Swegon ADAPT Sphere c User manual

ADAPTTM Sphere c

Installation – Commissioning – Maintenance 20130603 / Art. No. 1545216

Installation

1. The commissioning box can be suspended from a

ceiling and connected to a duct system. Use hanger

system (A) or (B), see ﬁgure 2.

2. The front plate of ADAPT Sphere can be dismantled by

pressing the ﬁxing pins of the bottom plate outward,

which will loosen it from the upper cone. The bottom

plate is secured to the upper cone by a safety cord.

3. Press the ADAPT Sphere air diffuser into the outlet of

the commissioning box. Make sure that the orientation

of the sensor module aligns with the extension of the

room, see ﬁgure 1. Then ﬁxate and secure the diffuser

with screws or pop rivets. Readjust the hanger rods of

the commissioning box if necessary, so that the air dif-

fuser is ﬁrmly positioned against the false ceiling.

4. Connect the air diffuser connector into the top of the dif-

fuser (C, ﬁgure 2) and attach the safety cord. Press together

the S-shaped hook to prevent it from coming loose.

5. Attach the diffuser section to the cone using the 3 pins.

6. The distance between the commissioning box and the

diffuser section can be extended to up to 200 mm. If a

greater distance is required, this is only possible if an order

is placed for a special version with extra long cables.

Figure 2. ADAPT Sphere, installation.

Figure 1. The orientation of the sensor module in a room or in

an ofﬁce module. The LED’s of the sensor should be aligned with

the extension of the room in a straight line, facing the short sides

of the room as shown by the arrow in the ﬁgure.

2Swegon reserves the right to alter speciﬁcations. 20130603 www.swegon.com

WISE

More information about the commissioning process itself

can be read in the Project Manual for the Wise system and

in the TUNE Adapt manual.

Maintenance

The exterior surface of the ADAPT air diffusers can be

cleaned whenever necessary using lukewarm water with

dishwashing detergent added.

The duct system is accessible through the air diffuser and

the commissioning box.

Commissioning

All the ADAPT Air diffusers are delivered preset into com-

missioning mode, which means that the air diffuser is set to

max. airﬂow by override control.

When the ADAPT air diffuser is in commissioning mode,

the light-emitting diode shines orange. The different LED

indications:

• Steady green LED: Normal operation, the air diffuser is

operating normally.

• Flashing green LED: The air diffuser has just been

powered on and calibration is in progress.

• Steady red LED: Function failure, see separate docu-

mentation in the TUNE Adapt manual.

• Steady orange LED: The commissioning mode, max.

airﬂow

• Flashing orange LED: Other commissioning modes

and all the override control situations of the feedback

control system.

Figure 3. Lighting ﬁxtures or similar objects must not be installed

beneath the diffuser as this disrupts the presence detection and

room temperature measurement.

Swegon reserves the right to alter speciﬁcations. 20130603 www.swegon.com

WISE

Electrical connections.

All the connections are wired to the CONNECT Adapt con-

nection box. From there, the Master air diffuser is connected

by means of the LINK Adapt (RJ45) cable included in the

delivery. The slave air diffusers, if required, are connected

by means of the same type of cable to their respective slave

contacts. If there are more than 2 slave air diffusers, a SPLIT

Link Adapt should be used for further connection to the last

slave air diffuser. See Figure 6. If SPLIT Link Adapt is used, the

maximum length of LINK Adapt from the connection box to

the last air diffuser is 15 meters. If ADAPT is to be connected

through Modbus communication, this should be done with

the LINK Modbus (RJ12) cable. The maximum length of

SPLIT Link Modbus is 10 meters from the connection box to

the last air diffuser. Use double CONNECT Adapts if longer

distances are required. All cables and contacts are different

so that they will not be confused or incorrectly connected.

Electrical data

ADAPT is supplied with power via the connection box. See

the wiring diagram in ﬁgure 6 or relevant diagram from the

Swegon Templates application, containing details for the

speciﬁc installation. It is important that cables with appro-

priate cross-sectional area, transformers of correct size and

power supply cables of correct length are selected. This

can for example be carried out with the dimensioning tool

“Cable and Transformer Design”, available for download

from www.swegon.com (the application is available in

english and swedish language versions).

Supply voltage 24 V AC ±10 %

Max. power consumption (controller only) 3 VA

Cable rating (controller only) 0,6 A

Ambient temperature 0 °C - +50 °C

Figure 5. Air diffuser connections.

1. Connection for LINK Adapt cable (RJ45)

2. Connection for the LINK Modbus cable (RJ12).

3. Direct 24 V connection if a connection box is not used and the

air diffuser will be completely “stand alone”.

Figure 4. Commissioning with TUNE Adapt.

24 V

Modbus

4Swegon reserves the right to alter speciﬁcations. 20130603 www.swegon.com

WISE

Figure 6. Wiring of Master/Slave air diffusers and accessories.

1. ADAPT Master air diffuser

2. ADAPT Slave air diffusers

3. CONNECT Adapt, connection box

4. 24 V AC Transformer

5. LINK Adapt (5 m long RJ45 cable)

6. LINK Modbus (5 m long RJ12 cable)

7a. TUNE Temp (1 VA)

7b. DETECT Quality (Room version with display - Q0: 1 VA.

Room version without display Q1 and duct version - Q2: 3 VA)

7c. DETECT RH, humidity sensor (1 VA)

8. ACTUATOR, radiator control (max 3 valves at 6 VA)

9. ADAPT Relay, relay for lighting

10. Connection to main control system (Modbus RTU)

11. SPLIT Link RJ45

12. SPLIT Modbus RJ12, max. stab length, 10 m.

*) Only one of the accessories in paragraph 7 can be connected at

any one time in a room installation.

Master

Slave

Modbus

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

- + C

A1 A2 1 3

12 22

12 6

OUT1

This manual suits for next models

Other Swegon Fan manuals

Swegon

Swegon ADAPT Parasol EXb Series Guide

Swegon

Swegon SWAN a Guide

Swegon

Swegon ADAPT Free Guide

Swegon

Swegon GOLD LP Troubleshooting guide

Swegon

Swegon ADAPT Free b Guide

Swegon

Swegon HAWK Ceiling a Guide

Swegon

Swegon GOLD SD 004/005 User manual

Swegon

Swegon SILVER C series User manual

Swegon

Swegon CASA R120 Instruction Manual

Swegon

Swegon PARAGON Wall VAV Guide

Swegon

Swegon CDHb Guide

Swegon

Swegon WISE Damper a User manual

Swegon

Swegon GOLD RX Series User manual

Swegon

Swegon PARASOL Zenith a Series User manual

Swegon

Swegon CASA R120 Programming manual

Swegon

Swegon PARAGON Wall c NC User manual

Swegon

Swegon CASA W3 Smart User manual

Swegon

Swegon PARASOL VAV Series Guide

Swegon

Swegon CASA R9H Smart Guide

Swegon

Swegon CASA W4 Smart User manual

Swegon

Swegon WISE Parasol EX User manual

Swegon

Swegon LOCKZONE Ceiling a Guide

Swegon

Swegon GOLD PX Instruction Manual

Swegon

Swegon COLIBRI Free b Guide

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual