TDK-Lambda Genesys Series User manual
Series
Programmable DC Power Supplies
G1.7 - 5kW in 1U 0-600V, 0-500A
PARALLEL KIT INSTRUCTION MANUAL
The manual covers kit options:
G/P-3U-10V
G/P-3U-20-40V
G/P-3U-60-100V
G/P-3U-150-600V
2
1.1
General
Parallel kit is supplied separately from the power supply packing according to order.
The usage of parallel kit is according to customer's needs.
1.2
Advanced Parallel
For parallel connection, refer to advanced parallel chapter in the series User Manual.
1.3
Product Safety Instructions
Safety approvals are valid for single unit only. These are not valid for parallel kit assembly.
When using a paralleling kit with a protective bracket, it must be correctly assembled, as described
further in this document.
1.4
Assembly Instructions
The supplied kit is used for standard and blank panel options. Follow the instructions carefully
according to power supply model.
1.4.1
G/P-3U-10V - Assembly Instructions for three 10V units in Parallel
1.4.1.1
Components List
Image Component Quantity
10‐32x5/16PanHeadScrew,StainlessSteel 12
HelicalSpring‐LockWasher,No.10,StainlessSteel 12
PlainWasher,No.10,StainlessSteel 12
ConnectionPlate3U 2
OutputShort 2
3
Image Component Quantity
M3x4CFlatHeadScrew,NickelPlated 8
ParallelingCable 2
OutputCover 1
BusBarInsulator 2
M3x8SEMSScrew,NickelPlated 6
4
1.4.1.2
Installation Steps
1. Attach connection plates, one on each side of the power supplies, using 12 pan head screws,
12 helical spring-lock washers and 12 plain washers as illustrated in Figure 1.
Figure1:Three10VUnitsConnectionPlates3UAssembly
2. Attach output short plates, one on each triple of terminals, using eight flat head screws as
illustrated in Figure 2.
Figure2:Three10VUnitsOutputShortPlatesAssembly
ConnectionPlate
3U
PlainWasher,No.10,StainlessSteel
HelicalSpring
‐
LockWasher,No.10,StainlessSteel
10‐32x5/16PanHeadScrew,StainlessSteel
Tighteningtorque:25.4‐31.7Lbf‐inch(2.87‐3.58Nm).
M3x4CFlatHeadScrew,NickelPlated
Tighteningtorque:4.7‐5.7Lbf‐inch(0.53‐0.64Nm)
OutputShort
5
3. Connect two paralleling cables from top unit M connector to bottom unit S connector as
illustrated in Figure 3.
Figure3:Three10VUnitsParallelingCableConnection
4. Insert output cover through the cables as illustrated in Figure 4.
Figure4:OutputCoverInsertion
ParallelingCable
Output
Cover
6
5. Assemble two lugs on each bus bar, one on each side, using two hexagon bolts, four plain
washers, two helical spring-lock washers and two hexagon nuts as illustrated in Figure 5.
Figure5:Three10VUnitsLugsAssembly
6. Assemble bus bar insulator prior to output cover assembly. The insulator is flexible and could
be opened in its bottom side. Open the insulator and cover the bus bar by sliding it over the
bus bar, from top to bottom, as illustrated in Figure 6. Repeat for the second bus bar.
Figure6:Three10VUnitsBusBarInsulatorAssembly
Forrecommendedlugsrefer
to seriesSafety&
InstallationManual.
Notsupplied.
HexagonNut,M10,StainlessSteel
HelicalSpring
‐
Lock
Washer,M10,StainlessSteel
PlainWasher,M10,StainlessSteel
M10x25HexagonBolt,StainlessSteel
Tighteningtorque:220‐265Lbf‐inch(24.9‐29.9Nm)
BusBarInsulator
7
7. Fix output cover to the power supplies using six SEMS screws as illustrated in Figure 7.
Figure7:Three10VUnitsOutputCoverAssembly
M3x8SEMSScrew,NickelPlated
Tighteningtorque:4.7
‐
5.7Lbf
‐
inch(0.53
‐
0.64Nm)
8
1.4.2
G/P-3U-20-40V - Assembly Instructions for three 20V-40V units in Parallel
1.4.2.1
Components List
Image Component Quantity
10‐32x5/16PanHeadScrew,StainlessSteel 12
HelicalSpring‐LockWasher,No.10,StainlessSteel 12
PlainWasher,No.10,StainlessSteel 12
ConnectionPlate3U 2
OutputShort 2
M3x4CFlatHeadScrew,NickelPlated 8
ParallelingCable 2
OutputCover 1
9
Image Component Quantity
BusBarInsulator 2
Protection
Insulator
1
M3x8SEMSScrew,NickelPlated 8
10
1.4.2.2
Installation Steps
1. Attach connection plates, one on each side of the power supplies, using 12 pan head screws,
12 helical spring-lock washers and 12 plain washers as illustrated in Figure 8.
Figure8:Three20V‐40VUnitsConnectionPlates3UAssembly
2. Attach output short plates, one on each triple of terminals, using eight flat head screws as
illustrated in Figure 9.
Figure9:Three20V‐40VUnitsOutputShortPlatesAssembly
ConnectionPlate
3U
PlainWasher,No.10,StainlessSteel
HelicalSpring‐LockWasher,No.10,StainlessSteel
10‐32x5/16PanHeadScrew,StainlessSteel
Tighteningtorque:25.4‐31.7Lbf‐inch(2.87‐3.58Nm).
M3x4CFlatHeadScrew,NickelPlated
Tighteningtorque:4.7‐5.7Lbf‐inch(0.53‐0.64Nm)
OutputShort
Other manuals for Genesys Series
11
This manual suits for next models
4
Other TDK-Lambda Power Supply manuals
TDK-Lambda
TDK-Lambda Genesys User manual
TDK-Lambda
TDK-Lambda GENESYS 750W HALF RACK User manual
TDK-Lambda
TDK-Lambda EZA2500W Series Installation guide
TDK-Lambda
TDK-Lambda DPP480-XX-3 User manual
TDK-Lambda
TDK-Lambda CUS200LD User manual
TDK-Lambda
TDK-Lambda Genesys GEN8-300 User manual
TDK-Lambda
TDK-Lambda NV350 User manual
TDK-Lambda
TDK-Lambda 500A User manual
TDK-Lambda
TDK-Lambda GEN 8-400 ABCDE User manual
TDK-Lambda
TDK-Lambda TPF45000 User manual
TDK-Lambda
TDK-Lambda TPS3000 Series User manual
TDK-Lambda
TDK-Lambda EZA2500 Series Installation guide
TDK-Lambda
TDK-Lambda EZA2500WW Series Installation guide
TDK-Lambda
TDK-Lambda Z+ series User manual
TDK-Lambda
TDK-Lambda CUS350M Series User manual
TDK-Lambda
TDK-Lambda DBM20 User manual
TDK-Lambda
TDK-Lambda ZWS-C Series User manual
TDK-Lambda
TDK-Lambda CUT35 Series User manual
TDK-Lambda
TDK-Lambda SWS-L Series User manual
TDK-Lambda
TDK-Lambda FPS1000-12 User manual
