System air DVG-V-EC Series Guide

IMO_DVG_EC_en_27_11_2013.pdf

DVG-V-EC / DVG-H-EC

F200, F300, F400 EN 12101-3 (400˚C, 120 Min.)

DVG-V-EC/F400 DVG-H-EC/F400

Instructions for transport, installation, commissioning and

maintenance of roof fans DVG-EC

Appendixes:

1 - Mounting of service switch/Mounting of vertical outlets for DVG-V

3, 4 – Accessories – mounting

5 – Bridges in controller and wiring schemes

Controller “Compacto” – instructions

Controller “Invento” - instructions

Page 3

Systemair

d.o.o.

– Špelina ulica 2, SI-2000 Maribor

Tel.: +386 2 46 01 801 – Fax: +386 2 46 01 803

[email protected] – www.systemair.com

- 2 -

Index

Page



1.0

APPLICATION



2.0

TECHNICAL DESCRIPTION



3.0

TRANSPORT

AND STORAGE

3.1 Transport

3.2 Storage



4.0

INSTRUCTIONS FOR INSTALLATION

4.1 Inspection before installation

4.2 Safety instructions for installation, commissioning,

maintenance and controlling

4.3 Installation of the fan

4.4 Instructions for installation



5.0

COMMISSIONING



6.0

APPR

OVAL



7.0

MAINTENANCE AND PERIODIC CONTROL



8.0

SYSTEM MALFUNCTIONS DURING OPERATION



9.0

RANT

Attachment

•

Test protocoll

•Instruction of electric motor

•EC declaration of conformity

- 3 -

1.0 APPLICATION

Smoke extract roof fans are designed for use in powered smoke and heat exhaust

ventilating systems in the event of fire, and ventilating in normal conditions. Ventilated areas

and emergency exits contribute to easier evacuation of people and equipment in the event

of fire, and to faster and more efficient fire extinguishing; they protect the building structure

and equipment against excessive temperatures and decrease fire escalation to the

surrounding areas.

•Fire resistance of fans: 400C, 120 min;

•installation on roofs over heated buildings;

•horizontal outlet (DVG-H) or vertical outlet (DVG-V);

•EC-motor outside air stream;

•daily ventilation of medium with temperature from -20 up to 120°C, supposing

continuously operation, up to 80°C in standstill;

•the fans DVG must not be mounted in explosion hazardous zones;

•0-10V speed control input;

•Modbus controllable;

•Fire mode to disable motor and controller protection in case of fire.

Not intended or unprofessional use can be dangerous for l

ife of user or

third person. It can lead to damage of the fan. The risk for this carries the

operator alone.

2.0 TECHNICAL DESCRIPTION

Casing

Electric motor with impeller is fastened to a sturdy supporting construction. The casing

cover is made of see water resistant aluminium.

Impeller

Impeller of DVG fan is manufactured from galvanized steel. It is fastened with taper bush

and secured screw directly on to the motor shaft. Dynamically balanced in accordance with

ISO 1940 T1, class G6,3.

Electric motor

Fans are serial equipped with EC (electronically commutated) high efficiency electric motors

for single-phase current 200 to 265V, 50/60Hz Hz (sizes 355 and 450), rsp. 342 to 506V,

50/60Hz Hz (sizes 560, 630, 800). Protection class IP 54. Insulation class F.

Max. RPM: 1500 RPM, rsp. 900 RPM at DVG 800.

Detailed description of controller connection and control possibilities please see in attached

instructions of controllers.

3.0 TRANSPORT AND STORAGE

3.1 Transport

Fans are delivered in wooden crates or cardboard boxes. It is recommended to leave the

fans in original packing during transport to the place of installation as well as to load and

unload them carefully to avoid any possible damage. The fans must be transported in a

horizontal position only. During transport and loading/unloading the weight of the fan must

be considered.

- 4 -

On receipt the fan must be visually inspected, and the shipment must be checked for proper

quantity.

3.2 Storage

Store the fans in a dry, weather and dust protected place. If this is impossible, it is important

to raise the fan above the ground surface and cover it with a PE foil.

4.0 INSTRUCTIONS FOR INSTALLATION

4.1 Inspection before installation

Each fan is controlled by the manufacturer before delivery.

After unpacking and before installing, check the following:

•if any eventual damage occurred during transport;

•mounting of service switch and vertical outlets (DVG-V only) up to Appendix 1;

•check by hand if impeller is rotating smoothly.

4.2 Safety instructions for installation, commissioning, maintenance and controlling

Installation and electrical connection must be accomplished only by

authorized technical personnel and in agreement with the valid regulations.

Any hazard of unintended touching the impeller (risk of injury!) has to be

prevented (with a duct long enough or a protective guard)!

Commissioning is allowed only after installation into the ventilation system

or after installation of protective guard (EN 13857). After installation impeller

must not be accessible anymore.

During installation, commissioning, maintenance and controlling,

unauthorized personal should not have access to the fan and installation

place.

Any risk of unintended start-up of the fan and any risk of touching the

impeller during above mentioned works has to be excluded (switch off the

fan and exclude possibility of unintended start-up).

Before removing the casing cover, protective guard on the pressure side or

an eventual protective guard on the suction side make sure the fan is

separated from the mains supply.

Common rules for safety work have to be strictly observed.

4.3 Installation of the fan

•Fans type DVG should be installed outside fire zones (on roofs over heated buildings);

•Fans DVG must not be mounted in explosion hazardous zones;

•Before installation check the carrying capacity and stability of the roof;

•Fans must be installed upright in a vertical position (shaft vertical) and raised above the roof

surface on a base with minimum height of 250 mm (respectively according to expected snow

height);

•The fan shall be fixed to the base with 4 screws on the corners;

•The fan housing should not be deformed during mounting;

•Check, if impeller rotating smoothly;

•Access to the fan for maintenance must be assured.

- 5 -

At installation the dimensions of the fan and possible extension of parts by

the temperature rise has to be considered (provide flexible connection of

appropriate temperature/time class)!

4.4 Instructions for installation

Air ducting system

The suction side of the fan is provided with a connection for flange-type mounting of the air

duct (6 resp. 8 bolts M8 on the base plate). It is recommended to mount fire proof flexible

connections between fan and duct to avoid tension or deformation of the fan base. Flexible

connection should meet temperature/duration class as well as the under pressure at

operation of the fan. In each case smooth rotation of impeller must be insured.

Any risk of unintended start

up of the fan and any risk of touching the

impeller during above mentioned works has to be excluded (switch off the

fan and exclude possibility of unintended start-up).

Connection of the fan to the mains

Electrical connection has to comply with valid local regulations and must be

accomplished only by a qualified electrician. In case of unprofessional

connection guarantee will not be valid. The risk for this carries the operator

alone. Observe attached detailed instructions of motor and controller

supplier – since EC motor built-in, there are warnings for remaining voltage

after supply switched off. Type of permitted RCD protective devices observe

local regulations.

Power supply to motor has to be executed in the service switch placed on the fan. Electric

motor is pre-wired with controller. Control cables should be led through the black tube to

controller. To get to controller dismount the upper cover of the fan.

For control possibilities please see attached instructions of motor and controller supplier.

1~ unit: instructions of controller “Compacto”

3~ unit: instructions of controller “Invento”

The quality and installation of cables for electrical connection must ensure

uninterrupted energy supply, also in case of fire. The electric cable must not

touch or be fastened to the casing of the fan (high temperature!). If danger of

unintended switch off of service switch, it should be locked to guarantee

operation in fire case. Drill hole in position “on” into handle and provide with

a padlock (not supplied with the fan).

- 6 -

Electrical data on the fan nameplate have to comply with the provided mains connection.

Motor protection has to be provided by the installer.

fan

used f

r smoke and heat extract

in case of fire

switch to fire mode

(max. speed, disabled protection of controller and motor) and bridging of

motor protective devices is necessary to assure operation.

Switching on max. speed even after eventual short supply cut off must be assured.

Operating over 1400 to 1500 RPM (size 800: 850 RPM) is not allowed.

5.0 COMMISSIONING

Before initial operation, read through appropriate instructions and check the following:

•Assembling of the fan (fixing, eventual deformations);

•Check all joints for leakage;

•Check if foreign objects were left in the fan or in the connected ducts;

•Check if protective elements are fitted;

•Check the accuracy of the electric wiring and connections to the mains.

Then start the fan for a short period and switch it off again to check the direction of rotation.

It has to comply with the direction of the arrow on the casing of the fan. Check it for proper

operation (smoothly rotating impeller, current, eventual vibrations, noise).

Protective glasses are needed to avoid any injury of the eyes.

Fill in attached control report and file it.

6.0 APPROVAL

It is particularly im

portant to prove the proper function of system and

control devices as well as compliance with requirements of the project and

regulations.

When the system is approved, file the reports. Make sure that only

authorised personnel can handle with on/off switch.

- 7 -

7.0 MAINTENANCE AND PERIODIC CONTROL

Unintended start

up during installing, controlling, maintenance or repair of

the fan has to be prevented!

The following must be controlled periodically (once a year):

1. Check if screws between impeller and hub got loose and tighten them if needed;

2. Tighten the screw between wheel hub and shaft if needed;

3. Remove dirt from the fan impeller if there is any;

4. Check the functionality of protective devices;

5. Check the functionality of control devices;

6. Current during operation;

7. Eventual vibrations;

8. Noise which might appear in el. motor bearings.

The function of the system and control devices has to be checked according to system

maintenance book, minimum every 3 months. Operation at least 15 minutes each time,

once a year 3 hours recommended, if possible.

Checking points 1 to 4 can be done only if the

supply voltage is switched off

and possibility of unintended start-up is excluded.

Parameters of points 5 to 8 must not deviate from the starting values (at installation). In

case that parameters deviate, the electric motor or the impeller have to be replaced or

repaired. This must only be done by an authorised customer service, otherwise the

manufacturer's guarantee is invalid.

The electric motor has to be maintained according to the attached instructions of the

manufacturer of the electric motor.

8.0 SYSTEM MALFUNCTIONS DURING OPERATION

For all inspections, point 4.2. must be considered.

Possible malfunctions and solutions:

The fan doe

not operate Check connection to the mains in service switch. If ok. check connection

to controller.

Air volume is

too low Check operating point and system design.

Under

overvoltage,

overheating,

overcurrent,

locked rotor

etc.

Please see chapter “Troubleshooting” in the instructions of controller.

Noise

Damage to the bearings, impeller blocked or touching the casing.

Get the electric motor or if necessary the complete fan repaired.

Vibrations

Check operating point and system construction. If the actual pressure

drop of the system is higher than supposed, the fan could operate in an

instable area of the fan curve. Inform customer service of the

- 8 -

manufacturer.

Damage or dust layer on impeller.

Clean the impeller, if necessary balance it or replace it.

If the reason for the malfunction can not be clearly determined, inform the customer service

of the manufacturer.

After a case of fire the fan must be checked by the manufacturer.

9.0 GUARANTEE

Guarantee will be valid only if transport, storage, installation, connection and periodical

maintenance have been executed in compliance with the above instructions and local

regulations regarding electric installation and fire protection. For validity of the guarantee

duly filled and signed control report has to be submitted.

It is very important that the installation of the fan is done with all necessary

care, to ensure uninterrupted and safe operation.

Anlage 1. Montage des Revisionsschalters / Montage der Umlenkungsbleche bei DVG-V

Appendix 1. Mounting of service switch / Mounting of vertical outlets for DVG-V

Bilaga 1. Beslag av tjänste- kopplar/beslag av lodlinjeuttag för DVG-V

Приложение 1. П

сковое

тройство -монтаж / Вертикальный выброс -монтаж

Anlage 3. Zubehör - Montage

Appendix 3. Accessories – mounting

Bilaga 3. Tillbehör - installation

иложение 3. П

инадлежности -монтаж

DVG-H

SSG/F

ASG/F

VKG/F

ASSG/F

DVG-H

VKG/F

ASSG/F

FDG/F

DVG-H

VKG/F

SSG/F

ASG/F

ASSG/F

DVG-H

VKG/F

SSGE/F

(FDGE/F)

ASG/F

ASSG/F

This manual suits for next models

Table of contents

Other System air Fan manuals

System air

System air TFC 225 P Installation guide

System air

System air AR Series User manual

System air

System air IV Smart Series User manual

System air

System air Topvex FC Troubleshooting guide

System air

System air Fantech HERO 120H User manual

System air

System air RVK Series Manual

System air

System air Villavent Duo TSL-2 Instruction Manual

System air

System air IV Smart AC Manual

System air

System air K 100 M Manual

System air

System air 445307 User manual

System air

System air KPB Series User manual

System air

System air IV-50 EC User manual

System air

System air AR 350E4 sileo User manual

System air

System air Fantech VER100 User manual

System air

System air AJR Series User manual

System air

System air SAVE VTR 150/K Manual

System air

System air Fantech Rn Series User manual

System air

System air Topvex FC User manual

System air

System air FGS User manual

System air

System air VR 250 ECH/B User manual

System air

System air fantech bathfan Select Fit SF Series Manual

System air

System air TFER K Troubleshooting guide

System air

System air SAVE VSR 150/B User manual

System air

System air AW-EX Series User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual