Teltonika RUT240 User manual
Installation Manual - Swiftlane Cellular Router
Installation Manual - Swiftlane Cellular Router 1
Parts information 1
Network 2
Wiring diagrams 3
Option 1: Using an external antenna, for cellular only internet 3
Option 2: Using external antenna and cellular as a backup to primary wired internet
3
Option 3: Using the cellular router without an external antenna 4
Mounting Considerations for External Antenna 6
Height 6
Direction 6
Checking Signal Strength and Connectivity 7
Please use an Ethernet to USB converter so that you can connect to the cellular router
locally on a computer. 7
Router login 8
Setting up cellular failover to the WAN (wired internet) 13
Antenna Location 13
Location of towers 16
Debugging 17
Changing the static IP of the RUT240 17
Checking what devices are connected to the router 18
References 19
Parts information
Type
Product
Name
Summary and Datasheets
Photo
Cellular Router
RUT240
RUT240 cell router website
Omni-direction
al antenna
QuSpot
Link
External antenna with antennas in 4
directions. Utilized in urban environments
with lots of different tower locations nearby
Uni-directional
antenna
QuMax
Link
External antenna with single direction of
antenna. Strongest gain in one direction,
ideal for suburban and remote locations
Passive POE
injector - 24V
DC
UI
Passive
POE 24V
DC
Link
Used to power the RUT240 router, through
the LAN port. Warning: RUT240 does not
support standard POE, which would burn the
router. Only use this passive POE that’s 24V
DC output.
Network
Swiftlane uses AT&T as the primary provider for cellular connectivity. Please check the
general signal strength at the customer site, you can request this information ahead of
time from the customer or during your initial site assessment.
Wiring diagrams
Option 1: Using an external antenna, for cellular only internet
If Swiftlane provided internet is being used as the primary internet service, please follow
these wiring options. An external antenna is strongly recommended in this scenario to
maximize signal strength, especially since the signal can be weaker in server and IDF rooms
Option 2: Using external antenna and cellular as a backup to primary
wired internet
Option 3: Using the cellular router without an external antenna
If the signal strength inside the server room is strong, an external antenna may not be
required, and you can use the antennas that come bundled with the RUT240 router
Mounting Considerations for External Antenna
External antennas should be mounted outside the building with minimal obstruction from
nearby buildings. Identify the location that balances ease of installation with the maximum
unobstructed views, in order to achieve best gain from the antenna
●Balance ease of installation with aesthetic considerations for the building, and
minimal obstructions from nearby building
●For uni-directional antenna, the mount provides a 45 degree rotation angle, in order
to adjust the antenna horizontally and align with the nearby tower
●Use cellmapper.net to identify nearby towers to ensure maximum gain on the
antenna
Height
In general, the taller the antenna is placed, the better it will perform. However, 10-12 ft is a
good installation height to start. This protects it from easy access to vandalism, while also
getting few obstructions to the nearby towers. You can connect the antenna and hold it up
at that height and check the signal strength indicators by connecting to the local
management dashboard over an IP connection. Follow the instructions below to get
familiar with the various parameters for signal strength.
Direction
Omni - directional antennas capture signal strength from all directions so they dont to be
pointing in any specific direction
Uni-directional antennas must be pointed in the general direction of the nearest cell towers
for AT&T. You can use https://www.cellmapper.net/ to insert the full address and look up
nearby 4G towers.
Checking Signal Strength and Connectivity
Please use an Ethernet to USB converter so that you can
connect to the cellular router locally on a computer.
Remove the ethernet cable connected to the non-red side of the white POE injector, and
plug that into your computer.
Set the “connection method” to automatic
This will restart the router. After a few min, you can log back in again and check this page
Go to Status -> Network
It wi
It will show you the signal strength and the “connected Band” in there.
Other manuals for RUT240
8
Table of contents
Other Teltonika Network Router manuals
Teltonika
Teltonika RUT240 User manual
Teltonika
Teltonika RUT955 User manual
Teltonika
Teltonika FM3622 User manual
Teltonika
Teltonika RUT905 User manual
Teltonika
Teltonika RUTX08 User manual
Teltonika
Teltonika RUT523 User manual
Teltonika
Teltonika RUT900 User manual
Teltonika
Teltonika RUT240 User manual
Teltonika
Teltonika RUT200 User manual
Teltonika
Teltonika TRB145 User manual
Teltonika
Teltonika RUT955 User manual
Teltonika
Teltonika RUT240 User manual
Teltonika
Teltonika QSG RUT950 User manual
Teltonika
Teltonika TFT100 User manual
Teltonika
Teltonika RUT230 User manual
Teltonika
Teltonika RUT230 User manual
Teltonika
Teltonika RUT950 LTE User manual
Teltonika
Teltonika RUT905 User manual
Teltonika
Teltonika RUT900 User manual
Teltonika
Teltonika RUT950 LTE User manual
