TenaControls CARL-CC User manual
Ten^Controls LLC Milford, M@ 01757 US@ www.Ten^Controls.com
Ten^Controls Brings Models to Life
© Cop right 2013 Ten^Controls LLC P^ge 1
Instructions for Model#: CARL-CC, the Standard Car Lighting System
for 19 5 Corvette Stingray 1/8th Scale Model
This unit is completely assembled and tested. The only thing you need to do is connect the led’s
to the connection points as shown below in the Master Wiring Diagram. Then just plug in the 9
volt battery into the holder and throw the micro slide switch on. Hot glue drops on the four
sides of the board works well for locking into place.
Items you will need: Soldering Iron, solder, cutter, wire stripper and additional wiring.
**Note: When using the shrink tubing, you need to only slide the shrink tubing over one leg of
the led to keep it from shorting against the other leg. Then use heat gun or flame from lighter
to heat the shrink tubing until it shrinks around the wire connected to one of the led legs.
How to distinguish a led:
Anode Side (+) Cathode Side (-)
NOTE: This kit could be used with model cars that have individual Low and high beam
buckets.
Ten^Controls LLC Milford, M@ 01757 US@ www.Ten^Controls.com
Ten^Controls Brings Models to Life
© Cop right 2013 Ten^Controls LLC P^ge 2
Master Wiring Diagram
Picture of magnetic switch
Ten^Controls LLC Milford, M@ 01757 US@ www.Ten^Controls.com
Ten^Controls Brings Models to Life
© Cop right 2013 Ten^Controls LLC P^ge 3
igh Beam Lights
1. Two White led’s, LED1-LED2. The Two Anodes (+) of the High Beam led’s, LED1-LED2
connect to the Blue wire from the pc board. Then connect the Cathode (-) of LED1-LED2
to the Orange wire from the pc board. See above diagram.
Rear Driving and Brake Lights
2. Two Red led’s, LED3-LED4. The Two Anodes (+) of the Rear Driving Lights led’s, LED3-
LED4 connect to the White wire from the pc board. Then connect the Cathode (-) of
LED3-LED4 to the Orange wire from the pc board. See above diagram.
Front Driving Lights
3. Two White LED5-LED6. The Two Anodes (+) of the Front Driving Lights led’s, LED5-
LED connect to the Green wire from the pc board. Then connect the Cathode (-) of
LED5-LED to the Orange wire from the pc board. See above diagram.
Right Side Front Directional Light
4. One Orange LED7. Anode (+) of the Right Side Front Directional Light led, LED7
connect to the Yellow wire from the pc board. Then connect the Cathode (-) of LED7 to
the Orange wire from the pc board. See above diagram.
Right Side Rear Directional Light
5. One Red LED8. Anode (+) of the Right Side Rear Directional Light led, LED8 connect to
the Yellow wire from the pc board. Then connect the Cathode (-) of LED8 to the Orange
wire from the pc board. See above diagram.
Ten^Controls LLC Milford, M@ 01757 US@ www.Ten^Controls.com
Ten^Controls Brings Models to Life
© Cop right 2013 Ten^Controls LLC P^ge 4
Left Side Front Directional Light
. One Orange LED9. Anode (+) of the Left Side Front Directional Light led, LED9 connect
to the Black wire from the pc board. Then connect the Cathode (-) of LED9 to the
Orange wire from the pc board. See above diagram.
Left Side Rear Directional Light
7. One Red LED10. Anode (+) of the Left Side Rear Directional Light led, LED10 connect
to the Black wire from the pc board. Then connect the Cathode (-) of LED10 to the
Orange wire from the pc board. See above diagram.
8. Once all the above wiring is done and the Magnetic Switch is mounted in the area of your
choice. Slide the power on Switch to the on position, the front and rear driving lights will
come on. The first Swipe using the enclosed magnet across the Magnetic Switch will turn
the igh Beams “on”. The second Swipe across the Magnetic Switch will turn the Left
Front and Rear Directional “on”. The third Swipe across the Magnetic Switch will turn
the Right Front and Rear Directional “on”. The fourth Swipe across the Magnetic
Switch will turn the Rear Brake Lights “on”. The fifth Swipe across the Magnetic Switch
will turn the Front ead Lights and Rear Driving Lights “on”. The sixth Swipe across the
Magnetic Switch will turn all four directional Lights and Rear Driving Lights “Flashing”
to simulate azard lights. The seventh Swipe across the Magnetic Switch will place the
car lighting system on automatic sequencing through all the above lighting phases. To
return to manual mode just swipe across the Magnetic Switch one more time.
Ten^Controls LLC Milford, M@ 01757 US@ www.Ten^Controls.com
Ten^Controls Brings Models to Life
© Cop right 2013 Ten^Controls LLC P^ge 5
Warranty
TenaControls warrants that the control boards sold meet TenaControls specifications and
are adequately contained, packaged and labeled and conform to the promises and affirmations
of fact made on the container and label. THE FOREGOING WARRANTIES ARE EXCLUSIVE,
AND ARE IN LIEU OF ALL OTHER WARRANTIES (WHETHER WRITTEN, ORAL OR
IMPLIED) INCLUDING WARRANTY OR MERCHANTABILITY IN OTHER RESPECTS THAN
EXPRESSLY SET FORTH ABOVE AND WARRANTY OF FITNESS FOR A PARTICULAR
PURPOSE.
In the event that there is a breach of express warranty by the manufacturer made in
connection with the purchase of this product, if any, the sole remedy of any buyer shall be to
return the product along with original sales receipt, at buyer’s expense for repair (or
replacement of the product if repair is impossible) to the manufacturer’s facility in the
Commonwealth of Massachusetts, located at 22 Hancock Street, Milford, MA 01757. Some
states do not allow the exclusion or limitation of any incidental or consequential damages, so the
above limitation may not apply to you. Nothing herein contained shall be construed to be a
waiver by the manufacturer of any of the obligations imposed upon said buyer under the laws of
the Commonwealth of Massachusetts except as herein specifically stated.
This warranty is enforceable only by the buyer of the product or a person in the buyer’s
immediate family. This warranty is enforceable for a period of FIVE YEARS from the date of
purchase. Some states do not allow limitations on how long an implied warranty lasts, so the
above warranty may not apply to you. This warranty gives you specific legal rights and you may
also have other rights which vary from state to state.
Warranty Void if:
A) Product is altered in any way.
B) Used for other than its intended use.
C) Buyer mishandling.
Table of contents
Other TenaControls Light Fixture manuals
Popular Light Fixture manuals by other brands
Emos
Emos CLASSIC ZY1431T manual
Westinghouse
Westinghouse Outdoor Lighting Fixture owner's manual
Hedler
Hedler C 12 silent Operation manual
Blizzard Lighting
Blizzard Lighting Puck: CSI manual
Energetic Lighting
Energetic Lighting ELYSL-5004 Series installation instructions
Lightmaxx
Lightmaxx Shaft 5R user manual
Cooper Lighting
Cooper Lighting Halo L3232E Specification sheet
Stageline
Stageline ODW-2410RGBW instruction manual
Light Sky
Light Sky Tornado Series user manual
Lightolier
Lightolier Paralyte 2424 PLA2G9LS26U specification
Lightolier
Lightolier Lytespan 83ED17S specification
Lightolier
Lightolier Calculite CS8226 specification