Texas Instruments LP8864 User manual
User’s Guide
LP8864 Evaluation Module
ABSTRACT
The Texas Instruments LP8864EVM evaluation module helps designers to evaluate the operation and
performance of the LP8864-Q1 device. This document includes a hardware setup instructions, software
instructions, a complete schematic diagram, printed-circuit board (PCB) layout, and bill of materials (BOM) of the
LP8864EVM.
Table of Contents
1 Introduction.............................................................................................................................................................................2
1.1 Features............................................................................................................................................................................. 2
1.2 Applications........................................................................................................................................................................2
2 Test Setup................................................................................................................................................................................3
2.1 LP8864EVM Kit..................................................................................................................................................................3
2.2 System and Equipment Requirements...............................................................................................................................3
2.3 Hardware Setup................................................................................................................................................................. 4
2.4 Software Installation...........................................................................................................................................................4
2.5 Quick Start-Up Procedure.................................................................................................................................................. 5
2.6 Additional GUI Functions................................................................................................................................................... 7
2.7 Instructions for Standalone Evaluation...............................................................................................................................9
3 LP8864EVM Board Layout................................................................................................................................................... 10
4 LP8864EVM Schematic.........................................................................................................................................................11
5 LP8864EVM Bill of Materials................................................................................................................................................12
6 LED Load Board....................................................................................................................................................................14
Trademarks
All trademarks are the property of their respective owners.
www.ti.com Table of Contents
SNVU731 – NOVEMBER 2020
Submit Document Feedback
LP8864 Evaluation Module 1
Copyright © 2020 Texas Instruments Incorporated
1 Introduction
The LP8864EVM helps designers to evaluate the characteristics, operation, and use of the LP8864-Q1 device, a
high-performance LED driver for automotive lighting. The LP8864-Q1 device is a high-efficiency LED driver with
boost controller. The four 200-mA high-precision current sinks support phase shifting that is automatically
adjusted based on the number of channels in use. LED brightness can be controlled globally through the I2C
interface or PWM input.
1.1 Features
The EVM has the following features:
• Up to 48-V VOUT boost controller
• Four high-precision current sinks
• Supports built-in phase-shift PWM dimming, hybrid dimming, current dimming and direct PWM dimming
mode
• LED brightness controlled globally through I2C interface or PWM input
• Extensive fault diagnostics
1.2 Applications
Backlight for:
• Automotive infotainment
• Automotive instrument clusters
• Smart mirrors
• Heads-Up Displays (HUD)
• Central Information Displays (CID)
• Audio-Video Navigation (AVN)
Introduction www.ti.com
2LP8864 Evaluation Module SNVU731 – NOVEMBER 2020
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
2 Test Setup
This section describes how to properly connect and setup the LP8864EVM.
2.1 LP8864EVM Kit
The LP8864EVM kit contains (see Figure 2-1):
• USB2ANY
– Ribbon cable
– USB cable
• LP8864EVM
• LP886X-LEDLOAD-EVM
Figure 2-1. LP8864EVM Kit
2.2 System and Equipment Requirements
• DC power supply: 24 V or higher, 6 A or higher
• LED cable: 5-position ribbon cable
• PC to run GUI software
• GUI software
www.ti.com Test Setup
SNVU731 – NOVEMBER 2020
Submit Document Feedback
LP8864 Evaluation Module 3
Copyright © 2020 Texas Instruments Incorporated
2.3 Hardware Setup
Figure 2-2 shows the hardware setup of the LP8864EVM.
• Connect a 12-V external power supply between the power input terminals VBAT+ and GNDin on the
LP8864EVM
• Connect the USB2ANY module to the PC with the USB cable
• Connect the USB2ANY module to the LP8864EVM with the provided ribbon cable
• Connect the LP8864EVM to the LP886X-LEDLOAD-EVM with a 5-position ribbon cable
Figure 2-2. LP8864EVM Hardware Setup
2.4 Software Installation
Download the GUI software from the LP8864EVM tools folder. Follow the instructions to finish the GUI
installation. Once installed, a shortcut to the GUI is found on the desktop and also in the start-up menu under the
Texas Instruments folder.
Test Setup www.ti.com
4LP8864 Evaluation Module SNVU731 – NOVEMBER 2020
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
2.5 Quick Start-Up Procedure
1. After the hardware is connected successfully, run the GUI software. Turn on the 12-V external power supply.
Select the right device variant of the EVM, which is LP8864, as shown in Figure 2-3.
Figure 2-3. LP8866/4 Family GUI Landing Page
2. Check the connection status button on the bottom left corner of the GUI. The button should be like the one
shown in Figure 2-3. There should be a Hardware Connected message on the status bar next to the button. If it
shows Hardware not Connected, click the button to manually connect the hardware. This button can be used to
connect or disconnect the GUI to the hardware during the evaluation. Besides the connection status button, the
device should be enabled to be connected to the GUI. Ensure the Enable button on the LED Control Page (see
Figure 2-5) is enabled.
www.ti.com Test Setup
SNVU731 – NOVEMBER 2020
Submit Document Feedback
LP8864 Evaluation Module 5
Copyright © 2020 Texas Instruments Incorporated
3. Click the EXPLORE LP8864 button to go to the LP8864EVM GUI home page (see Figure 2-4).
Figure 2-4. LP8864EVM GUI Home Page
4. Click the START button to go to the LED Control page (see Figure 2-5). On the LED Control page, the user
can control all the register-based control functions of the device, like brightness control, current control, sloper
control, dither control, boost synchronization configuration, and spread spectrum configuration.
Figure 2-5. LP8864EVM LED Control Page
Test Setup www.ti.com
6LP8864 Evaluation Module SNVU731 – NOVEMBER 2020
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
2.6 Additional GUI Functions
In the selection tab on the left-hand side, the user can switch between LED Control, Monitor Faults, Diagnostics
and Register Map tabs. This section introduces GUI functions provided in the Monitor Faults, Diagnostics, and
Register Map tabs.
2.6.1 Monitor Faults Page
From the Monitor Faults page (see Figure 2-6), the user has access to LP8864-Q1 fault status bits. Faults can
be cleared by software by clicking the Clear All button. Fault interrupt can be enabled or disabled globally by
toggling the Interrupt All button. Besides that, each fault interrupt and each fault status can be controlled
individually.
Figure 2-6. LP8864EVM Monitor Faults Page
www.ti.com Test Setup
SNVU731 – NOVEMBER 2020
Submit Document Feedback
LP8864 Evaluation Module 7
Copyright © 2020 Texas Instruments Incorporated
2.6.2 Diagnostics Page
From the Diagnostics page (see Figure 2-7), the user can read back the following diagnostics register values
and corresponding device status.
• FSM_LIVE_STATUS: current status of the functional state machine
• PWM_INPUT_STATUS: 16-bit value for detected duty cycle of PWM input signal
• PWM_OUTPUT_STATUS: 16-bit value for configured duty cycle of PWM output signal
• LED_CURRENT_STATUS: 12-bit current DAC code that brightness path is driving to OUT1-4 output
• VBOOST_STATUS: 11-bit boost voltage code that adaptive voltage control loop sending to analog boost
block
• AUTO_PWM_FREQ_SEL: LED PWM frequency value from PWM_SEL resistor detection
• AUTO_LED_STRING_CFG: LED string configuration from LED_SET resistor detection
• AUTO_BOOST_FREQ_SEL: boost switching frequency value from PWM_FSET resistor detection
• MODE_SEL: LED dimming mode value from MODE resistor detection
Figure 2-7. LP8864VM Diagnostics Page
Test Setup www.ti.com
8LP8864 Evaluation Module SNVU731 – NOVEMBER 2020
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
2.6.3 Register Map Page
Figure 2-8 shows the registers map page. All the registers are available on this page. When Auto Read is set to
other than "Off", all the registers will be read automatically and periodically according to the interval time the user
selects. Otherwise, the user needs to click the READ REGISTER button to read the selected register or click the
READ ALL REGISTERS button to read all of the registers.
Clicking on the row of a register automatically updates the corresponding field view on the right side of the page.
The register value can be updated by modifying the hexadecimal value in the Value column or by double-clicking
the corresponding bit in the Bits column. The modified value is effective immediately if "Immediate Write" is
selected in the drop-down menu. When "Deferred Write" is selected, the modified value will not take effect until
the user clicks the WRITE REGISTER button. The value of all the registers can be updated together by clicking
the WRITE ALL REGISTERS button.
Figure 2-8. LP8864EVM Register Map Page
2.7 Instructions for Standalone Evaluation
The LP8864EVM can be used for standalone evaluation (without GUI software and PC connection). To support
standalone mode, it must be modified from its default settings as described in the following list:
1. Mount R20 to pull up EN input.
2. Change pullup and pulldown resistors to select spread spectrum enable (R18) or disable (R25) option.
3. Mount R19 to pull up PWM input for 100% brightness. If brightness needs to be changed from 100%, connect
external PWM source at PWM pin.
The minimum procedures for turning on the LEDs after the previously-listed modifications are as follows:
1. Connect a 12-V external power supply between the power input terminals VBAT+ and GNDin on the
LP8864EVM.
2. Connect the LP886X-LEDLAOD-EVM board (4 strings, 8 LEDs per string) to J10 on the LP8864EVM.
3. Turn on the external power supply.
www.ti.com Test Setup
SNVU731 – NOVEMBER 2020
Submit Document Feedback
LP8864 Evaluation Module 9
Copyright © 2020 Texas Instruments Incorporated
3 LP8864EVM Board Layout
Figure 3-1 and Figure 3-2 illustrate the EVM board layout.
Figure 3-1. LP8864EVM Layout - Top
Figure 3-2. LP8864EVM Layout - Bottom
LP8864EVM Board Layout www.ti.com
10 LP8864 Evaluation Module SNVU731 – NOVEMBER 2020
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
This manual suits for next models
4
Table of contents
Other Texas Instruments Control Unit manuals
Texas Instruments
Texas Instruments ADS1x7xEVM-PDK User manual
Texas Instruments
Texas Instruments TPS54232EVM-415 User manual
Texas Instruments
Texas Instruments LM3643EVM User manual
Texas Instruments
Texas Instruments TPA6100A2 User manual
Texas Instruments
Texas Instruments PCM4222EVM User manual
Texas Instruments
Texas Instruments DAC8742H User manual
Texas Instruments
Texas Instruments LP8863EVM User manual
Texas Instruments
Texas Instruments ISO7220 Series User manual
Texas Instruments
Texas Instruments DAC8574 User manual
Texas Instruments
Texas Instruments LM5164-Q1 EVM User manual
Texas Instruments
Texas Instruments UCC28056EVM-296 User manual
Texas Instruments
Texas Instruments TPS22810EVM User manual
Texas Instruments
Texas Instruments TAS3208EVM-LC User manual
Texas Instruments
Texas Instruments bq34210-Q1 Product manual
Texas Instruments
Texas Instruments TCA8424 User manual
Texas Instruments
Texas Instruments WL1835MODCOM8B User manual
Texas Instruments
Texas Instruments ADS1 7 EVM-PDK Series User manual
Texas Instruments
Texas Instruments TPS65253 User manual
Texas Instruments
Texas Instruments TPS7A78 User manual
Texas Instruments
Texas Instruments INA220 User manual
Popular Control Unit manuals by other brands
Festo
Festo Compact Performance CP-FB6-E Brief description
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Quick installation guide
JS Automation
JS Automation MPC3034A user manual
JAUDT
JAUDT SW GII 6406 Series Translation of the original operating instructions
Spektrum
Spektrum Air Module System manual
BOC Edwards
BOC Edwards Q Series instruction manual
KHADAS
KHADAS BT Magic quick start
Etherma
Etherma eNEXHO-IL Assembly and operating instructions
PMFoundations
PMFoundations Attenuverter Assembly guide
GEA
GEA VARIVENT Operating instruction
Walther Systemtechnik
Walther Systemtechnik VMS-05 Assembly instructions
Altronix
Altronix LINQ8PD Installation and programming manual
