Swegon ADAPT Extract d Guide

ADAPTTM Extract d

Installation – Commissioning – Maintenance 20130610 / Art. No. 1545218

Installation

1. The commissioning box can be suspended from a

ceiling and connected to a duct system. Use hanger

system (A) or (B), see ﬁgure 2.

2. Plug the connector of the commissioning box into the

top of the diffuser (C, ﬁgure 2). The front plate does

not normally need to be removed when plugging the

connector in the diffuser.

3. Mount the diffuser into the outlet of the commission-

ing box. Make sure that the orientation of the sensor

module aligns with the extension of the room, see ﬁgure 1.

4. Fixate and secure the diffuser with screws or pop rivets.

Readjust the hanger rods of the commissioning box if

necessary, so that the air diffuser is ﬁrmly positioned

against the false ceiling.

Pins

insulation

Figure 2. ADAPT Extract, installation.

Figure 1. The orientation of the sensor module in a room or in

an ofﬁce module. The LED’s of the sensor should be aligned with

the extension of the room in a straight line, facing the short sides

of the room as shown by the arrow in the ﬁgure.

Disassembly of the front plate

1. Dismantle the front plate from the diffuser body by

turning the three springs which enables separation of

the front plate from the pins of the diffuser.

2. When re-installing the front plate, position the three

springs to the match the same rungs as on delivery.

Swegon reserves the right to alter speciﬁcations. 20130610 www.swegon.com

WISE

Figure 3. Lighting ﬁxtures or similar objects must not be installed

beneath the diffuser as this disrupts the presence detection and

room temperature measurement.

Maintenance

The exterior surface of the ADAPT air diffusers can be

cleaned whenever necessary using lukewarm water with

dishwashing detergent added.

The duct system is accessible through the air diffuser and

the commissioning box.

Commissioning

All the ADAPT Air diffusers are delivered preset into com-

missioning mode, which means that the air diffuser is set to

max. airﬂow by force control.

When the ADAPT air diffuser is in commissioning mode,

the light-emitting diode shines orange. The different LED

indications:

• Steady green LED: Normal operation, the air diffuser is

operating normally.

• Flashing green LED: The air diffuser has just been

powered on and calibration is in progress.

• Steady red LED: Function failure, see separate docu-

mentation in the TUNE Adapt manual.

• Steady orange LED: The commissioning mode, max.

airﬂow

• Flashing orange LED: Other commissioning modes and

all the forced control situations of the feedback control

system.

More information about the commissioning process itself

can be read in the Project Manual for the Wise system and

in the TUNE Adapt manual.

Swegon reserves the right to alter speciﬁcations. 20130610 www.swegon.com

WISE

Figure 4. Commissioning with TUNE Adapt.

24 V

Modbus

Electrical connections.

All the connections are wired to the CONNECT Adapt con-

nection box. From there, the Master air diffuser is connected

by means of the LINK Adapt (RJ45) cable included in the

delivery. The slave air diffusers, if required, are connected

by means of the same type of cable to their respective slave

contacts. If there are more than 2 slave air diffusers, a SPLIT

Link Adapt should be used for further connection to the last

slave air diffuser. See Figure 6. If SPLIT Link Adapt is used, the

maximum length of LINK Adapt from the connection box to

the last air diffuser is 15 meters. If ADAPT is to be connected

through Modbus communication, this should be done with

the LINK Modbus (RJ12) cable. The maximum length of

SPLIT Link Modbus is 10 meters from the connection box to

the last air diffuser. Use double CONNECT Adapts if longer

distances are required. All cables and contacts are different

so that they will not be confused or incorrectly connected.

Electrical data

ADAPT is supplied with power via the connection box. See

the wiring diagram in ﬁgure 6 or relevant diagram from the

Swegon Templates application, containing details for the

speciﬁc installation. It is important that cables with appro-

priate cross-sectional area, transformers of correct size and

power supply cables of correct length are selected. This

can for example be carried out with the dimensioning tool

“Cable and Transformer Design”, available for download

from www.swegon.com (the application is available in

english and swedish language versions).

Supply voltage 24 V AC ±10 %

Max. power consumption (controller only) 3 VA

Cable rating (controller only) 0,6 A

Ambient temperature 0 °C - +50 °C

Figure 5. Air diffuser connections.

1. Connection for LINK Adapt cable (RJ45)

2. Connection for the LINK Modbus cable (RJ12).

3. Direct 24 V connection if a connection box is not used and the

air diffuser will be completely “stand alone”.

Swegon reserves the right to alter speciﬁcations. 20130610 www.swegon.com

WISE

Master

Slave

Modbus

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

565

- + C

12 6

Figure 6. Connection of slave air diffusers and accessories. For

the ADAPT E, one slave air diffuser is normally connected to the

Connection box of the Master air diffuser.

1. ADAPT Master air diffuser (not shown in picture)

2. ADAPT E

3. CONNECT Adapt, wiring terminal for the Master air diffuser

4. 24 V AC Transformer

5. LINK Adapt, 5 m long (RJ45 cable)

6. LINK Modbus, 5 m long (RJ12 cable)

10. Connection to main control system (Modbus RTU)

12. SPLIT Modbus RJ12, max. stab length, 10 m

Other Swegon Fan manuals

Swegon

Swegon EAGLE Wall b Guide

Swegon

Swegon CASA R7H Smart Guide

Swegon

Swegon CASA R120 Instruction Manual

Swegon

Swegon ADAPT Sphere b Guide

Swegon

Swegon COMPACT Air User manual

Swegon

Swegon GOLD PX Series Troubleshooting guide

Swegon

Swegon ADAPT Parasol EXb Series Guide

Swegon

Swegon DOMO C Guide

Swegon

Swegon WISE Colibri Ceiling a User manual

Swegon

Swegon EXP Free b User manual

Swegon

Swegon CASA R120 Operator's manual

Swegon

Swegon WISE Paragon d User manual

Swegon

Swegon EAGLE Ceiling User manual

Swegon

Swegon KITE Ceiling User manual

Swegon

Swegon ADAPT Colibri Guide

Swegon

Swegon SILVER C User manual

Swegon

Swegon ADAPT Extract Guide

Swegon

Swegon WISE Parasol a User manual

Swegon

Swegon ADRIATIC VFc Series Guide

Swegon

Swegon ADAPT Parasol b 600 Guide

Swegon

Swegon CASA W100B Programming manual

Swegon

Swegon KDYa Series Guide

Swegon

Swegon WISE Kite Ceiling a User manual

Swegon

Swegon LPAa Guide

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual