Terrier TFT1 User manual
TFT1 Frost Thermostat
TFT1 Frost Thermostat
Size Pattern No. Pack 1 Qty Pack 2 Qty Code Barcode Price (£) each ex VAT
General Information
TFT1 Frost Thermostat
Code Description A B C
Pegler Yorkshire reserve the right to change specifications
Dimensions
Heating Controls
Pegler Customcare 2 Year Guarantee - Terms & Conditions
Products are subject to a 2 year guarantee that is between Pegler and the final purchaser of the product.
The guarantee is subject to proof of purchase being supplied.
This guarantee does not affect any statutory rights the consumer may have in law.
The guarantee covers manufacturing or material defects and is not applicable where the product is fitted
contrary to conditions of use in our literature.
The guarantee is subject to the following limitations:
1. Damage caused by abusive behaviour and accidental damage to the product are not covered by this
guarantee
The extent of Pegler liability is limited to the cost of the replacement of the defective item and not to fitting or
consequential damages.
Guarantee
Description Minimum Operating
Pressure (bar)
Maximum Cold
Working
Pressure (bar)
Maximum Hot
Working Pressure
(bar)
TFT1 Frost
Thermostat No Minimum
Operating Pressure No Maximum Cold
Working Pressure No Maximum Hot
Working Pressure
Pressure and Temperature
Care
No regular care is required for this product.
Care and Maintenance
No regular cleaning is required. Warning: Great care must be taken to avoid using water or water based
cleaning agent. A barely damp cloth should be used. The Thermostat can be easily cleaned with a soft cloth
wiping over the outer cover only. The programmer should be switched off before cleaning.
Maintenance
No maintenance is required for this product.
For any further help please contact your local heating engineer or a qualified electrician.
If your product is under warranty please contact the Service Support Team on: 0800 1560050.
Regulations
The installation and electrical connections must be carried out by a suitably competent person and all work
must be in accordance with the latest edition of BS7671, IEE Wiring Regulations.
The electricity supply to the installation must be isolated before carrying out installation or maintenance.
Terrier heating controls satisfy the requirements of the Electromagnetic Compatibility Directive (89/336/EEC)
and the Low Voltage Directive (73/23/EEC).
Terrier heating controls are manufactured to a strict quality assurance system in accordance with ISO 9000:
2001.
Regulations
Pegler Yorkshire Group Ltd, St Catherine's Ave, Doncaster, S Yorkshire, DN4 8DF
Telephone: Phone +44 (0) 844 243 4400 Fax: +44 (0) 844 243 9870 Website: www.pegleryorkshire.co.uk
Registered office : Pegler Yorkshire Group Ltd, St Catherine's Ave, Doncaster, S Yorkshire, DN4 8DF Company no : 00401507
INSTALLATION & ASSEMBLY:
The thermostat can be fixed either to a flush mounted connection box, or
directly to the wall, by means of two of the holes on the back part of the
thermostat base. (Important: Locate it on an absolutely flat surface).
1. Remove the single screw as shown below and remove the thermostat dial
cover and outer cover (Fig. 2).
2. Fix the thermostat backplate either directly to the wall or to a suitable flush
mounting box, with 2 suitable screws (Fig. 3).
3. Connect the electric cables to the terminals in accordance with the wiring
diagram (Fig. 4), also shown inside the thermostat cover.
4. Adjust the thermostat temperature setting as in figure 5.
5. Replace the outer and thermostat dial cover.
POSITIONING:
For correct operation the thermostat should
be sited as required where it will protect
vulnerable pipework, radiators or boiler in
the event of the temperature falling to the
freezing point of water. Care should also
be taken to position the thermostat so that it
will detect a rise in temperature once the
heating is switched on by the frost thermostat i.e. where the area protected by the
frost thermostat is heated by radiators or boiler and away from draughts.
23
Screw
Screws
Screws
FROST THERMOSTAT
INSTALLATION INSTRUCTIONS
TFT1
1
38 82
85
WARNING:
Disconnect mains supply before fitting or removing the cover. A switch
having a contact separation of at least 3mm in all poles must be incorporated in
the fixed wiring as a means of fully disconnecting the mains supply.
TECHNICAL DATA:
Range from 5°C to 10°C
Temperature Differential: 0.6°C
Contact Rating 10(3)A
Voltage Rating 230v, 50Hz
Electrical protection Class II IP30
Contact configuration SPST
Wiring must be in accordance with I.E.E. regulations, and the
control fitted by a competent electrician.
This product complies with the essential requirements of the following EC directives:
EMC 89/336/EEC (as amended by 91/263/EEC and 92/31/EEC)
Low Voltage directive: LVD 73/32/EEC 93/68/EEC
Pegler Limited, St. Catherine’s Avenue, Doncaster, South Yorkshire, DN4 8DF
Technical Helpline: 0870 1200285
45
Table of contents
Other Terrier Thermostat manuals
Popular Thermostat manuals by other brands
Saswell
Saswell SAS920XWHB-7-S-RF User manual and warranty card
Aircalo
Aircalo TFP1-ET85P2 operating manual
Honeywell
Honeywell CM721 user manual
Carrier
Carrier DEBONAIR 33CS Installation and operating instructions
Lennox
Lennox iHarmony Zone Thermostat Installation and setup guide
Gemtech
Gemtech GT7000 Operation
