System air Fantech SHR 8005R User manual
Pool and spa ventilation models
Heat Recovery Ventilators
Installation Manual
Item #: 427684
Rev Date: 2018-02-02
SHR 8005R • SHR 14105R
Your ventilation system should be installed in conformance with the appropriate provincial requirements or, in the absence of
such requirements, with the current edition of the National Building Code, and / or ASHRAE’s “Good Engineering Practices”.
Fantech reserves the right to modify, at any time and without notice, any or all of its products’ features, designs,
components and specifications to maintain their technological leadership position.
Please visit our website www.fantech.net for more detailed technical information.
United States
10048 Industrial Blvd., Lenexa, KS, 66215
Tel.: 800.747.1762 • Fax: 800.487.9915
Canada
50 Kanalflakt Way, Bouctouche, NB, E4S 3M5
Tel.: 800.565.3548 • Fax: 877.747.8116
2
Note Warning/
Important
note
Information Technical
information Practical tip
PLEASE READ THIS MANUAL BEFORE INSTALLING UNIT
Before installation, careful consideration must be given to how this system will operate if connected to any other
piece of mechanical equipment, i.e. a forced air furnace or air handler, operating at a higher static. After installation,
the compatibility of the two pieces of equipment must be confirmed by measuring the airflow’s of the Heat / Energy
Recovery Ventilators. It is always important to assess how the operation of any HRV/ERV may interact with vented
combustion equipment (i.e. Gas Furnaces, Oil Furnaces, Wood Stoves, etc.).
Install a ventilator in a situation where its normal operation, lack of operation or partial failure may result in the
backdrafting or improper functioning of vented combustion equipment!!!
Products are designed and manufactured to provide reliable performance, but they are not guaranteed to be 100%
free of defects. Even reliable products will experience occasional failures, and this possibility should be recognized
by the user. If these products are used in a life support ventilation system where failure could result in loss or injury,
the user should provide adequate back-up ventilation, supplementary natural ventilation or failure alarm system, or
acknowledge willingness to accept the risk of such loss or injury.
Your ventilation system should be installed in accordance with the local building code that is in effect, in absence
of such requirements, it is recommenced to check with local authorities having jurisdiction in your area prior to
installing this product.
3
TABLE OF CONTENTS
INSTALLATION
Location ...........................................................................5
Port Configuration .....................................................................6
Installing Drain Line ....................................................................6
Installing Duct Connections...............................................................7
AIRFLOW BALANCING.........................................................................8
INSTALLING BYPASS MODULE (BPM) ..............................................................9
INSTALLATION EXAMPLES .....................................................................10
MODES OF OPERATION .......................................................................11
Speed Setting .......................................................................12
LOW VOLTAGE CONTROL SYSTEMS ..............................................................13
MAINTENANCE .............................................................................14
ELECTRICAL CONNECTIONS....................................................................15
INSTALLATION VERIFICATION TEST...............................................................17
PARTS LIST
SHR8005R.........................................................................37
SHR14105R........................................................................38
4
Here are the conditions that permit moisture reduction enclosure.
• Ventilation is a year round solution for providing better indoor air quality. Ventilation also provides moisture removing capabilities but may not be
sufficient to control excess moisture year round.
• The pool and its environment must be operated according to the ASHRAE Application handbook guidelines. Failure to do so may lead to excessive
moisture conditions. Consult with our technical support department for further assistance on sizing and guidelines. Unit should be set up and com-
missioned by qualified individuals.
The SHR 8005R contains the following items:
40455 Heat Recovery Ventilator model SHR8005R with installation kit
40452 Bypass module model BPM0820P with installation kit
The SHR 1405R contains the following items:
40445 Heat Recovery Ventilator model SHR14105R with installation kit
40441 Bypass module model BPM0824P with installation kit
Understanding Fantech Product Numbers
SHR 14105R
S = Side Ducting
H = Heat Recovery
R = Remote Control Option
1410 = 1410cfm @0.4 W.G
5 = Five Ports
R = Recirculation
5
Installation
Location
The HRV must be located in a conditioned space where it will be possible to conveniently service the unit. Typically the HRV would be located in the
mechanical room, above a drop ceiling or an area close to the outside wall where the weatherhoods will be mounted. Attic installations are not recom-
mended due to extreme temperatures, and difficulty in performing, required service & maintenance. Care must be taken to locate the recirculation port in
an area that will not cause any unwanted contaminant to be drawn into the living space during recirculation and defrost.
Flexible duct connectors should be installed between the HRV and the galvanized ductwork.
Connecting appliances to the HRV It is not recommended, including:
• clothes dryer
• kitchen exhaust hoods
• combustion venting
• central vacuum system
These appliance may cause lint, dust or grease to collect in the HRV , damaging the unit.
Connecting any of these type of appliances to the HRV will invalidate your warranty
Model A B C D E F G
Kg lbs Kg lbs in. mm. Kg lbs Kg lbs Kg lbs in. mm.
SHR 8005R 23.8 52.5 22.5 49.6 15.4 390 85 187 20 44 18.8 41.3 17.6 448
SHR 14105R 30.4 67 27 60 21.4 544 109 241 27.7 61 24.3 53.5 18 455
A
B
F
E
D
CG
6
Installing Drain Line
Through normal operation and including defrost mode, the HRV may produce some condensation. This water should flow into a nearby drain, or be taken
away by a condensate pump. The HRV and all condensate lines must be installed in a space where the temperature is maintained above freezing point. A
“P” trap should be made in the drain line. This will prevent odors from being drawn back up into the unit.
Install the drain hose, making a “P” trap
The water should be
drained back into the
pool and not wasted
Tape
or Tie Wrap
Drain
Spout
Tee
Connector
Port configuration
The unit has access doors on the front and back. Also, the main control panel may be moved from front to back allowing for ducting layout.
Outdoor or Recirculated Air
Indoor Air
Standard Configuration as shipped from factory.
Outdoor or Recirculated Air
Indoor Air
Indoor Air
Outdoor or Recirculated air
Outdoor or Recirculated air
Indoor Air
Factory Setting. Unit may be easily reversed
in eld.
7
Installing ducts going to / from outside
INSTALLING THE DUCTING TO THE WEATHERHOODS
OUTSIDE WEATHERHOODS – The weatherhoods must have built-in "bird" screens with 6.35 mm (1/4 inch) minimum mesh to prevent birds and rodents
from entering into the ductwork. Do not use smaller mesh as it will be very susceptible to plugging up. The preferred location of the weatherhoods is:
• No less than 3 m (10 ft.) apart from each other.
• At least 457.2 mm (18 inches) snow line or ground level.
• Supply hood must be kept away from sources of contaminant, such as automobile exhaust fumes, gas meters, garbage cans, containers,
cooling towers, tar roofs, etc.
• Avoid prevailing winds, whenever reasonably possible.
The outside perimeter of the weatherhood must be sealed to prevent leakage into the building.
DUCTING FROM THE WEATHERHOODS–TO AND FROM THE HRV – Galvanized sheet metal ducting with sufficient cross section with an integral single piece
of insulated wrap with vapor barrier should be used to connect the HRV to the weatherhoods. The R-value of the insulation should be adequate for
condensation control. Insulated flex duct may be used in moderation, if sized and installed properly. (Consult local codes)
All ducts should be sealed using a good bead of high quality caulking (preferably acoustical sealant) and a high quality aluminum foil tape, or other
approved duct sealant.
8
AThe duct’s airflow velocity
is generally measured
with a magnehelic gauge
and a pitot tube.
• To avoid airflow turbulence
and incorrect readings, the
airflow velocity should be
measured on steel ducting
a minimum of 3 duct
cross-section from the unit
or elbow and before any
transition.
• The balancing procedure consists of measuring the exhaust air leaving the system and the supply air entering the system and ensuring that these
two are equal. A deviation of 10% or less is acceptable.
AIR FLOW BALANCING
A*
Pitot tube and gauge
A professional air balancer should be contacted to commission the system properly. A skilled HVAC Tech may complete the bal-
ance of air providing they possess the proper equipment. Call Fantech Technical support for assistance.
Exhaust Air ducting
The stale air exhaust system is used to draw air from the points in the building where the worst air quality problems occur. ( See installation
examples in the manual.)
Installing ducts to / from inside
Direct Connection to Furnace/ Air handler return duct
• Should you wish to hard duct the supply air directly into the cold air return of the HVAC systems, remember to check the airflow balance of the HRV
with the HVAC systems fan both “on”and “off” to determine that it does not imbalance the HRV more than 10%. Make sure you respect the minimum
distance from the supply air in of the HRV and the HVAC systems.
• It may be necessary to install a separate fresh air supply ductwork system if the heating is other than forced air.
When installing an HRV, the designer and installer should be aware of local codes that may require smoke detectors and/or firestats in the HVAC
or HRV ductwork.
Because an HRV is designed to bring fresh air into the building, structures may require supply voltage interrupt when smoke or flame sensors are
triggered, or when a central fire alarm system is activated.
To maximize airflow in the ductwork system, all ducts should be kept short and have as few bends or elbows as possible. Forty-five degree are
preferred to 90Þ elbows. Use “Y” tees instead of 90Þ elbows whenever possible.
All duct joints must be fastened with screws or duct sealant and wrapped with a quality duct tape to prevent leakage. Aluminum foil duct tape is
recommended.
SUPPLY AIR DUCTING
In buildings without a forced air HVAC systems, fresh air should be supplied to all habitable areas. It should be supplied from high wall or ceiling
locations. The grilles that are to be used should be designed to properly and comfortably sweep cold surfaces.
Optional inline duct heaters may be used to add heat if required. Typically the reheat is best done using a coil off the same boiler that heats the pool water.
9
Installing BYPASS Module (BPM)
Kit content
• 1x BPM assembly
• 1x bracket "A"
• 2x bracket "B"
• 10x Screws
• 1x black extension wire*
• 1x red extentson wire*
* Only used when electrical box is
reversed
Bracket "A"
Bracket "B"
Figure 1
Bracket "B" Installed
Figure 2
Bracket "A Installed
Figure 3
BPM Tilted
Figure 4
BPM Fastening
Figure 5
Bracket "B" tightened
1. Loosely fasten both
brackets “B” to cabinet
using screws in the pilot
holes (Fig. 1). Don’t drive
the screw all the way;
leave about ¼” of thread
for the step 4.
2. Using the same screw
already on the unit,
assemble bracket “A” on
the cabinet (Fig. 2).
3. Install BPM by tilting it
(Fig. 3) so that the hole
on the mounting bracket
“A” lines up with the
pilot hole on top of the
BPM. Secure it with the
fastener and release
the BPM. The tilting
will enable the hole to
line up properly and will
compress the gasket
once released.
4. Assemble the remaining fasteners to secure the BPM
(Fig. 4). Continue to tighten the fasteners holding the
bracket “B” to cabinet in order to compress the gasket
between the BPM and the cabinet (Fig. 5).
Figure 6
Insert damper motor wires
through bushing
Figure 7
HCE Controller, showing "N.O."
terminal location and "C" terminal
location
5. Next route the damper motor wires through the plastic bushing (Fig.6) of
the electrical box and run the wires to the HCE controller on the terminal
marked “N.O.” in the eld marked “DAMPER” and on the terminal marked “C”
in the eld marked “24VAC”. (Fig. 7)
10
Installation examples
INTERIOR WALL
EXTERIOR WALL
EXTERIOR WALL
POOL HRV
MECHANICAL ROOM
EXTERIOR WALL
RECIRCULATION
BACKDRAFT DAMPER
MDH1 Control
EDF1R Control
INTERIOR WALL
EXTERIOR WALL
EXTERIOR WALL
POOL HRV
EXTERIOR WALL
RECIRCULATION
BACKDRAFT DAMPER
RETURN
GRILL
MDH1 Control
EDF1R Control
MECHANICAL ROOM
Installation with Grille
INTERIOR WALL
EXTERIOR WALL
EXTERIOR WALL
POOL HRV
EXTERIOR WALL
AIR HANDLER
RECIRCULATION
BACKDRAFT DAMPER
MDH1 Control
EDF1R Control
MECHANICAL ROOM
HVAC
This manual suits for next models
1
Table of contents
Languages:
Other System air Fan manuals
System air
System air AxZent 400 Manual
System air
System air Villavent VR-400 E User manual
System air
System air Topvex SoftCooler SR11 User manual
System air
System air Living HP Troubleshooting guide
System air
System air SAVE VTC 500 User manual
System air
System air fantech SHR150 User manual
System air
System air AW-EX Series User manual
System air
System air Fantech DPV22-2 User manual
System air
System air EX Series User manual
System air
System air BF QW User manual
System air
System air Fantech PBF Series User manual
System air
System air fantech Pro Series User manual
System air
System air Fantech prioAir 6 User manual
System air
System air KD EC Series Manual
System air
System air RVF 100 Manual
System air
System air KPB Series User manual
System air
System air FANTECH VHR100R User manual
System air
System air KVK Slim 200 Troubleshooting guide
System air
System air Fantech SER200 User manual
System air
System air KFA Manual
Popular Fan manuals by other brands
ELTA FANS
ELTA FANS H03VV-F installation guide
Hunter
Hunter 20714 Owner's guide and installation manual
Emerson
Emerson CARRERA VERANDA CF542ORB00 owner's manual
Hunter
Hunter Caraway Owner's guide and installation manual
Panasonic
Panasonic FV-15NLFS1 Service manual
Kompernass
Kompernass KH 1150 operating instructions
