Tecnoautomazione T181S User manual

EXTERNAL

RECEIVER

RC2

GND

DISABLED

6 SECONDS 12 SECONDS

21 345 6 78 9 10 11 12 21 345 6 78 9 10 11 12

N.C. LIMIT SWITCHES CONTACT NORMALLY

CLOSE N.O. LIMIT SWITCHES CONTACT NORMALLY

OPEN

N.C. INPUTS ENABLED

TERMINAL 1: START FUNCTION

TERMINAL 7: PEDESTRIAN FUNCTION

TERMINAL 1: OPEN FUNCTION

TERMINAL 7: CLOSE FUNCTION

21 345 6 78 9 10 11 12

DIP 3 OFF

21 345 6 78 9 10 11 12

DIP 9 OFF

21 345 6 78 9 10 11 12

DIP 4 OFF

DIP 5 OFF

DIP 6 OFF

DIP 7 OFF / DIP 8 OFF

DIP 10 OFF

DIP 11 OFF

DIP 12 OFF

SLOW DOWN

SOFT START

TESTS

MODES

LIMIT SWITCHES

MOTOR BREAK

MOTOR POWER

21 345 6 78 9 10 11 12 40% 21 345 6 78 9 10 11 12 60% 21 345 6 78 9 10 11 12 80% 21 345 6 78 9 10 11 12 100%

DIP 1 OFF / DIP 2 OFF

AUTOMATIC

CLOSURE

COMMUNITY

MODE +

AUTOMATIC

CLOSURE

STEP-BY-STEP

MODE

STEP-BY-STEP

MODE +

AUTOMATIC

CLOSURE

DIP 1 ON / DIP 2 OFF DIP 1 OFF / DIP 2 ON DIP 1 ON / DIP 2 ON

DIP 3 ON

DIP 7 ON / DIP 8 OFF DIP 7 OFF / DIP 8 ON DIP 7 ON / DIP 8 ON

DIP 9 ON

DIP 10 ON

DIP 11 ON

DIP 12 ON

DIP 4 ON

DIP 5 ON

DIP 6 ON

OFF

INPUTS

2 3 4567

12 3 4567

FLASHING LAMP

MAX 5W

RC1 RC2

STATUSPROGRAM

TIME

GROUND

PHOTO TEST

REMOTE

OUT 2

OUT 1

MOTOR

21 345 6 78 9 10 11 12

GND

10 11 12

OPEN

COM

13 14 15

2019

230 VAC

GND

+ 24 VDC

2A FUSE

RC1

GND

INTERNAL

RECEIVER

ANTENNA

21 345 6 78 9 10 11 12

LAMP 230 VAC

TERMINAL BLOCK:

1. START N.O.

2. STOP N.C.

3. EXTERNAL PHOTOCELL N.C.

4. INTERNAL PHOTOCELL N.C.

5. CLOSING LIMIT SWITCH N.C. / N.O.

6. OPENING LIMIT SWITCH N.C. / N.O.

7. PEDESTRIAN N.O.

8. +VDC / COMMON

9. PHOTOCELLS TEST

10. GND

11.12. FLASHING LAMP

13. MOTOR CLOSE

14. MOTOR COMMON

15. MOTOR OPEN

20.X.19. 230 VAC

DIP-SWITCHES:

1.2. MOTOR POWER

3. SLOW DOWN

4. SOFT START

5. PEDESTRIAN WORKING TIME

6. TESTS

7.8. MODES

9. LIMIT SWITCHES

10. DISABLE NOT WIRED N.C. INPUTS

11. START AND PEDESTRIAN / OPEN AND CLOSE

12. MOTOR BRAKE

LEDs:

S1.S2.S3. CONTROL BOARD STATUS LEDS

RC1.RC2.R1.R2.R3.R4. RADIO LEDS

RC1. SHOWS THAT A SIGNAL HAS BEEN RECEIVED FROM THE INTERNAL RADIO RC1

RC2. SHOWS THAT A SIGNAL HAS BEEN RECEIVED FROM THE EXTERNAL RADIO RC2

R1.START: INDICATES THAT A START BUTTON ON THE REMOTE HAS BEEN PRESSED

R2.STOP: INDICATES THAT A STOP BUTTON ON THE REMOTE HAS BEEN PRESSED

R3. PEDESTRIAN: SHOWS THAT A START PEDESTRIAN BUTTON ON THE REMOTE

HAS BEEN PRESSED

R4. OUT1 ON/OFF: SHOWS THAT A OUT1 BUTTON ON THE REMOTE HAS BEEN

PRESSED

A. C. PROGRAMMING LEDSB.

1.2.3.4.5.6.7. INPUT LEDS AUXILIARY OUTPUTS:

OUT1. ENABLED/DISABLED VIA REMOTE (R4)

OUT2. COURTESY LIGHT / ENABLED DURING

OPENING FOR 3 MINUTES

21 345 6 78 9 10 11 12

T181S. SLIDING GATE CONTROL UNIT. 230 VAC POWER SUPPLY. 433.92 MHz FREQUENCY . 100 STORABLE CODES.

ENABLED.

THE MOTOR WORKS AT THE MAXIMUM

POWER (100%) DURING THE SLOW PHASE.

DISABLED.

THE MOTOR STARTS AT THE POWER

LEVEL SET BY DIP 1 AND DIP 2.

ENABLED.

1.2. SECONDS. THE MOTOR POWER

INCREASES GRADUALLY TILL IT REACHES ITS

MAX VALUE.

PEDESTRIAN WORKING TIME

MOTOR TEST AND PHOTOCELLS TEST

DISABLED MOTOR TEST AND PHOTOCELLS TEST ARE

PERFORMED BEFORE ANY GATE MOVEMENT

DISABLE NOT WIRED N.C. INPUTS

NOT WIRED NC INPUTS DISABLED. WHEN A

N.C. INPUT IS WIRED, IT IS AUTOMATICALLY

ENABLED

START AND PEDESTRIAN / OPEN AND CLOSE

DISABLED ENABLED. MOTOR BREAK ON FOR 0.2

SECONDS IF GATE REACHES LIMIT SWITCH

WITHOUT SLOWING DOWN.

STAND BY, GATE CLOSED

GATE IN OPENING OR CLOSING PHASE, GATE OPEN

CONTROL BOARD IN PROGRAMMING PHASE

PHOTOCELLS TEST ERROR

MOTOR TEST ERROR: CONNECTION ERROR

OR MOTOR OVERHEATING

PROGRAMMING ERROR

BOARD STATUS:S1 S2 S3

POWER SUPPLY START STOP MOTOR

1920

13 14 15

5678910 11 122 3 4

56789

TEST GND

10 11 122 3 4

156789

N.C.

RX RX

GND+VDC

10 11 122 3 4

EXTERNAL PHOTOCELL INTERNAL PHOTOCELL PEDESTRIAN

FLASHING LAMP AUXILIARY OUTPUTS

PHOTOCELLS TRANSMITTER

56789

GND+VDC

10 11 122 3 4

N.C.

5678910 11 122 3 4

5678 9 10 11 122 3 4

CLOSING LIMIT SWITCH

5678910 11 122 3 4

21 345 6 78910 11 12

+VDC

OPENING LIMIT SWITCH

5678910 11 122 3 4

21 345 6 78910 11 12

+VDC

OUT 1 OUT 2

OUT2. COURTESY

LIGHT / ENABLED

DURING OPENING

FOR 3 MINUTES

OUT1. ENABLED/

DISABLED VIA

REMOTE

MAX 5 W

TERMINAL BLOCK CONNECTIONS

OUT1 ON/OFF

R1. OFF

R2. OFF

R3. OFF

R4. ON

RC1

RC2

PEDESTRIAN

R1. OFF

R2. OFF

R3. ON

R4. OFF

STOP

R1. OFF

R2. ON

R3. OFF

R4. OFF

START

R1. ON

R2. OFF

R3. OFF

R4. OFF

MEMORIZE A REMOTE

PRESS AND HOLD THE DESIRED BUTTON ON THE REMOTE, SIMULTANEOUSLY PRESS ONCE THE REMOTE BUTTON ON THE CONTROL BOARD TO

MEMORIZE THE START FUNCTION, PRESS TWICE THE REMOTE BUTTON ON THE BOARD TO MEMORIZE THE STOP FUNCTION, PRESS THREE TIMES

THE REMOTE BUTTON ON THE BOARD TO MEMORIZE THE PEDESTRIAN FUNCTION, PRESS FOUR TIMES THE REMOTE BUTTON ON THE BOARD TO

MEMORIZE THE OUT1 ON/OFF FUNCTION. THE CORRESPONDING LED (R1-START, R2-STOP, R3-PEDESTRIAN, OR R4-OUT1) WILL BE STEADY ON TO

CONFIRM MEMORIZATION.

R1. ON

R2. ON

R3. ON

R4. ON

R1. OFF

R2. OFF

R3. OFF

R4. OFF

R1. OFF

R2. ON

R3. ON

R4. ON

R1. OFF

R2. OFF

R3. ON

R4. ON

R1. OFF

R2. OFF

R3. OFF

R4. ON

ERASE ALL REMOTES

TO ERASE ALL SAVED REMOTES PRESS AND HOLD THE REMOTE BUTTON ON THE BOARD FOR 6 SECONDS. LEDS R1, R2, R3, AND R4 WILL GO ON

STEADY THEN WILL GO OFF INDICATING CORRECT DELETION OF ALL REMOTES.

PRESS AND HOLD THE REMOTE

BUTTON ON THE BOARD FOR

ABOUT 6 SECONDS.

OUT1 ON/OFF

R1. OFF

R2. OFF

R3. OFF

R4. ON

START

R1. ON

R2. OFF

R3. OFF

R4. OFF

STOP

R1. OFF

R2. ON

R3. OFF

R4. OFF

PEDESTRIAN

R1. OFF

R2. OFF

R3. ON

R4. OFF

RC1

RC2

DELETE A REMOTE

PRESS AND HOLD THE DESIRED BUTTON ON THE REMOTE, SIMULTANEOUSLY PRESS FOUR TIMES THE REMOTE BUTTON ON THE CONTROL BOARD

TO DELETE THE START FUNCTION, PRESS THREE TIMES THE REMOTE BUTTON ON THE BOARD TO DELETE THE STOP FUNCTION, PRESS TWICE THE

REMOTE BUTTON ON THE BOARD TO DELETE THE PEDESTRIAN FUNCTION, OR PRESS ONCE THE REMOTE BUTTON ON THE BOARD TO DELETE THE

OUT1 ON/OFF FUNCTION.

PROGRAMMING OF GATE WORKING TIMES. The programming must be operated while the gate is closed.

1 2 3 4

S1 S2 S3 A

S1 S2 S3

PRESS AND HOLD THE

TIME BUTTON FOR 5

SECONDS

PRESS THE TIME BUTTON PRESS THE TIME BUTTON

PRESS THE TIME BUTTON

or a start commande

TO EXIT AND SAVE THE

PAUSE TIME

Led A is steady on. The gate is in the

opening phase. The control board

is acquiring the working me of

motor.

Led A is ﬂashing. The gate connues

the opening phase in slow down

mode. The control board is

acquiring the slow down me of

motor.

Led A and B are steady on. Led C

ﬂashes every second. The control

board is acquiring the pause me. The gate will automacally close

aer the set pause me.

or a start commande or a start commande

MODES

FLASHING LAMP

24 VAC / MAX 5 W

EXTERNAL PHOTOCELLS

CONNECT TO TERMINAL 3.

DURING CLOSING INVERT

THE MOVEMENT.

INTERNAL PHOTOCELLS

CONNECT TO TERMINAL 4.

DURING OPENING INVERT

THE GATE MOVEMENT FOR

2 SECONDS THEN STOP THE

GATE.

ANTENNA

WITH RADIO

CASE

MOTOR

SUGGESTIONS

x x x

FUNCTIONS DESCRIPTION

SLOW DOWN: THE GATE SLOWS DOWN FOR THE SET SLOW DOWN TIME AT THE END OF THE OPENING AND CLOSING PHASES. DURING THE SLOW

DOWN PHASE THE MOTOR WORKS AT ITS MAX POWER.

PEDESTRIAN WORKING TIME: THE GATE OPENS AND CLOSES FOR THE SET PEDESTRIAN WORKING TIME.

SOFT START: THE MOTOR POWER INCREASES GRADUALLY TILL IT REACHES ITS MAX VALUE.

TESTS: THE CORRECT FUNCTIONING OF MOTOR AND PHOTOCELLS ARE CHECKED BEFORE ANY GATE MOVEMENT. IF ONE OF THE TWO TESTS

FAILS THE GATE DOES NOT MOVE. THE LEDS ON THE BOARD INDICATES THE TYPE OF FAILURE. THE MOTOR TEST FAILS WHEN THE MOTOR IS IN

TERMAL PROTECTION OR THERE IS A CONNECTION ERROR. THE PHOTOCELLS TEST FAILS IF TRANSMITTER AND RECEIVER ARE NOT PROPERLY

ALIGNED, IF THERE ARE INSTALLATION ERRORS, OR IF THE PHOTOCELLS ARE DAMAGED.

LIMIT SWITCHES N.C./N.O.: THE LIMIT SWITCHES INPUTS CAN BE NORMALLY CLOSED OR NORMALLY OPEN, DEPENDING ON THE TYPE OF LIMIT

SWITCHES USED.

DISABLE NOT WIRED N.C. INPUTS: DISABLE ALL THE NOT WIRED N.C. INPUTS. IF LATER, A N.C. INPUT IS WIRED, THE BOARD WILL AUTOMATICALLY

ENABLE IT.

MOTOR BREAK: THE BOARD AUTOMATICALLY SLOWS DOWN THE MOTOR IF THE GATE REACHES THE LIMIT SWITCH WITHOUT THE GATE SLOWING

DOWN, PREVENTING MOTOR DAMAGE.

AUTOMATIC CLOSURE: THE GATE AUTOMATICALLY CLOSES AFTER THE SET PAUSE TIME.

• DURING CLOSING, A START OR PEDESTRIAN COMMAND INVERTS THE GATE MOVEMENT.

• DURING OPENING, A START OR PEDESTRIAN COMMAND STOPS THE GATE MOVEMENT.

COMMUNITY PLUS AUTOMATIC CLOSURE: THE GATE AUTOMATICALLY CLOSES AFTER THE SET PAUSE TIME.

• DURING CLOSING, A START OR PEDESTRIAN COMMAND INVERTS THE GATE MOVEMENT.

• DURING OPENING, A START OR PEDESTRIAN COMMAND IS IGNORED.

STEP-BY-STEP: THE GATE STAYS OPEN AT THE END OF THE OPENING PHASE.

• DURING CLOSING AND OPENING, A START OR PEDESTRIAN COMMAND STOPS THE GATE MOVEMENT.

STEP-BY-STEP PLUS AUTOMATIC CLOSURE: THE GATE AUTOMATICALLY CLOSES AFTER THE SET PAUSE TIME.

• DURING CLOSING AND OPENING, A START OR PEDESTRIAN COMMAND STOPS THE GATE MOVEMENT.

TYPICAL INSTALLATION

THE RADIO CASE CAN BE

INSTALLED IN COMBINATION

WITH THE FLASHING LAMP ONE UP.

THE RADIO

MODULE

HOUSED INSIDE

THE RADIO CASE

(RANPC5T).

TO INCREASE THE SIGNAL RANGE DISCONNECT THE RADIO MODULE FROM THE INTERNAL RECEIVER

POSITION AND WIRE IT ON THE TERMINAL BLOCK EXTERNAL RECEIVER POSITION. IF AVAILABLE, WE

SUGGEST YOU USE THE RADIO CASE (CODE RANPC5T).

1. RADIO MODULE CONNECTED IN

INTERNALRECEIVER POSITION

(DEFAULT CONFIGURATION).

2. DISCONNECT THE RADIO

MODULE FROMTHE INTERNAL

RECEIVER POSITION.

3. WIRE THE RADIO MODULE ON THE

TERMINAL BLOCK EXTERNAL RECEIVER

POSITION.

3. WIRE THE RADIO

MODULE ON THE

TERMINAL BLOCK

EXTERNAL

RECEIVER

POSITION.

INTERNAL PROPERTY

MADE IN ITALY

T.A. Tecno Automazione s.r.l. - Via Vicinale snc - 03018 - Paliano - (FR) - Italy - Tel +39 0775 533677 - Fax +39 0775 533299 - [email protected] - www.tecnoautomation.com - www.tecnoautomazione.com

USER MANUAL

T181S

ENG

For private households: Informaon on Disposal for Users of WEEE This symbol on the product(s) and / or accompanying documents means that used electrical and electronicequipment (WEEE)

should not be mixed with general household waste. For proper treatment, recovery and recycling, please take this product(s) to designated collecon points where it will be accepted free of

charge. Alternavely, in some countries, you may be able to return your products to your local retailer upon purchase of an equivalent new product. Disposing of this product correctly will help

save valuable resources and prevent any potenal negave eﬀects on human health and the environment, which could otherwise arise from inappropriate waste handling. Please contact your

local authority for further details of your nearest designated collecon point. Penales may be applicable for incorrect disposal of this waste, in accordance with you naonal legislaon. For

professional users in the European Union If you wish to discard electrical and electronic equipment (EEE), please contact your dealer or supplier for further informaon. For disposal in countries

outside of the European Union This symbol is only valid in the European Union (EU). If you wish to discard this product please contact your local authories ordealer and ask for the correct

method of disposal.

Other Tecnoautomazione Control Unit manuals