tagarno ZAP STAND User manual
VERSION: 1.0 | FIRMWARE 5.8 | 2023-01-01
CONTENTS
1. INTENDED USE 2
2. WARNINGS 2
3. LASER POINTER WARNING 2
4. YOU HAVE RECEIVED 3
5. ASSEMBLING - ZAP STAND OR ZAP STAND UPGRADE KIT 4
6. ASSEMBLING - ZAP WITH Ø76 ADAPTER KIT 7
7. CONNECTING 10
8. OPERATION 12
9. TECHNICAL SPECIFICATIONS 15
10. PC REQUIREMENTS 17
11. MAINTENANCE 18
12. WARRANTY 18
13. ERGONOMICAL RECOMMENDATIONS 18
14. DECLARATION OF CONFORMITY 19
15. COMPLIANCE STATEMENTS 20
MANUAL | TAGARNO ZAP STAND
Go to tagarno.com/productmanuals to nd manuals and tutorial videos.
2
1. Read the manual before you use the product
2. Use the product only as specied, or the protection supplied by the product can
be compromised
3. Do not position the equipment so that it is difcult to operate the disconnecting
device (appliance inlet of external power supply, equipment input connector)
4. If fluids are spilled on the product, turn the system off immediately by pulling the power
supply out of the electrical outlet
5. In case of re close to the microscope, please turn off and disconnect the system
6. Avoid subjecting the lens to sharp or hard objects
7. Please do not connect the microscope, if visible damages appear
8. Do not dismantle any parts of the microscope, except where noted in the manual
9. Never disassemble or clean internal optical surfaces
10. Use only the power supply provided from TAGARNO
11. Always turn off the system before unplugging, when possible
WARNINGS
The product is a digital magnifying system consisting of a camera unit, PCBs, mechanical
parts and a power supply. The product is intended for marketing worldwide and is designed for
manual visual inspection.
INTENDED USE
Read all safety information before you use the product.
Please pay attention when you see a warning label on the product.
This product is for indoor use only.
You must not discard this electrical/electronic product in domestic household waste.
Please dispose at your local recycling centre.
This product is equipped with a red laser pointer to enable easy alignment of the camera and areas of interest during the inspection process.
This product is a Class 2 laser product that complies with IEC60825-1 international standard for lasers.
These labels appear visible on the product:CAUTION
Follow these safety instructions when using the product.
• Never look directly into the laser aperture
• Do not point towards anyone deliberately
• Leave the laser on only when necessary
• Always turn off power during service and maintenance
• Service may only be performed by trained personnel
appointed by TAGARNO
This label is placed near the laser aperture
The label below is placed on the camera head
1. INTENDED USE
2. WARNINGS
3. LASER POINTER WARNING
3
Get started
Get started
4
7
4. YOU HAVE RECEIVED
Various screws, hex keys
and P clips
Power supply
Rod Base Camera mount
Camera head with lens,
lens ring and cables
Smart guide
Camera adapter ring Extension block and
cylinder
Various screws and hex
keys
Power supply
Camera head with lens,
lens ring and cables
Smart guide Camera adapter ring Extension block and
cylinder
• ZAP STAND / ZAP STAND UPGRADE KIT
• ZAP WITH Ø76 ADAPTER KIT
4
5. ASSEMBLING - ZAP STAND OR ZAP STAND UPGRADE KIT
ASSEMBLING | ZAP STAND OR ZAP STAND UPGRADE KIT (1/3)
If you have a ZAP camera head already mounted on a flexarm,
start by disassembling it by following the ZAP FLEX and ZAP
INLINE manual.
Then, assemble the base and rod with four M5x16 countersunk
screws (bag 1) and place the assembled stand on a sturdy table.
Attach the camera mount to the rod with the three M4x12 screws
(bag 1).
OPTION 1: WITH EXTENDED CAMERA ARM
Mount the extension block on the camera head by using the four
M4x60 screws (bag 2).
Mount the extension cylinder to the extension block with the two
M4x10 screws (bag 2).
5
ASSEMBLING | ZAP STAND OR ZAP STAND UPGRADE KIT (2/3)
Secure the cable bundle with the two P clips (bag 3). If you’re using
a US model, make sure to unmount lens protection cap when using
this microscope.
Place the extended camera arm with mounted camera in the
camera mount and tighten the front and side nger screws (bag
3).
OPTION 2: WITH CAMERA DIRECTLY IN CAMERA HOLDER
Unscrew the lens with your hands and remove the lens ring by
unscrewing the three M3x6 screws.
Screw the camera adapter ring on the camera with the three
countersunk M3x10 screws (bag 4). For correct assembly, the
laser label on the adapter ring must be placed next to the laser
itself.
Then, rescrew the lens on the camera.
6
Place the camera in the camera mount before tightening the front
nger screw (bag 3).
Secure the cable bundle with the two P clips (bag 3). If you’re using
a US model, make sure to unmount lens protection cap when using
this microscope.
ASSEMBLING | ZAP STAND OR ZAP STAND UPGRADE KIT (3/3)
7
ASSEMBLING | ZAP WITH Ø76 ADAPTER KIT (1/3)
Start by removing the microscope head form your current setup,
using the manufacturer’s manual.
6. ASSEMBLING - ZAP WITH Ø76 ADAPTER KIT
OPTION 1: WITH EXTENDED CAMERA ARM
Then, mount the extension block on the camera head by using the
four M4x60 screws (bag 1).
Mount the extension cylinder to the extension block with the two
M4x10 screws (bag 1).
8
Unscrew the lens with your hands and remove the lens ring by
unscrewing the three M3x6 screws.
Screw the camera adapter ring on the camera with the three
countersunk M3x10 screws (bag 3). For correct assembly, the
laser label on the adapter ring must be placed next to the laser
itself.
Then, rescrew the lens on the camera.
ASSEMBLING | ZAP WITH Ø76 ADAPTER KIT (2/3)
OPTION 2: CAMERA DIRECTLY IN HOLDER
Place the extended camera arm with mounted camera in the
camera mount and tighten the front and side nger screws (bag
2).
IMPORTANT! Laser beam attenuator. Unmount lens protection cap
when using this microscope.
9
ASSEMBLING | ZAP WITH Ø76 ADAPTER KIT (3/3)
Place the extended camera arm with mounted camera in the
camera mount and tighten the front and side nger screws (bag
2).
IMPORTANT! Laser beam attenuator. Unmount lens protection cap
when using this microscope.
10
3. 4. 5.1. 2.
Wire Description Type Connect to Cable length Specication
1Output HDMI Type A Monitor 2700mm HDMI out 720p50, 720p60, 1080p25, 1080p30, 1080p50, 1080p60
2USB 3.0 output USB 3.0 Type A Computer 2700mm USB 3.0 Device, Self-powered
3Control box or
foot switch
D-SUB 9-Pin
Female
Control box or
foot switch
3000mm Output: 3.3V 330µA
Use only control boxes supplied by TAGARNO
4Power supply
(DC)
DC Jack Power socket 3000mm Input: 12V 0.5A
Use only the power supply provided by TAGARNO:
Brand/Model: Mean Well/GEM18I12
Protection class II
Input: 100-240V 0.45-0.2A, 50/60Hz
Overvoltage category ll
Output: 12V 1.5A Max
5ESD Ring Terminal
Connector
ESD Grounding
point
3000mm ESD Grounding point
Connect HDMI cable (1), USB 3.0 cable (2), control box or foot
switch (3), power supply (4) and ESD - Electro Static Discharge (5).
WARNING! Do not use force when inserting the cable plugs.
Connect HDMI cable from the microscope to a monitor.
WARNING! Do not connect the HDMI cable to a PC.
* Note: If you’re using the foot switch, connect the cable to the foot switch and then connect the footswitch and control box.
CONNECTING (1/2)
7. CONNECTING
Table of contents
Other tagarno Magnifier manuals
