTICE: This kit is designed to allow product developers to evaluate electronic components, circuitry, or software

associated with the kit to determine whether to incorporate such items in a finished product and software developers to write

software applications for use with the end product. This kit is not a finished product and when assembled may not be resold or

otherwise marketed unless all required FCC equipment authorizations are first obtained. Operation is subject to the condition

that this product not cause harmful interference to licensed radio stations and that this product accept harmful interference.

Unless the assembled kit is designed to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit must

operate under the authority of an FCC license holder or must secure an experimental authorization under part 5 of this chapter.

3.1.2 For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant:

CAUTION

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any interference received, including interference that may cause

undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to

operate the equipment.

FCC Interference Statement for Class A EVM devices

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to

correct the interference at his own expense.

FCC Interference Statement for Class B EVM devices

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more

of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

3.2 Canada

3.2.1 For EVMs issued with an Industry Canada Certificate of Conformance to RSS-210 or RSS-247

Concerning EVMs Including Radio Transmitters:

This device complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may

cause undesired operation of the device.

Concernant les EVMs avec appareils radio:

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation

est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit

accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Concerning EVMs Including Detachable Antennas:

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)

gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type

and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for

successful communication. This radio transmitter has been approved by Industry Canada to operate with the antenna types

listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated.

Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited

for use with this device.

Concernant les EVMs avec antennes détachables

Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et

d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage

radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope

rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le

présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le

manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne

non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de

l'émetteur

3.3 Japan

3.3.1 Notice for EVMs delivered in Japan: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 日本国内に

輸入される評価用キット、ボードについては、次のところをご覧ください。

http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page

3.3.2 Notice for Users of EVMs Considered “Radio Frequency Products” in Japan: EVMs entering Japan may not be certified

by TI as conforming to Technical Regulations of Radio Law of Japan.

If User uses EVMs in Japan, not certified to Technical Regulations of Radio Law of Japan, User is required to follow the

instructions set forth by Radio Law of Japan, which includes, but is not limited to, the instructions below with respect to EVMs

(which for the avoidance of doubt are stated strictly for convenience and should be verified by User):

1. Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal

Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for

Enforcement of Radio Law of Japan,

2. Use EVMs only after User obtains the license of Test Radio Station as provided in Radio Law of Japan with respect to

EVMs, or

3. Use of EVMs only after User obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japan

with respect to EVMs. Also, do not transfer EVMs, unless User gives the same notice above to the transferee. Please note

that if User does not follow the instructions above, User will be subject to penalties of Radio Law of Japan.

【無線電波を送信する製品の開発キットをお使いになる際の注意事項】開発キットの中には技術基準適合証明を受けて

いないものがあります。技術適合証明を受けていないもののご使用に際しては、電波法遵守のため、以下のいずれかの

措置を取っていただく必要がありますのでご注意ください。

1. 電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用

いただく。

2. 実験局の免許を取得後ご使用いただく。

3. 技術基準適合証明を取得後ご使用いただく。

なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。

上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。日本テキサス・イ

ンスツルメンツ株式会社

東京都新宿区西新宿６丁目２４番１号

西新宿三井ビル

3.3.3 Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page

電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧ください。http:/

/www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page

3.4 European Union

3.4.1 For EVMs subject to EU Directive 2014/30/EU (Electromagnetic Compatibility Directive):

This is a class A product intended for use in environments other than domestic environments that are connected to a

low-voltage power-supply network that supplies buildings used for domestic purposes. In a domestic environment this

product may cause radio interference in which case the user may be required to take adequate measures.

4EVM Use Restrictions and Warnings:

4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT

LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS.

4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handling

or using the EVM, including without limitation any warning or restriction notices. The notices contain important safety information

related to, for example, temperatures and voltages.

4.3 Safety-Related Warnings and Restrictions:

4.3.1 User shall operate the EVM within TI’s recommended specifications and environmental considerations stated in the user

guide, other available documentation provided by TI, and any other applicable requirements and employ reasonable and

customary safeguards. Exceeding the specified performance ratings and specifications (including but not limited to input

and output voltage, current, power, and environmental ranges) for the EVM may cause personal injury or death, or

property damage. If there are questions concerning performance ratings and specifications, User should contact a TI

field representative prior to connecting interface electronics including input power and intended loads. Any loads applied

outside of the specified output range may also result in unintended and/or inaccurate operation and/or possible

permanent damage to the EVM and/or interface electronics. Please consult the EVM user guide prior to connecting any

load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative.

During normal operation, even with the inputs and outputs kept within the specified allowable ranges, some circuit

components may have elevated case temperatures. These components include but are not limited to linear regulators,

switching transistors, pass transistors, current sense resistors, and heat sinks, which can be identified using the

information in the associated documentation. When working with the EVM, please be aware that the EVM may become

very warm.

4.3.2 EVMs are intended solely for use by technically qualified, professional electronics experts who are familiar with the

dangers and application risks associated with handling electrical mechanical components, systems, and subsystems.

User assumes all responsibility and liability for proper and safe handling and use of the EVM by User or its employees,

affiliates, contractors or designees. User assumes all responsibility and liability to ensure that any interfaces (electronic

and/or mechanical) between the EVM and any human body are designed with suitable isolation and means to safely

limit accessible leakage currents to minimize the risk of electrical shock hazard. User assumes all responsibility and

liability for any improper or unsafe handling or use of the EVM by User or its employees, affiliates, contractors or

designees.

4.4 User assumes all responsibility and liability to determine whether the EVM is subject to any applicable international, federal,

state, or local laws and regulations related to User’s handling and use of the EVM and, if applicable, User assumes all

responsibility and liability for compliance in all respects with such laws and regulations. User assumes all responsibility and

liability for proper disposal and recycling of the EVM consistent with all applicable international, federal, state, and local

requirements.

5. Accuracy of Information: To the extent TI provides information on the availability and function of EVMs, TI attempts to be as accurate

as possible. However, TI does not warrant the accuracy of EVM descriptions, EVM availability or other information on its websites as

accurate, complete, reliable, current, or error-free.

6. Disclaimers:

6.1 EXCEPT AS SET FORTH ABOVE, EVMS AND ANY MATERIALS PROVIDED WITH THE EVM (INCLUDING, BUT NOT

LIMITED TO, REFERENCE DESIGNS AND THE DESIGN OF THE EVM ITSELF) ARE PROVIDED "AS IS" AND "WITH ALL

FAULTS." TI DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, REGARDING SUCH ITEMS, INCLUDING BUT

NOT LIMITED TO ANY EPIDEMIC FAILURE WARRANTY OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS

FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF ANY THIRD PARTY PATENTS, COPYRIGHTS, TRADE

SECRETS OR OTHER INTELLECTUAL PROPERTY RIGHTS.

6.2 EXCEPT FOR THE LIMITED RIGHT TO USE THE EVM SET FORTH HEREIN, NOTHING IN THESE TERMS SHALL BE

CONSTRUED AS GRANTING OR CONFERRING ANY RIGHTS BY LICENSE, PATENT, OR ANY OTHER INDUSTRIAL OR

INTELLECTUAL PROPERTY RIGHT OF TI, ITS SUPPLIERS/LICENSORS OR ANY OTHER THIRD PARTY, TO USE THE

EVM IN ANY FINISHED END-USER OR READY-TO-USE FINAL PRODUCT, OR FOR ANY INVENTION, DISCOVERY OR

IMPROVEMENT, REGARDLESS OF WHEN MADE, CONCEIVED OR ACQUIRED.

7. USER'S INDEMNITY OBLIGATIONS AND REPRESENTATIONS. USER WILL DEFEND, INDEMNIFY AND HOLD TI, ITS

LICENSORS AND THEIR REPRESENTATIVES HARMLESS FROM AND AGAINST ANY AND ALL CLAIMS, DAMAGES, LOSSES,

EXPENSES, COSTS AND LIABILITIES (COLLECTIVELY, "CLAIMS") ARISING OUT OF OR IN CONNECTION WITH ANY

HANDLING OR USE OF THE EVM THAT IS NOT IN ACCORDANCE WITH THESE TERMS. THIS OBLIGATION SHALL APPLY

WHETHER CLAIMS ARISE UNDER STATUTE, REGULATION, OR THE LAW OF TORT, CONTRACT OR ANY OTHER LEGAL

THEORY, AND EVEN IF THE EVM FAILS TO PERFORM AS DESCRIBED OR EXPECTED.

8. Limitations on Damages and Liability:

8.1 General Limitations. IN NO EVENT SHALL TI BE LIABLE FOR ANY SPECIAL, COLLATERAL, INDIRECT, PUNITIVE,

INCIDENTAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF THESE

TERMS OR THE USE OF THE EVMS , REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES. EXCLUDED DAMAGES INCLUDE, BUT ARE NOT LIMITED TO, COST OF REMOVAL OR

REINSTALLATION, ANCILLARY COSTS TO THE PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES, RETESTING,

OUTSIDE COMPUTER TIME, LABOR COSTS, LOSS OF GOODWILL, LOSS OF PROFITS, LOSS OF SAVINGS, LOSS OF

USE, LOSS OF DATA, OR BUSINESS INTERRUPTION. NO CLAIM, SUIT OR ACTION SHALL BE BROUGHT AGAINST TI

MORE THAN TWELVE (12) MONTHS AFTER THE EVENT THAT GAVE RISE TO THE CAUSE OF ACTION HAS

OCCURRED.

8.2 Specific Limitations. IN NO EVENT SHALL TI'S AGGREGATE LIABILITY FROM ANY USE OF AN EVM PROVIDED

HEREUNDER, INCLUDING FROM ANY WARRANTY, INDEMITY OR OTHER OBLIGATION ARISING OUT OF OR IN

CONNECTION WITH THESE TERMS, , EXCEED THE TOTAL AMOUNT PAID TO TI BY USER FOR THE PARTICULAR

EVM(S) AT ISSUE DURING THE PRIOR TWELVE (12) MONTHS WITH RESPECT TO WHICH LOSSES OR DAMAGES ARE

CLAIMED. THE EXISTENCE OF MORE THAN ONE CLAIM SHALL NOT ENLARGE OR EXTEND THIS LIMIT.

9. Return Policy. Except as otherwise provided, TI does not offer any refunds, returns, or exchanges. Furthermore, no return of EVM(s)

will be accepted if the package has been opened and no return of the EVM(s) will be accepted if they are damaged or otherwise not in

a resalable condition. If User feels it has been incorrectly charged for the EVM(s) it ordered or that delivery violates the applicable

order, User should contact TI. All refunds will be made in full within thirty (30) working days from the return of the components(s),

excluding any postage or packaging costs.

10. Governing Law: These terms and conditions shall be governed by and interpreted in accordance with the laws of the State of Texas,

without reference to conflict-of-laws principles. User agrees that non-exclusive jurisdiction for any dispute arising out of or relating to

these terms and conditions lies within courts located in the State of Texas and consents to venue in Dallas County, Texas.

Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief

in any United States or foreign court.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

IMPORTANT NOTICE FOR TI DESIGN INFORMATION AND RESOURCES

Texas Instruments Incorporated (‘TI”) technical, application or other design advice, services or information, including, but not limited to,

reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to assist designers who are

developing applications that incorporate TI products; by downloading, accessing or using any particular TI Resource in any way, you

(individually or, if you are acting on behalf of a company, your company) agree to use it solely for this purpose and subject to the terms of

this Notice.

TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI

products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,

enhancements, improvements and other changes to its TI Resources.

You understand and agree that you remain responsible for using your independent analysis, evaluation and judgment in designing your

applications and that you have full and exclusive responsibility to assure the safety of your applications and compliance of your applications

(and of all TI products used in or for your applications) with all applicable regulations, laws and other applicable requirements. You

represent that, with respect to your applications, you have all the necessary expertise to create and implement safeguards that (1)

anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that

might cause harm and take appropriate actions. You agree that prior to using or distributing any applications that include TI products, you

will thoroughly test such applications and the functionality of such TI products as used in such applications. TI has not conducted any

testing other than that specifically described in the published documentation for a particular TI Resource.

You are authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include

the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO

ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY

RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or

other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information

regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or

endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the

third party, or a license from TI under the patents or other intellectual property of TI.

TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR

REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING TI RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO

ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL

PROPERTY RIGHTS.

TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY YOU AGAINST ANY CLAIM, INCLUDING BUT NOT

LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF

DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL,

COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR

ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES.

You agree to fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of your non-

compliance with the terms and provisions of this Notice.

This Notice applies to TI Resources. Additional terms apply to the use and purchase of certain types of materials, TI products and services.

These include; without limitation, TI’s standard terms for semiconductor products http://www.ti.com/sc/docs/stdterms.htm), evaluation

modules, and samples (http://www.ti.com/sc/docs/sampterms.htm).

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

Table of contents

Other Texas Instruments Control Unit manuals

Texas Instruments

Texas Instruments UCC25600EVM User manual

Texas Instruments

Texas Instruments PCM1681 User manual

Texas Instruments

Texas Instruments INA290EVM User manual

Texas Instruments

Texas Instruments DAC8811 User manual

Texas Instruments

Texas Instruments BoosterPack BOOSTXL-ADS7142-Q1 User manual

Texas Instruments

Texas Instruments BOOSTXL-TPS652170 User manual

Texas Instruments

Texas Instruments TPS53119EVM-690 User manual

Texas Instruments

Texas Instruments TPS7A78EVM-011 User manual

Texas Instruments

Texas Instruments ADS54J64 User manual

Texas Instruments

Texas Instruments TPA0142 User manual

Texas Instruments

Texas Instruments TPS61310EVM-638 User manual

Texas Instruments

Texas Instruments INA190EVM User manual

Texas Instruments

Texas Instruments UCC27624EVM User manual

Texas Instruments

Texas Instruments PurePath Digital TAS5342DDV6EVM User manual

Texas Instruments

Texas Instruments bq76PL536 EVM User manual

Texas Instruments

Texas Instruments bq26500EVM User manual

Texas Instruments

Texas Instruments TPS53014 User manual

Texas Instruments

Texas Instruments AFE881H1 User manual

Texas Instruments

Texas Instruments TPS2480 EVM User manual

Texas Instruments

Texas Instruments bq35100 Product manual

Texas Instruments

Texas Instruments Piccolo F280049C User manual

Texas Instruments

Texas Instruments ADS5296 User manual

Texas Instruments

Texas Instruments TPS54226EVM-539 User manual

Texas Instruments

Texas Instruments TMCS1101EVM User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual