Swegon GOLD series Quick start guide

GB.MMC480.101021

Reservation för ändringar. www.swegon.com 1

To upgrade the GOLD/COMPACT air handling unit

by means of the MMC/SD card

1. General

The control unit in the GOLD/COMPACT is equipped with

a connection for insertion of an MMC/SD storage card, i.e.

a Multimedia card.

SD cards cannot be used for the GOLD RX/PX/CX/SD if the

control unit is a Version 5.07 or of an earlier version. SD

cards cannot be used for the COMPACT if the control unit

is of Version 1.03 or of an earlier version.

When an MMC/SD card is connected to the control

unit, the control system automatically searches to detect

whether the program version in the card is newer than the

one in the control system.

If it is, a display image will appear where the operator will

have to conﬁrm whether the system is to be upgraded.

The time it takes to upgrade the unit depends on how

many ﬁles differ between the old program and the new

program. This period may vary between one and ten

minutes.

If air handling units with an early version in the hand-held

micro terminal are upgraded, the display images may look

different afterwards. Therefore, two options are shown for

certain display images.

If Image 2a or 2b is shown, wait at least 10 minutes. If the

image remains, switch off the power for 10 seconds. Then

switch it back on again, to restart the control system.

2. Upgrade sequence

Check that the present settings in the air handling unit

agree with those in the Commissioning Report or make

a new note of them. For certain upgrades, involving sub-

stantial changes, it may be necessary to reinstate the origi-

nal factory settings. This will reset any entered settings.

1 Stop the air handling unit. Wait until image 4 appears in

the display on the hand-held micro terminal.

Switch off the safety isolating switch..

2 Fit the MMC/SD card into the card reader, i.e. insert

it, with the text side facing forward, into the slot on the

right-hand side of the control unit. See Image 1.

Switch on the safety isolating switch.

Image 1

Image 2a

Bild 2b

Image 3a

Image 3b

STARTING

UP....

GOLD

RX/PX/CX/SD

GOLD LP/

COMPACT

GB.MMC480.101021

Reservation för ändringar.

2 www.swegon.com

3 Wait for the control system to detect whether there

is a new program in the MMC/SD card and to show the

upgrade display image, see Image 5a or 5b.

(This will take about 1 minute if there are any new ﬁles,

otherwise the image will not appear on the display

screen.)

4 Press the Enter button on the hand-held micro terminal

to conﬁrm that the system is to be upgraded.

5 While the unit is being upgraded, the display image will

switch to Image 6a or if the unit has an older program ver-

sion to Image 6b. After about 10 seconds, Image 2b will

appear on the screen.

6 If the unit has a newer program version, the display

image will switch to Image 3a when the air handling unit

reboots (reads the new program). For older program ver-

sions, Image 2b will also be shown here.

7 When upgrading a GOLD RX/PX/CX/SD, from Program

Version 1.02 – 2.02 to Program Version 3.03 or later. The

program will be transferred in two steps. When Image 4

reappears, wait until zero point calibration is completed

and Image 5a or 5b is displayed again (about 3 minutes).

Continue again from Item 3.

8 Isolate the current and remove the MMC/SD circuit card

when image 7 is displayed. (If frequency inverters are

used, GOLD RX/PX/CX/SD version C, and the DIP switch is

set to the ON position, the current must be isolated for at

least 1 minute after updating).

9 Folllow the instructions received from OSS (Order Sales

Support), or reset the unit to reinstate its Factory Settings

so that all the parameters will be correct. Do this under

Installation/Hand-held terminal/Basic Settings/Factory Set-

tings. All the settings, except for the settings for commu-

nication and alarm priorities, will then return to the factory

preset values.

(When upgrading a GOLD RX/PX/CX/SD to Program Ver-

sion 3.03 or later, all the alarm priorities will be reset to

the factory preset values.

10 Check or set the desired functions and set points.

11 Start the air handling unit in the desired operating

mode.

* GOLD * TUE 13:34

STOP

MANUAL OPERATION

STOP?

Image 4

* PROGRAM TRANSFER *

TRANS. NEW VERSION

READ VERSIONS.

CANCEL

Image 5a

Image 5b

* PROGRAM TRANSFER *

PRESENT VER: 1.02

TRANS. NEW VER: 1.03

CANCEL

TRANSFERRING

NEW PROGRAM....

Image 6a

Image 6b

* PROGRAM TRANSFER *

TRANSFERRING

NEW PROGRAM....

PROGRAM TRANSFERRED

SWITCH MAINS OFF AND

UNMOUNT MMC/SD

CARD OR PRESS X.

Image 7

Other manuals for GOLD series

This manual suits for next models

Other Swegon Fan manuals

Swegon

Swegon GOLD RX User manual

Swegon

Swegon WISE Kite Ceiling a User manual

Swegon

Swegon CRM Series Guide

Swegon

Swegon TBXZ-3-42 User manual

Swegon

Swegon ADAPT Sphere c User manual

Swegon

Swegon EAGLE Free g Guide

Swegon

Swegon CASA R120 Instruction Manual

Swegon

Swegon CASA R85 User manual

Swegon

Swegon PARAGON-X m User manual

Swegon

Swegon EAGLE Wall b Guide

Swegon

Swegon EAGLE CCa Guide

Swegon

Swegon PELICAN Ceiling User manual

Swegon

Swegon ADAPT Colibri c Guide

Swegon

Swegon CASA R120 Operator's manual

Swegon

Swegon REACT V SKNXa User manual

Swegon

Swegon GOLD SD 004/005 User manual

Swegon

Swegon WISE Colibri Ceiling a User manual

Swegon

Swegon ILTO 400M Parts list manual

Swegon

Swegon EAGLE Ceiling User manual

Swegon

Swegon PELICAN Ceiling Extract a Guide

Swegon

Swegon ADAPT Extract Guide

Swegon

Swegon GOLD PX Series Troubleshooting guide

Swegon

Swegon KDYa Series Guide

Swegon

Swegon SILVER C User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual