Teltonika AT1000 User manual
AT1000 Quick Start Guide
V1.0
1
1INTRODUCTION
AT1000 is a terminal with GPS and GSM connectivity, which is able to determine the object’s
coordinates and transfer them via the GSM network. This device is perfectly suitable for applications
where location acquirement of remote objects is needed. Device operates using internal batteries only
and its main applications are tracking of objects which do not have onboard power supply.
1.1 Attention
Personal or portable computers to be connected to the device
must comply with the requirements of DIN EN 60950-1.2003.
Do not disassemble the device more than it is allowed. If the
device is damaged, the power supply cables are not isolated or
the isolation is damaged, before unplugging the power supply, do
not touch the device.
All wireless data transferring devices produce interference that
may affect other devices which are placed nearby.
The device may be fitted only by qualified personnel.
The device must be firmly fastened in the predefined location.
The programming must be performed using a second class PC
(with autonomic power supply).
The device is susceptible to water and humidity in environment
with IP class greater than IP65.
Use only batteries provided by Teltonika. If wrong battery is
used, the device may malfunction. Teltonika takes no
responsibility for device damage caused by third party batteries.
Any installation and/or handling during a lightning storm is
prohibited.
Please use cables provided with AT1000 device.
Teltonika is not responsible for any harm caused by using wrong
cables for PC <-> AT1000 connection.
2
Teltonika reserves the right to change or modify the device in a
way that feels is acceptable and is not in disagreement with terms
and conditions.
Ensure that the batteries are not immersed in water. When
stored, keep the device in a cool and dry place.
Ensure that device and batteries are not exposed to hot surfaces
or direct sunlight.
When transporting, ensure that batteries are safe from metal
articles and do not keep it with metal rings, chains, etc.
Do not damage battery with sharp objects.
Do not try to charge the battery – this may lead to explosion
and/or other harms.
1.2 Instructions of safety
This chapter contains information on how to operate AT1000 safely. By following these
requirements and recommendations, you will avoid dangerous situations. You must read these
instructions carefully and follow them strictly before operating the device!
The device uses a 5V...7.2V DC batteries.
To avoid mechanical damage, it is advised to transport the AT1000 device in an impact-proof
package.
The device is designed to be mounted in a zone of limited access. All related devices must meet
the requirements of standard EN 60950-1.
1.3 Legal Notice
Copyright © 2010 Teltonika. All rights reserved. Reproduction, transfer, distribution or storage
of part or all of the contents in this document in any form without the prior written permission of
Teltonika is prohibited.
Other products and company names mentioned here may be trademarks or trade names of their
respective owners.
3
1.4 Package contents
The AT1000 device is supplied to the customer in a cardboard box containing all the equipment
that is necessary for operation. The package contains:
1. The AT1000 device.
2. Micro USB cable.
3. 2 x 3.6V batteries
4. AT1000 drivers download link paper
2PREPARATION
2.1 Software requirements
Windows XP with SP2 or later, Windows Vista
MS .NET Framework V3.5 or later (http://www.microsoft.com or
http://avl1.teltonika.lt/downloads/tavl/Framework/dotnetfx35setupSP1.zip).
2.2 Drivers
Please download Virtual COM Port drivers from Teltonika website:
http://avl1.teltonika.lt/downloads/AT1000/vcpdriver_v1.1_setup.zip.
IMPORTANT: AT1000 must be connected to PC when installing drivers!
4
3PREPARATION OF THE DEVICE
Open AT1000 device
REMOVE INULATING TAPES
Open SIM card lid and insert the SIM card
Close SIM card lid
Push SIM card lid in the shown direction to lock it and assemble AT1000
5
4Connecting AT1000 to PC
Figure 1. Connecting micro USB cable to AT1000
When AT1000 is connected for the first time to PC, you will be prompted with 'Found New
Hardware' window. Click 'Cancel' to stop automatic installation process.
Figure 2. Found New Hardware window
6
Extract and launch VCPDriver_V1.1_Setup.exe. This driver is used to detect AT1000 device
connected to the computer. Click 'Next' in driver installation window.
Figure 3. Driver installation window
Installation wizard will prompt you with several windows telling that software did not pass
Windows Logo test. Click 'Continue Anyway' button to continue.
Figure 4. Windows Logo pass window
7
Setup will continue installing drivers and will display a window about successful process in the
end. Click 'Finish' to complete setup.
Figure 5. Successful installation window
Note: if drivers did not install successfully or device is not recognized, please make sure that
device is connected to PC and reinstall the drivers.
5Batteries
AT1000 is autonomous device which uses two R14 (ANSI standard) batteries. Batteries used in
this device are single charge Li based type and should have the following parameters:
Voltage: 3.6V
Nominal capacity:5500mAh
Max pulse current not less than:2000mA
Teltonika recommended batteries are available for sale from Teltonika office or distributors.
Only with these batteries correct device operation and (or) prevention of permanent damage to device
is guaranteed.
Warning: use only the same sort of batteries in pair and do not mix old batteries with new ones.
Note:
if inserting the batteries for the first time, make sure insulating tape is
removed! In order to not discharge batteries, please remove them when not using the
device.
8
6Configurator
AT1000 Configurator is software used to setup the device. You can save or read the settings
and read modem IMEI number with it. Please download latest version of AT1000 Configurator from
Teltonika webpage: http://avl1.teltonika.lt/downloads/AT1000/.
To use Configurator with AT1000, make sure that batteries are inserted in the device and it is
connected to PC. In the configurator please choose correct COM port used by device. To find out
which COM port is used follow these steps:
Right-click on 'My Computer' and choose 'Properties';
Go to 'Hardware' and click on 'Device Manager';
Expand 'Ports (COM & LPT)' menu. See COM port number near 'STM Virtual COM
Port'.
Figure 6. STM Virtual COM Port number
9
7CONFIGURATION
Main AT1000 Configurator windows consist of three parts: operations menu (1), global
parameters settings (2) and profiles parameters settings(3).
Figure 7. Main AT1000 Configurator window
7.1 Operations menu
This is a list of commonly used operations such as:
Defaults: choose one of 3 available default settings for the device. Every time you launch
Configurator software, you either have to load settings from file, or load default settings and
modify values manually.
Load from file: click this button to load device settings from file so you don't have to enter
them by hand every time you want to configure the device.
Save to File: click this button to save manually entered setting to a file.
Read from flash: reads settings that are already stored in AT1000 device.
Write to flash: saves the settings to AT1000 memory. Note, that you have to load these settings
from file or enter them manually first.
Get IMEI: reads AT1000 modem IMEI (International Mobile Equipment Identity) number.
Note, that after you connect device to power supply, it takes several seconds to load modem –
only then Configurator is able to read it. Otherwise it will be displayed as 'none'.
COM port: click this drop-down list to choose which COM port is used by AT1000 to connect
to PC. See chapter 6 to find out number of the port.
Refresh button: click it to refresh all available ports on PC. This button is used when you
connect AT1000 to PC while Configurator software is already launched, but it did not detect
Virtual COM Port yet.
Other manuals for AT1000
1
Table of contents
Other Teltonika GPS manuals
Teltonika
Teltonika FMC234 Installation guide
Teltonika
Teltonika FMM125 User manual
Teltonika
Teltonika FMB003 Installation guide
Teltonika
Teltonika FMB010 Installation guide
Teltonika
Teltonika FMB230 User manual
Teltonika
Teltonika FMB003 Installation guide
Teltonika
Teltonika FM3001 User manual
Teltonika
Teltonika FMA202 User manual
Teltonika
Teltonika FMT1 User manual
Teltonika
Teltonika Telematics FMC003 Installation guide
Teltonika
Teltonika FMM00A User manual
Teltonika
Teltonika FM6320 User manual
Teltonika
Teltonika TAT100 User manual
Teltonika
Teltonika TST100 Installation guide
Teltonika
Teltonika TAT140 User manual
Teltonika
Teltonika FMB900 User manual
Teltonika
Teltonika FMB1YX User manual
Teltonika
Teltonika FMB900 Installation and user guide
Teltonika
Teltonika GH5200 User manual
Teltonika
Teltonika FMC920 Installation guide
