Tennant 7100 Training manual
IB 340427 (10-00) 1
No. 340427
Machine: 7100
Published: 10-00/00
System: OPTIONS
INSTRUCTION BULLETIN
NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the Parts
List in the appropriate place in your machine manual for future reference.
Retaining the Parts List will make it easier to reorder individual parts and will
save you the cost of ordering an entire kit.
NOTE: Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials.
Operation instructions for kit number 391049
SYNOPSIS / PROBLEM:
This kit contains the battery rollout cart for the battery rollout kit on the 7100 model scrubber.
Please follow step-by-step instructions.
SPECIAL TOOLS / CONSIDERATIONS: NONE
(Estimated time to complete: 0 hour [battery rollout cart is pre--assembled])
PREPARATION:
(Refer to FIG. 1)
FOR SAFETY: Before leaving or servicing machine, stop on level surface and set parking
brake. Then turn off machine and remove key.
WARNING: Always disconnect battery cables from machine before working
on electrical components.
BATTERY CART OPERATION:
1. Drive the machine to a flat, dry surface.
2. Turn the machine power off and set the parking brake.
FOR SAFETY: Before leaving or servicing
machine, stop on level surface, set parking
brake, turn off machine, and remove key.
3. Lift the operator seat to access the batteries. The
support arm automatically engages when the seat is
lifted all the way up.
4. Unplug the machine connector from the batteries.
IB 340427 (10-00)2
5. Push the battery cart to the right hand side of the
machine. Line up the battery cart locks and the tabs
on the machine. Push the battery cart foward.
6. Lock the battery cart to the machine by closing the
battery cart locks around the machine tabs.
7. Set the battery cart floor lock by stepping down on the
left side of floor lock.
8. Adjust the battery cart rollers before rolling out the
batteries. The battery cart rollers must be the same
height as the machine battery rollers.
Raise battery cart rollers: With a wrench, loosen the
jam nut and turn the bolt clockwise. Then tighten the
jam nuts.
Lower battery cart rollers: With a wrench, loosen the
jam nut and turn the bolt counter--clockwise. Then
tighten the jam nuts.
IB 340427 (10-00) 3
9. Turn the knob on the machine’s battery latch plate
counter--clockwise until the latch plate is free to
move.
10.Raise the battery latch plate up out of the securing
slot.
11. Raise the cart’s battery stop bar by pushing down
on the handle.
12.Grab the battery case slot and pull the battery
case onto the battery cart.
IB 340427 (10-00)4
13.Lower the cart’s battery stop bar by pulling up on the
handle. This will keep the batteries from rolling off the
cart when moving.
14.Release the battery cart from the machine by pushing
the battery cart locks towards the outside of the
battery cart.
15.Release the battery cart floor lock. To release floor
lock, step down on the right side of floor lock.
16.Pull the battery cart away from the machine.
17.Reverse the previous steps to re--install batteries in
the machine.
IB 340427 (10-00) 5
1
23
4
5
6
9
10
11
12
13
14
15
16
17
18
19
20
21
22 23
24
25
26
27
28
29
30
2
3
9
11
12
13
12
13
15
17
18
21
22
23
8
13
12
23 1312
6
7
16
FIG. 1 -- ROLLOUT BATTERY CART ASSEMBLY
IB 340427 (10-00)6
BILL OF MATERIALS FOR ROLLOUT BATTERY CART ASSEMBLY 391049
TENNANT
Ref. Part No. Description Qty.
1 390947 Frame wldt, cart, battery 1
2 222467 Caster, 5.0D wheel 2
3 369373 Caster, battery, cart 2
4 369374 Lock, floor 1
5 03192 Screw, hex, M10 X 1.5 X 30, 8.8 20
6 32492 Washer, flt, 0.38 std 22
7 41430 Nut, hex, lock, M10 X 1.5, NI 2
8 39283 Screw, hex, M10 X 1.5 X 25, 8.8 2
9 369466 Cap, roller shaft 2
10 369462 Frame wldt, mtg, roller 1
11 369371 Roller 6
12 39277 Screw, hex, M08 X 1.25 X 25, 8.8 22
13 32491 Washer, flt, 0.31 std 22
14 391157 Bracket wldt, mtg, latch, R/O 1
15 391162 Plate, latch, battery, R/O, cart 2
16 08709 Nut, hex, lock, M08 X 1.25, NI 8
17 222516 Sleeve 2
18 222648 Grip, handle, round 2
19 369470 Handle wldt, battery cart 1
20 54660 Pin, clevis, 0.75 D X 5.50I 1
21 02141 Pin, clevis, 0.75 D X 4.69I 2
22 55094 Pin, hair cotter, 0.75 D 0.148 wir 3
23 369481 Bumper, rbr, 2.5d 1.00t 0.50h 3
24 369496 Bar, flt, stop, battery, 0.31 1
25 385612 Grip, handle 1
26 58078 Pin, clevis, 0.50 D X 1.25I 1
27 21120 Pin, hair cotter, 0.43 D 0.079 wir 1
28 06416 Screw, hex, M12 X 1.75 X 50, fl 2
29 39313 Nut, hex, std, M12 X 1.75 2
30 391167 Bracket, stop, battery, R/O 1
TENNANT COMPANY
P. O. Box 1452
Minneapolis, MN 55440-1452
Other manuals for 7100
5
This manual suits for next models
1
Table of contents
Other Tennant Floor Machine manuals
Tennant
Tennant 235 User manual
Tennant
Tennant 2360 Product manual
Tennant
Tennant 550 User manual
Tennant
Tennant Litter Hawk 340463 Training manual
Tennant
Tennant ATLV 4300 Training manual
Tennant
Tennant 1240 Product manual
Tennant
Tennant 1465 User manual
Tennant
Tennant S30 Operating and installation instructions
Tennant
Tennant 6500D User manual
Tennant
Tennant 5300 Product manual
Tennant
Tennant T2 User manual
Tennant
Tennant 1200 611468-230V User manual
Tennant
Tennant 5100 Product manual
Tennant
Tennant Nobles V-WD-15S User manual
Tennant
Tennant 110 User manual
Tennant
Tennant 2370 Product manual
Tennant
Tennant NOBLES EX-CAN-15-HP User manual
Tennant
Tennant 5540 Product manual
Tennant
Tennant M17 Series Training manual
Tennant
Tennant 613087 User manual
