Texas Instruments TUSB1004EVM User manual
User’s Guide
TUSB1004EVM User's Guide
ABSTRACT
The TUSB1004 is a 10 Gbps USB 3.2 quad channel linear redriver for USB Type-A applications. This
doducment goes over how to use and configure the TUSB1004EVM as well as recommendations for system
hardware implementation is described in this document. These recommendations are only guidelines and it is
the designer’s responsibility to consider all system characteristics and requirements. Engineers should refer to
the data sheet for technical details such as device operation, terminal description, and so forth.
Table of Contents
1 Overview..................................................................................................................................................................................2
1.1 What is the TUSB1004EVM?.............................................................................................................................................2
1.2 What is Included in the TUSB1004EVM?.......................................................................................................................... 2
1.3 What Does the EVM Look Like?........................................................................................................................................ 2
2 Hardware Configuration.........................................................................................................................................................3
2.1 Power................................................................................................................................................................................. 3
2.2 Configuration Jumpers....................................................................................................................................................... 3
2.3 CEQ Configuration............................................................................................................................................................. 5
2.4 SSEQ Configuration...........................................................................................................................................................5
2.5 Local I2C Access............................................................................................................................................................... 6
3 Quick Start Guide....................................................................................................................................................................7
4 Schematics..............................................................................................................................................................................8
Trademarks
All trademarks are the property of their respective owners.
www.ti.com Table of Contents
SLLU351 – APRIL 2022
Submit Document Feedback
TUSB1004EVM User's Guide 1
Copyright © 2022 Texas Instruments Incorporated
1 Overview
1.1 What is the TUSB1004EVM?
The TUSB1004EVM is a PCB created to help for customers to evaluate the TUSB1004. The EVM has two
Mirco-B USB receptacles and a stacked dual port USB-A receptacle. The user of the EVM can insert a standard
Micro-B USB cable into the TUSB1004EVM board then conenct the cable to a motherboard or system. The user
can then insert an USB device directly or through an standard USB cable into the USB-A receptacle side of the
EVM board.
1.2 What is Included in the TUSB1004EVM?
The following are the major components of the EVM:
• TUSB1004 device
• Two Micro-B USB receptacle
• Dual Port USB-A receptacle
• Headers for configurating various TUSB1004 features.
1.3 What Does the EVM Look Like?
Figure 1-1. EVM Board
Overview www.ti.com
2TUSB1004EVM User's Guide SLLU351 – APRIL 2022
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
2 Hardware Configuration
2.1 Power
The EVM board can be powered from either Micro-B VBUS pin or from an external power supply through the
barrel jack (J4). The EVM defaults to being powered from a Micro-B Receptacle VBUS (J3).
If powering the EVM from barrel jack, make sure R46 is unpopulated. When removed, a jumper will need to be
placed across JMP13 pins 1 and 2.
Note
Limit VBUS voltage and voltage from barrel jack to no more than 6 V.
2.2 Configuration Jumpers
Multiple jumpers are provided on the EVM for configuration of TUSB1004 and also for probe points.
Following is a list of 4-level jumpers which are used to configure the TUSB1004: JMP3, JMP4, JMP5, JMP6,
JMP7, JMP8, JMP9, and JMP10. The jumper position to select between the different levels is detailed in 4-Level
Configuration Jumper Settings Table.
Note
4-level pins are sampled on rising edge of the EN pin. Therefore, a change in any 4-level pin state will
not be applied until after the EN pin is toggled from low to high.
Table 2-1. 4-Level Configuration Jumper Settings
Jumper Position 4-Level State
Short 5 to 6 0
Short 3 to 4 R
Open F
Short 1 to 2 1
Table 2-2. Jumpers
Jumper Default Position Description
JMP1 Open TEST2/SCL.
If TUSB1004 is configured for I2C mode (MODE pin (JMP13) is floating), then this jumper
is the clock for the local I2C.
If TUSB1004 is configured for pin-strap mode, then Short 3 to 4.
JMP2 Short 3 to 4 AEQENZ/SDA.
If TUSB1004 is configured for I2C mode (MODE pin (JMP13) is floating), then this jumper
is the data for the local I2C.
If TUSB1004 is configured for pin-strap mode, then this jumper selects whether the AEQ
is enabled or not.
• Short 1 to 2: AEQ disabled.
• Short 3 to 4: AEQ enabled.
JMP3 Short 3 to 4 SSEQ1/A1.
If TUSB1004 is configured for I2C mode (MODE pin (JMP13) is floating), then this jumper
along with JMP6 will select the 7-bit I2C target address. Refer to theTUSB1004 data
sheet for details on the available I2C target address options.
If TUSB1004 is configured for pin-strap mode, then this jumper along with JMP6 selects
EQ settings for SSTX receivers. Refer to theTUSB1004 data sheet for details on the EQ
settings.
JMP4 Short 3 to 4 SSEQ0/A0.
If TUSB1004 is configured for I2C mode (MODE pin (JMP13) is floating), then this jumper
along with JMP5 will select the 7-bit I2C target address. Refer to theTUSB1004 data
sheet for details on the available I2C target address options.
If TUSB1004 is configured for pin-strap mode, then this jumper along with JMP5 selects
EQ settings for SSTX receivers. Refer to theTUSB1004 data sheet for details on the EQ
settings.
www.ti.com Hardware Configuration
SLLU351 – APRIL 2022
Submit Document Feedback
TUSB1004EVM User's Guide 3
Copyright © 2022 Texas Instruments Incorporated
Table 2-2. Jumpers (continued)
Jumper Default Position Description
JMP5 Open EQCFG.
If TUSB1004 is configured for I2C mode (MODE pin (JMP13) is floating), then this jumper
must be left floating for normal operation.
If TUSB1004 is configured for pin-strap mode, then this jumper will select EQ options for
SSTX receivers and CRX receivers. Refer to theTUSB1004 data sheet for details.
JMP6 Open AEQCFG.
Selects upper limit for AEQ. Refer to theTUSB1004 data sheet for details.
JMP7 Open CEQ1.
If TUSB1004 is configured for pin-strap mode, then this jumper along with JMP10 selects
EQ settings for CRX receivers. Refer to theTUSB1004 data sheet for details on the EQ
settings.
JMP8 Open CEQ0.
If TUSB1004 is configured for pin-strap mode, then this jumper along with JMP10 selects
EQ settings for CRX receivers. Refer to theTUSB1004 data sheet for details on the EQ
settings.
JMP9 Open VIO_SEL.
Selects whether local I2C interface is at 1.8 V or 3.3 V signalling levels. The default is 3.3
V. Short pins 1 and 2 to select 1.8 V.
JMP10 Short 1 to 2 MODE.
Selects between pin-strap and I2C mode. The default is pin-strap mode.
• Short 1 to 2: Pin-strap mode
• Open: I2C mode.
JMP11 Open SLP_S0#.
JMP12 Open EN.
The EN will enable or disable the TUSB1004.
JMP13 Open Power for TUSB1004.
Selects whether TUSB1004 is powered from J1 VBUS, J3 VBUS or 5 V barrel jack. The
default is power from J3 USB VBUS. Shorting between position 1 and 2 will select the 5 V
barrel jack.
JMP14 Open The local I2C voltage pull-up option. The default is local I2C pull-ups are connected to
TUSB1004s 3.3 V VCC supply. Removing R47 allows for feeding external DC supply for
local I2C.
Hardware Configuration www.ti.com
4TUSB1004EVM User's Guide SLLU351 – APRIL 2022
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
2.3 CEQ Configuration
There are sixteen EQ settings with 0 being the lowest and Fh being the highest.
Table 2-3. USB Connector Facing Port Receiver (CRX1 and CRX2 pins) Equalization Control
Register(s): CEQ1_SEL or
CEQ2_SEL
Equalization Setting #
CEQ1 PIN Level CEQ0 PIN Level
EQ Gain at 5 GHz minus Gain
at 100 MHz
(dB)
0 0 0 Lowest EQ setting.
1 0 R
2 0 F
3 0 1
4 R 0
5 R R
6 R F
7 R 1
8 F 0
9 F R
10 F F
11 F 1
12 1 0
13 1 R
14 1 F
15 1 1 Highest EQ setting
2.4 SSEQ Configuration
There are sixteen EQ settings with 0 being the lowest and Fh being the highest.
Table 2-4. USB Host Facing Port Receiver (SSTX1 and SSTX2 pins) Equalization Control
Register(s): SSEQ1_SEL or SSEQ2_SEL
Equalization Setting # SSEQ1 PIN LEVEL SSEQ0 PIN LEVEL
EQ Gain at 5 GHz minus
Gain at 100 MHz
(dB)
0 0 0 Lowest Setting
1 0 R
2 0 F
3 0 1
4 R 0
5 R R
6 R F
7 R 1
8 F 0
9 F R
10 F F
11 F 1
12 1 0
13 1 R
14 1 F
15 1 1 Highest Setting
www.ti.com Hardware Configuration
SLLU351 – APRIL 2022
Submit Document Feedback
TUSB1004EVM User's Guide 5
Copyright © 2022 Texas Instruments Incorporated
2.5 Local I2C Access
Access to TUSB1004s local I2C signals is provided through the JMP1 and JMP2 connectors. The TUSB1004
supports either 1.8 V and 3.3 V LVCMOS levels. The TUSB1004 VIO_SEL pin (JMP9) is used to select which
voltage level is used. It is important that the I2C signalling levels meet the TUSB1004 LVCMOS levels when I2C
interface is accessed through the connector.
When the MODE pin (JMP10) is floating, TUSB1004 will be enabled for I2C mode. The TUSB1004 I2C target
address is determined by sampled state of SSEQ0/A0 (JMP3) and SSEQ1/A1 (JMP4).
A standalone external I2C host can be connected for debug and control purposes. An example of an external
I2C Host controller is the Total Phase Aardvark I2C/SPI Host Adapter (Total Phase Part#: TP240141).
Table 2-5. TUSB1004 I2C Target Address
SSEQ1/A1
PIN LEVEL
SSEQ0/A0
PIN LEVEL 7-bit Address Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
(W/R)
0 0 44h 1 0 0 0 1 0 0 0/1
0 R 45h 1 0 0 0 1 0 1 0/1
0 F 46h 1 0 0 0 1 1 0 0/1
0 1 47h 1 0 0 0 1 1 1 0/1
R 0 20h 0 1 0 0 0 0 0 0/1
R R 21h 0 1 0 0 0 0 1 0/1
R F 22h 0 1 0 0 0 1 0 0/1
R 1 23h 0 1 0 0 0 1 1 0/1
F 0 10h 0 0 1 0 0 0 0 0/1
F R 11h 0 0 1 0 0 0 1 0/1
F F 12h 0 0 1 0 0 1 0 0/1
F 1 13h 0 0 1 0 0 1 1 0/1
1 0 Ch 0 0 0 1 1 0 0 0/1
1 R Dh 0 0 0 1 1 0 1 0/1
1 F Eh 0 0 0 1 1 1 0 0/1
1 1 Fh 0 0 0 1 1 1 1 0/1
Hardware Configuration www.ti.com
6TUSB1004EVM User's Guide SLLU351 – APRIL 2022
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
3 Quick Start Guide
The following instructions assume the EVM is configured for pin-strap mode and is powered from J3 VBUS.
1. Insert a Micro-B USB cable into J3 on the EVM. Connect the other end of the USB cable to the motherboard.
2. Insert a USB device or USB cable into the lower USB-A receptable of the EVM.
3. The USB device should enumerate. If the USB device does not enumerate, then check that VBUS is at the
appropiate level at D1 pin 1.
4. Insert a Micro-B USB cable into either J1 on the EVM. Connect the other end of the USB cable to the
motherboard.
5. Insert a USB device or USB cable into the upper USB-A receptable of the EVM.
6. The USB device should enumerate. If the USB device does not enumerate, then check that VBUS is at the
appropiate level at D2 pin 1.
The following instructions assume the EVM is configured for the I2C mode and is powered from the barrel jack.
1. Insert +5 V DC power source into the barrel jack (J4).
2. Configure the TUSB1004 through the I2C interface (JMP1 and JMP2).
3. Insert a Micro-B USB cable into either J3 or J1 on the EVM. Connect the other end of the USB cable to the
motherboard.
4. Insert a USB device or USB cable into either USB-A receptable of the EVM. Be sure to connect that the USB
device/cable into the correposding USB-A receptacle (J3 = lower receptaclce, J1 = upper receptacle)
5. The USB device should enumerate. If the USB device does not enumerate, check that VBUS is at the
appropiate level at the correcpsoding USB-A receptacle, pin1 of D1 or D2.
www.ti.com Quick Start Guide
SLLU351 – APRIL 2022
Submit Document Feedback
TUSB1004EVM User's Guide 7
Copyright © 2022 Texas Instruments Incorporated
Table of contents
Other Texas Instruments Computer Hardware manuals
Texas Instruments
Texas Instruments MSP-EXP430F5438 User manual
Texas Instruments
Texas Instruments CC2540 User manual
Texas Instruments
Texas Instruments MSP430F51 User manual
Texas Instruments
Texas Instruments TMS320C6457 User manual
Texas Instruments
Texas Instruments MSP-FET430X110 User manual
Texas Instruments
Texas Instruments C2000 Piccolo LaunchPad User manual
Texas Instruments
Texas Instruments TPS7H4003EVM User manual
Texas Instruments
Texas Instruments 2000 series User manual
Texas Instruments
Texas Instruments TPA6135A2 EVM User manual
Texas Instruments
Texas Instruments LM38020EVM User manual
Texas Instruments
Texas Instruments CC1101DK User manual
Texas Instruments
Texas Instruments TPS65910A Series User manual
Texas Instruments
Texas Instruments TRF0206-SP User manual
Texas Instruments
Texas Instruments TMS320F280 Series User manual
Texas Instruments
Texas Instruments DS250DF810EVM User manual
Texas Instruments
Texas Instruments TPA2013D1 User manual
Texas Instruments
Texas Instruments PHP1500 User manual
Texas Instruments
Texas Instruments TMS320DM643 User manual
Texas Instruments
Texas Instruments DUAL SOCKET PC CARD CONTROLLER PCI1520... User manual
Texas Instruments
Texas Instruments C28 Series User manual
Popular Computer Hardware manuals by other brands
EMC2
EMC2 VNX Series Hardware Information Guide
Panasonic
Panasonic DV0PM20105 Operation manual
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 user manual
Gigabyte
Gigabyte B660M DS3H AX DDR4 user manual
Raidon
Raidon iT2300 Quick installation guide
National Instruments
National Instruments PXI-8186 user manual
