Tennant 9002378 User manual

Other Tennant Floor Machine manuals

Popular Floor Machine manuals by other brands

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Instructions for use

Numatic

Numatic ET 4045 Owner's instructions

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE manual

Mytee

Mytee 8070 Mytee-Lite instructions

Kärcher

Kärcher B 140 R manual

Triple S

Triple S Ace 26T1 user guide

Nilfisk-Advance

Nilfisk-Advance SW 750 Service manual

Tornado

Tornado Marathon 2000 98190 Operation & maintenance manual

Windsor

Windsor ADMIRAL Admiral 8 Specifications

Numatic

Numatic TTB 1117/100 Owner's instructions

Nobles

Nobles Frontier Operator and parts manual

lavina

lavina 21-X user manual

KENT

KENT Edge 28B Service manual

Windsor

Windsor BDP 51/2000C operating instructions

CleanFreak

CleanFreak DURA-18HD Operator's manual

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST How-to guide

BETCO

BETCO PB24 Operator's manual

IPC

IPC CT51-71 BT quick guide

GROUND KIT, STATIC

KIT NO. 9002378 Page1of3

Models: T7 / Speed Scrub Rider

9002379 Rev. 00 (02--06) Tennant Company Customer Service: (800) 553--8033 or (763) 513--2850

This kit is intended for machines manufacturered

before serial #10266229.

The purpose of this kit is to help prevent dam-

age to the newly installed circuit board.

P/N DESCRIPTION QTY.

41141 Washer, Lock, Int--Ext, 0.31 ZN 4

09010 Screw, Hex, M8x1.25X25 SS 1

1030479 Wire Assy, 12.0X.312X.312 Ring Term. 1

KIT CONTENTS

INSTALLATION INSTRUCTIONS:

Installation Time: 1 Hour

TOOLS REQUIRED: 13mm & 1/2” socket

wrenches, continuity tester or VOM meter

1. Park the machine on a clean, level surface.

2. Turn off the machine and remove the key.

3. Unplug the positive battery cable at the red

connector (Figure 1).

WARNING: Electrical Shock Hazard.

Disconnect Battery Cables Before Servicing

Machine.

4. Disconnect the operator seat connector

from the main wire harness and lift the seat

from the machine (Figure 1).

Fig. 1

5. Remove the FaST detergent pack

(if equipped) and remove the FaST deter-

gent holder from the front of the battery

compartment shroud (Figure 2).

Fig. 2

6. Remove the two bolts that secure the

battery compartment shroud and lift the

shroud from the machine (Figure 3).

Fig. 3

7. Remove the bolt and flat washer that

connect the control panel mount to the

actuator mount (Figure 4).

Fig. 4

Page2of3

KIT NO. 9002378

INSTALLATION INSTRUCTIONS -- Continued

9002379 Rev. 00 (02--06) Tennant Company Customer Service: (800) 553--8033 or (763) 513--2850

8. Place one of the star washers from the kit

between the control panel mount and the

actuator mount and reattach the bolt and

flat washer (Figure 5).

Fig. 5

9. Remove one of the two bolts and flat

washers used to mount the actuator

bracket to the main frame. Place one of the

star washers from the kit under the flat

washer and place back onto machine. To

ease reassembly use super glue to hold the

hardware in place (Figure 6).

Fig. 6

10. Reattach the seat support shroud, seat and

the FaST detergent pack and pack holder.

11. Remove bolt and flat washer (A) from pedal

mounting bracket -- discard bolt; save

washer. Replace with one star washer, bolt

and ground wire from the kit, along with the

flat washer that was saved (Figure 7).

A

Fig. 7

12. Route the wire inside the steering column

shroud from (A) to (B) (Figure 8).

A

B

Fig. 8

13. Attach opposite end of the ground wire to

the jack bracket bolt (B) as shown

(Figure 9).

B

Fig. 9

Page3of3

KIT NO. 9002378

INSTALLATION INSTRUCTIONS -- Continued

9002379 Rev. 00 (02--06) Tennant Company Customer Service: (800) 553--8033 or (763) 513--2850

14. If a star washer is not already installed, add

one from the kit, beneath the clamp, on this

seat support stud (Figure 10).

Fig. 10

CHECK CONTINUITY:

NOTE: For the tests below you may need to

scrape a bit of paint off to get down to the

metal for points 2 & 3. This should be done

sparingly and in an inconspicuous location.

1. To check for continuity between the

steering tower and the control board

housing, use either a continuity tester or

VOM set to ohms between points 1 & 2.

The continuity meter should beep or light

up, the VOM should read less than about

10 ohms (Figure 11).

2

1

Fig. 11

2. To check for continuity between the seat

pan and the control board use the same

procedure across points 2 & 3. Note, if you

have continuity between 1 & 2 you can test

across either of points 1 or 2 to point 3

( 1 -- t o -- 3 o r 2 -- t o -- 3 ) .

If you don’t have continuity, make sure that

the star washers broke through the painted

surfaces (Figure 12).

3

2

Fig. 12