Tektronix THDP0100 Manual

THDP0100/0200 & TMDP0200

High Voltage Differential Probes

Installation and Safety Instructions &

Product Documentation CD

ZZZ

*P071289001*

071-2890-01

owned by Tektronix or its subsidiaries or suppliers, and are protected by national

Tektronix products are covered by U.S. and foreign patents, issued and pending.

Information in this publication supersedes that in all previously published

material. Speciﬁcations and price change privileges reserved.

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

Contacting Tektronix

Tektronix, Inc.

14150 SW Karl Braun Drive

P.O. Box 500

Beaverton, OR 97077

USA

For product information, sales, service, and technical support:

In North America, call 1-800-833-9200.

Worldwide, visit www.tektronix.com to ﬁnd contacts in your area.

General Safety Summary

Review the following safety precautions to avoid injury and prevent damage to

this product or any products connected to it.

To avoid potential hazards, use this product only as speciﬁed.

Only qualiﬁed personnel should perform service procedures.

While using this product, you may need to access other parts of a larger system.

Read the safety sections of the other component manuals for warnings and

cautions related to operating the system.

To Avoid Fire or Personal Injury

Ground-Referenced Oscilloscope Use Only. Do not ﬂoat the output of this probe.

The output cable must be connected to an earth-referenced (0 V) oscilloscope.

Avoid Electric Shock. When using probe accessories, never exceed the lowest

rating of the probe or its accessory, whichever is less, including the measurement

category and voltage rating.

Inspect The Probe And Accessories. Before each use, inspect probe and accessories

for damage (cuts, tears, defects in the probe body, accessories, cable jacket, etc.).

Do not use if damaged.

Connect and Disconnect Properly. When using the probe or accessories, keep

ﬁngers behind the ﬁnger guard of probe body and accessories.

Connect and Disconnect Properly. Do not connect or disconnect probes or test

leads while they are connected to a voltage source.

General Safety Summary

Connect and Disconnect Properly. Connect the probe output to the measurement

instrument before connecting the probe to the circuit under test. Connect the

probe input leads one at a time. Make sure accessories are fully mated before

connecting and disconnecting. Disconnect the probe input leads one at a time

from the circuit under test before disconnecting the probe output from the

measurement instrument.

Observe All Terminal Ratings. To avoid ﬁre or shock hazard, observe all ratings

and markings on the product. Consult the product manual for further ratings

information before making connections to the product. Do not apply a potential to

any terminal, including the common terminal, that exceeds the maximum rating

of that terminal.

Avoid Electric Overload. To avoid injury or ﬁre hazard, do not apply potential to

any input, including the reference inputs, that varies from ground by more than

the maximum rating for that input.

Do Not Operate Without Covers. Do not operate this product with covers or panels

removed.

Do Not Operate With Suspected Failures. If you suspect that there is damage to this

product, have it inspected by qualiﬁed service personnel.

Avoid Exposed Circuitry. Do not touch exposed connections and components

when power is present.

General Safety Summary

Do Not Operate in Wet/Damp Conditions.

Do Not Operate in an Explosive Atmosphere.

Keep Product Surfaces Clean and Dry.

TermsinthisManual

These terms may appear in this manual:

WARNING. Warning statements identify conditions or practices that could result

in injury or loss of life.

CAUTION. Caution statements identify conditions or practices that could result in

damage to this product or other property.

General Safety Summary

Symbols and Terms on the Product

These terms may appear on the product:

DANGER indicates an injury hazard immediately accessible as you read the

marking.

WARNING indicates an injury hazard not immediately accessible as you read

the marking.

CAUTION indicates a hazard to property including the product.

The following symbol(s) may appear on the product:

Compliance Information

This section lists the safety and environmental standards with which the

instrument complies.

Safety Compliance

EC Declaration of Conformity – Low Voltage

Compliance was demonstrated to the following speciﬁcation as listed in the

Ofﬁcial Journal of the European Communities:

Low Voltage Directive 2006/95/EC.

EN 61010-031/A1:2008. Safety requirements for electrical equipment for

measurement, control and laboratory use - Part 031: Safety requirements for

hand-held probe assemblies for electrical measurement and test.

Canadian Certiﬁcation

CAN/CSA-C22.2 NO. 61010-031-07/A1:2010, 1st Edition. Safety

requirements for handheld probe assemblies for electrical measurement and

test.

Additional Compliances

IEC 61010-031/A1:2008. Safety requirements for electrical equipment for

measurement, control and laboratory use - Part 031: Safety requirements for

hand-held probe assemblies for electrical measurement and test.

Compliance Information

Pollution Degree Description

A measure of the contaminants that could occur in the environment around

and within a product. Typically the internal environment inside a product is

considered to be the same as the external. Products should be used only in the

environment for which they are rated:

Pollution Degree 1. No pollution or only dry, nonconductive pollution occurs.

Products in this category are generally encapsulated, hermetically sealed, or

located in clean rooms.

Pollution Degree 2. Normally only dry, nonconductive pollution occurs.

Occasionally a temporary conductivity that is caused by condensation must

be expected. This location is a typical ofﬁce/home environment. Temporary

condensation occurs only when the product is out of service.

Pollution Degree 3. Conductive pollution, or dry, nonconductive pollution that

becomes conductive due to condensation. These are sheltered locations where

neither temperature nor humidity is controlled. The area is protected from

direct sunshine, rain, or direct wind.

Pollution Degree 4. Pollution that generates persistent conductivity through

conductive dust, rain, or snow. Typical outdoor locations.

Pollution Degree

Pollution Degree 2 (as deﬁned in IEC 61010-1). Note: Rated for indoor use only.

Compliance Information

Installation & Measurement (Overvoltage) Category Descriptions

Terminals on this product may have different installation or measurement

(overvoltage) category designations. The installation and measurement categories

are:

Overvoltage Category IV. For measurements and installations performed at

the source of low-voltage installation.

Overvoltage Category III. For measurements and installations performed

in the building installation.

Overvoltage Category II. For measurements and installations performed on

circuits directly connected to the low-voltage installation.

Overvoltage Category I. For measurements and installations performed on

circuits not directly connected to MAINS.

Measurement Overvoltage Category

Refer to individual probe ratings for details.

Compliance Information

Environmental Considerations

This section provides information about the environmental impact of the product.

Product End-of-Life Handling

Observe the following guidelines when recycling an instrument or component:

Equipment Recycling. Production of this equipment required the extraction and

use of natural resources. The equipment may contain substances that could be

harmful to the environment or human health if improperly handled at the product’s

end of life. In order to avoid release of such substances into the environment and

to reduce the use of natural resources, we encourage you to recycle this product

in an appropriate system that will ensure that most of the materials are reused or

recycled appropriately.

This symbol indicates that this product complies with the applicable

European Union requirements according to Directives 2002/96/EC and

2006/66/EC on waste electrical and electronic equipment (WEEE)

and batteries. For information about recycling options, check the

Support/Service section of the Tektronix Web site (www.tektronix.com).

Restriction of Hazardous Substances

This product has been classiﬁed as Monitoring and Control equipment, and is

outside the scope of the 2002/95/EC RoHS Directive.

Other manuals for THDP0100

This manual suits for next models

Table of contents

Other Tektronix Test Equipment manuals

Tektronix

Tektronix TCP202A User manual

Tektronix

Tektronix 7844 User manual

Tektronix

Tektronix S-4 User manual

Tektronix

Tektronix TBS2000B Series Manual

Tektronix

Tektronix 454A User manual

Tektronix

Tektronix 7613 User manual

Tektronix

Tektronix DPO70000C Series User manual

Tektronix

Tektronix MSO3000 Series User manual

Tektronix

Tektronix TBS1022 Installation and maintenance instructions

Tektronix

Tektronix 513 User manual

Tektronix

Tektronix 7S12 User manual

Tektronix

Tektronix A605 User manual

Tektronix

Tektronix TDS 420A Service manual

Tektronix

Tektronix 791AD User manual

Tektronix

Tektronix MDO32 Instruction manual

Tektronix

Tektronix SD-14 User manual

Tektronix

Tektronix DPO75902S Reference guide

Tektronix

Tektronix DPO70000SX Series User guide

Tektronix

Tektronix 1A1 User manual

Tektronix

Tektronix 545 Manual

Tektronix

Tektronix 535 Manual

Tektronix

Tektronix TDS 620 User manual

Tektronix

Tektronix SG 505 User manual

Tektronix

Tektronix CSA7000 Series User manual

Popular Test Equipment manuals by other brands

SMART

SMART KANAAD SBT XTREME 3G Series user manual

Agilent Technologies

Agilent Technologies BERT Serial Getting started

Agilent Technologies

Agilent Technologies N3280A user guide

Vernier

Vernier Go Direct Voltage manual

Lifeloc

Lifeloc R.A.D.A.R. quick start guide

Fluke

Fluke T5-600 Service information

Mercury

Mercury TSL01 user manual

MAHA

MAHA MBT Series Original operating instructions

Fuji Electric

Fuji Electric P-61 instruction manual

ETC

ETC SealerAtor user manual

Skyfine

Skyfine ETHYWAY V2 user manual

Appion

Appion G5 Twin Operation manual

PCB Piezotronics

PCB Piezotronics 8159-0112A Installation and operating manual

BW Technologies

BW Technologies MicroDock II user manual

Sun Nuclear

Sun Nuclear 1027 user guide

Biomark

Biomark HPR LITE READER user manual

Hioki

Hioki 3169-20 instruction manual

Ashcroft

Ashcroft ATE-100 operating manual