Superior VRT4032ZMN User manual

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

This appliance may be installed in an aftermarket permanently located, manufactured (mobile) home, where not

prohibited by local codes. This appliance is only for use with the type of gas indicated on the rating plate. This

appliance is not convertible for use with other gases.

This is an unvented gas-ﬁred heater. It uses air (oxygen) from the room in which it is installed. Provisions

for adequate combustion and ventilation air must be provided. Refer to Air for Combustion and Ventilation

section on page 6 of this manual.

WARNING: If the information in these instructions is not followed exactly, a ﬁre or explosion may result

causing property damage, personal injury or loss of life.

—Do not store or use gasoline or other ﬂammable vapors and liquids in the vicinity of this or any other

appliance.

—WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ﬁre department.

—Installation and service must be performed by a qualiﬁed installer, service agency or the gas supplier.

Installation and Operation Instructions

Superior™ Radiant Faced Fireplace System with

Logs and Thermostat Blower

P/N 126868-01 Rev.A 02/2014 Models

VRT4032ZMN VRT4032ZMP VRT4036ZMN VRT4036ZMP

P126868-01

www.SuperiorFireplaces.US.com 126868-01A2

TABLE OF CONTENTS

Safety .................................................................. 2

Product Identication........................................... 4

Local Codes......................................................... 5

Unpacking............................................................ 5

Product Features................................................. 5

Air For Combustion and Ventilation..................... 6

Installation ........................................................... 8

Operation........................................................... 21

Inspecting Burners............................................. 23

Cleaning and Maintenance................................ 24

Troubleshooting................................................. 25

Wiring Diagram.................................................. 29

Specications .................................................... 29

Replacement Parts............................................ 29

Service Hints ..................................................... 29

Technical Service............................................... 29

Parts .................................................................. 30

Accessories ....................................................... 35

Warranty ............................................................ 36

WARNING: Improper instal-

lation, adjustment, alteration,

service, or maintenance can

cause injury or property damage.

Refer to this manual for correct

installation and operational

procedures. For assistance or

additional information consult

a qualified installer, service

agency, or the gas supplier.

WARNING: This is an un-

vented gas-red heater. It uses

air (oxygen) from the room in

which it is installed. Provisions

for adequate combustion and

ventilation air must be provided.

Refer to Air for Combustion and

Ventilation section on page 6 of

this manual.

This appliance may be installed

in an aftermarket,* permanently

located, manufactured (mobile)

home, where not prohibited by

local codes.

This appliance is only for use

with the type of gas indicated on

the rating plate. This appliance

is not convertible for use with

other gases.

* Aftermarket: Completion of sale, not for

purpose of resale, from the manufacturer

WARNING: This product con-

tains and/or generates chemicals

known to the state of California

to cause cancer or birth defects,

or other reproductive harm.

IMPORTANT: Read this owner’s

manual carefully and completely

before trying to assemble, operate,

or service this replace. Improper

use of this replace can cause

serious injury or death from burns,

re, explosion, electrical shock,

and carbon monoxide poisoning.

DANGER: Carbon monoxide

poisoning may lead to death!

Carbon Monoxide Poisoning: Early signs

of carbon monoxide poisoning resemble the

u, with headaches, dizziness, or nausea. If

you have these signs, the replace may not

be working properly. Get fresh air at once!

Have replace serviced. Some people are

more affected by carbon monoxide than oth-

ers. These include pregnant women, people

with heart or lung disease or anemia, those

under the inuence of alcohol, and those at

high altitudes.

Natural and Propane/LP Gas: Natural and

propane/LP gases are odorless. An odor-

making agent is added to these gases. The

odor helps you detect a gas leak. However,

the odor added to the gas can fade. Gas may

be present even though no odor exists.

Make certain you read and understand all

warnings. Keep this manual for reference. It

is your guide to safe and proper operation of

this replace.

www.SuperiorFireplaces.US.com

126868-01A 3

WARNING: Any change to

this heater or its controls can

be dangerous.

WARNING: Do not allow fans

to blow directly into the replace.

Avoid any drafts that alter burner

ame patterns. Ceiling fans can

create drafts that alter burner

ame patterns. Altered burner

patterns can cause sooting.

WARNING: Do not use a

blower insert, heat exchanger

insert, or other accessory not ap-

proved for use with this replace.

Due to high temperatures, the

appliance should be located out

of trafc and away from furniture

and draperies.

Do not place clothing or other

ammable material on or near

the appliance. Never place any

objects in the replace.

Fireplace front and screen be-

come very hot when running

fireplace. Keep children and

adults away from hot surfaces

to avoid burns or clothing igni-

tion. Fireplace will remain hot

for a time after shutdown. Allow

surfaces to cool before touching.

Carefully supervise young chil-

dren when they are in the room

with replace.

You must operate this replace

with the replace screen and

hood in place. Make sure re-

place screen is in place before

running replace.

SAFETY

Continued

Keep the appliance area clear

and free from combustible

materials, gasoline, and other

ammable vapors and liquids.

1. This appliance is only for use with type of

gas indicated on rating plate. This appli-

ance is not convertible for use with other

gases.

2. Do not place propane/LP supply tank(s)

inside any structure. Locate propane/

LP supply tank(s) outdoors (propane/LP

only).

3. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not

use any phone in your building

• immediately call your gas supplier from

a neighbor’s phone. Follow the gas sup-

plier’s instructions

• if you cannot reach your gas supplier,

call the re department

4. This replace shall not be installed in a

bedroom or bathroom.

5. Do not use this replace as a wood-burn-

ing replace. Use only the logs provided

with the replace.

6. Do not add extra logs or ornaments such

as pine cones, vermiculite, or rock wool.

Using these added items can cause soot-

ing. Do not add lava rock around base.

Rock and debris could fall into the control

area of replace.

7. This replace is designed to be smoke-

less. If logs ever appear to smoke, turn

off replace and call a qualied service

person.

Note: During initial operation, slight smok-

ing could occur due to log curing and

replace burning manufacturing residues.

8. To prevent the creation of soot, follow the

instructions in Cleaning and Maintenance,

page 23.

9. Before using furniture polish, wax, carpet

cleaner, or similar products, turn heater

off. If heated, the vapors from these prod-

ucts may create a white powder residue

within burner box or on adjacent walls or

furniture.

www.SuperiorFireplaces.US.com 126868-01A4

SAFETY

Continued

10. This replace needs fresh air ventilation to

run properly. This replace has an Oxygen

Depletion Sensing (ODS) safety shutoff

system. The ODS shuts down the re-

place if not enough fresh air is available.

See Air for Combustion and Ventilation,

page 6. If replace keeps shutting off, see

Troubleshooting, page 24.

11. Do not run replace

• where ammable liquids or vapors are

used or stored.

• under dusty conditions.

12. Do not use this replace to cook food or

burn paper or other objects.

13. Do not use replace if any part has been

under water. Immediately call a qualied

service technician to inspect the room

replace and to replace any part of the

control system and any gas control which

has been under water.

Figure 1 - Log Base Assembly

Top Outer Casing

Figure 2 - Fireplace

Log Set

Base

Assembly

Front

Burner

Top panel

Assembly

Fireplace

Hood

Bottom Panel

Assembly

Screen

Assembly

Magnet

14. Turn off and unplug fireplace and let

cool before servicing. Only a qualied

service person should service and repair

replace.

15. Operating replace above elevations of

4,500 feet could cause pilot outage.

16. Do not operate fireplace if any log is

broken. Do not operate replace if a log

is chipped (dime-sized or larger).

17. To prevent performance problems, do not

use propane/LP fuel tank of less than 100

lbs. capacity (propane/LP only).

18. Provide adequate clearances around air

openings.

19. The screen or any other part removed

for servicing must be replaced prior to

operating this heater.

PRODUCT

IDENTIFICATION Left Side

Right

Side

Front

www.SuperiorFireplaces.US.com

126868-01A 5

LOCAL CODES

UNPACKING

Install and use replace with care. Follow all

local codes. In the absence of local codes,

use the latest edition of The National Fuel

Gas Code ANSI Z223.1/NFPA 54*.

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

Note: Where listed vented decorative logs

are required, thermostat operation is not

permitted.

State of Massachusetts: The installation

must be made by a licensed plumber or

gas tter in the Commonwealth of Mas-

sachusetts.

Sellers of unvented propane or natural

gas-red supplemental room heaters shall

provide to each purchaser a copy of 527

CMR 30 upon sale of the unit.

Vent-free gas products are prohibited for

bedroom and bathroom installation in the

Commonwealth of Massachusetts.

CAUTION: Do not remove the

data plates attached to the heater

base assembly. The data plates

contain important warranty and

safety information.

1. With utility knife, cut the carton all the way

around above the staples on the bottom

tray. Lift the carton off the heater. Remove

packing.

Note: The hood is located in the packing

on the right hand side of the heater front.

Lift the heater off the bottom tray.

2. Locate two screws above top corners of

the replace screen. Remove and discard

these screws. Push the bottom corners of

the screen in and release. The screen will

pop out at the bottom. Grasp the bottom

of the screen, lift the screen up and pull

out to remove.

3. Remove protective packaging applied to

logs, log base assembly, and replace.

4. Remove fireplace hood from carton

inserts.

5. Check all items for any shipping damage.

If damaged, promptly inform dealer where

you bought replace.

PRODUCT FEATURES

OPERATION

This vent-free replace is clean burning. It

requires no outside venting. There is no heat

loss out a vent or up a chimney. Heat is gen-

erated by both realistic ames and glowing

embers. When used without the blower, the

replace requires no electricity making it ideal

for emergency backup heat.

SAFETY DEVICE

This replace has a pilot with an Oxygen

Depletion Sensing (ODS) safety shutoff

system. The ODS/pilot is a required feature

for vent-free room heaters. The ODS/pilot

system shuts off the replace if there is not

enough fresh air.

PIEZO IGNITION SYSTEM

This replace has a piezo ignitor. This sys-

tem requires no matches, batteries, or other

sources to light replace.

OPTIONAL REMOTE CONTROL

ACCESSORY

There are ve optional remote controls (not

included) that can be purchased separately for

this log heater:

• wall switch

• wall thermostat

• hand-held ON/OFF remote

• hand-held thermostat remote

• TSRC hand-held remote

See Accessories, page 35.

BLOWER ASSEMBLY ACCESSORY

This replace includes a blower assembly. The

blower operates thermostatically and features

a variable speed control. The blower circulates

www.SuperiorFireplaces.US.com 126868-01A6

may provide enough fresh air for combustion

and ventilation. However, in buildings of un-

usually tight construction, you must provide

additional fresh air.

Unusually tight construction is dened as

construction where:

a. walls and ceilings exposed to the out-

side atmosphere have a continuous

water vapor retarder with a rating of one

perm (6 x 10-11 kg per pa-sec-m2) or less

with openings gasketed or sealed and

b. weather stripping has been added on

openable windows and doors and

c. caulking or sealants are applied to

areas such as joints around window

and door frames, between sole plates

and oors, between wall-ceiling joints,

between wall panels, at penetrations for

plumbing, electrical, and gas lines, and

at other openings.

If your home meets all of the three criteria

above, you must provide additional fresh air.

See Ventilation Air From Outdoors, page 8.

If your home does not meet all of the three

criteria above, proceed to Determining

Fresh-Air Flow For Heater Location.

Conned and Unconned Space

The National Fuel Gas Code, ANSI Z223.1/

NFPA 54 denes a conned space as a space

whose volume is less than 50 cubic feet per

1,000 Btu per hour (4.8 m3 per kw) of the ag-

gregate input rating of all appliances installed in

that space and an unconned space as a space

whose volume is not less than 50 cubic feet per

1,000 Btu per hour (4.8 m3 per kw) of the ag-

gregate input rating of all appliances installed in

that space. Rooms communicating directly with

the space in which the appliances are installed*,

through openings not furnished with doors, are

considered a part of the unconned space.

* Adjoining rooms are communicating only if

there are doorless passageways or ventilation

grills between them.

DETERMINING FRESH-AIR FLOW

FOR FIREPLACE LOCATION

Determining if You Have a Conned or

Unconned Space

Use this work sheet to determine if you have

a conned or unconned space.

Space: Includes the room in which you will install

replace plus any adjoining rooms with door-

less passageways or ventilation grills between

heated air from the replace into the room.

AIR FOR COMBUSTION

AND VENTILATION

WARNING: This heater shall

not be installed in a room or

space unless the required vol-

ume of indoor combustion air

is provided by the method de-

scribed in the National Fuel Gas

Code, ANSI Z223.1/NFPA 54, the

International Fuel Gas Code, or

applicable local codes. Read the

following instructions to insure

proper fresh air for this and

other fuel-burning appliances

in your home.

Today’s homes are built more energy efcient

than ever. New materials, increased insulation,

and new construction methods help reduce

heat loss in homes. Home owners weather

strip and caulk around windows and doors to

keep the cold air out and the warm air in. Dur-

ing heating months, home owners want their

homes as airtight as possible.

While it is good to make your home energy

efcient, your home needs to breathe. Fresh

air must enter your home. All fuel-burning ap-

pliances need fresh air for proper combustion

and ventilation.

Exhaust fans, replaces, clothes dryers, and

fuel burning appliances draw air from the house

to operate. You must provide adequate fresh

air for these appliances. This will insure proper

venting of vented fuel-burning appliances.

PROVIDING ADEQUATE

VENTILATION

The following are excerpts from National Fuel

Gas Code, ANSI Z223.1/NFPA 54, Air for

Combustion and Ventilation.

All spaces in homes fall into one of the three

following ventilation classications:

1. Unusually Tight Construction

2. Unconned Space

3. Conned Space

The information on pages 6 through 8 will help

you classify your space and provide adequate

ventilation.

Unusually Tight Construction

The air that leaks around doors and windows

www.SuperiorFireplaces.US.com

126868-01A 7

the rooms.

1. Determine the volume of the space (length

x width x height).

Length x Width x Height =__________cu. ft.

(volume of space)

Example: Space size 20 ft. (length) x 16 ft.

(width) x 8 ft. (ceiling height) = 2,560 cu. ft.

(volume of space)

If additional ventilation to adjoining room

is supplied with grills or openings, add the

volume of these rooms to the total volume

of the space.

2. Multiply the space volume by 20 to determine

the maximum Btu/Hr the space can support.

________ (volume of space) x 20 = (Maxi-

mum Btu/Hr the space can support)

Example: 2,560 cu. ft. (volume of space) x

20 = 51,200 (maximum Btu/Hr the space can

support)

3. Add the Btu/Hr of all fuel burning appliances

in the space.

Vent-free replace _________ Btu/Hr

Gas water heater* _________ Btu/Hr

Gas furnace _________ Btu/Hr

Vented gas heater _________ Btu/Hr

Gas replace logs _________ Btu/Hr

Other gas appliances* +________ Btu/Hr

Total = ________ Btu/Hr

* Do not include direct-vent gas appliances.

Direct-vent draws combustion air from the

outdoors and vents to the outdoors.

Example:

Gas water heater _____________ Btu/Hr

Vent-free replace + ___________ Btu/Hr

Total =____________ Btu/Hr

4. Compare the maximum Btu/Hr the space

can support with the actual amount of Btu/

Hr used.

_______ Btu/Hr (maximum the space can

support)

_______ Btu/Hr (actual amount of Btu/Hr

used)

Example: 51,200 Btu/Hr (maximum the

space can support)

73,000 Btu/Hr (actual amount of

Btu/Hr used)

The space in the example is a conned space

because the actual Btu/Hr used is more than the

maximum Btu/Hr the space can support. You

must provide additional fresh air. Your options

are as follows:

A. Rework worksheet, adding the space of an

adjoining room. If the extra space provides an

unconned space, remove door to adjoining

room or add ventilation grills between rooms.

See Ventilation Air From Inside Building.

AIR FOR COMBUSTION AND VENTILATION

Continued

40,000

33,000

73,000

Figure 3 - Ventilation Air from Inside

Building

Remove

Door into

Adjoining

Room,

Option

Ventilation Grills

Into Adjoining Room,

Option 2

Ventilation

Grills Into

Adjoining

Room,

Option 1

12"

B. Vent room directly to the outdoors. See

Ventilation Air From Outdoors page 8.

C. Install a lower Btu/Hr replace, if lower Btu/

Hr size makes room unconned.

If the actual Btu/Hr used is less than the maxi-

mum Btu/Hr the space can support, the space is

an unconned space. You will need no additional

fresh air ventilation.

WARNING: If the area in which

the heater may be operated does

not meet the required volume for

indoor combustion air, combus-

tion and ventilation air shall be

provided by one of the methods

described in the National Fuel

Gas Code, ANSI Z223.1/NFPA

54, the International Fuel Gas

Code, or applicable local codes.

VENTILATION AIR

Ventilation Air From Inside Building

This fresh air would come from an adjoining

unconned space. When ventilating to an

adjoining unconned space, you must provide

two permanent openings: one within 12" of the

ceiling and one within 12" of the oor on the

wall connecting the two spaces (see options

1 and 2, Figure 3). You can also remove door

into adjoining room (see option 3, Figure 3).

www.SuperiorFireplaces.US.com 126868-01A8

INSTALLATION

CAUTION: This replace cre-

ates warm air currents. These

currents move heat to wall sur-

faces next to replace. Installing

replace next to vinyl or cloth

wall coverings or operating

heater where impurities (such

as, but not limited, to tobacco

smoke, aromatic candles, clean-

ing uids, oil or kerosene lamps,

etc.) in the air exist, may discolor

walls or cause odors.

Note: Your replace is designed to be used in

zero clearance installations. Wall or framing

material can be placed directly against any

exterior surface on the rear, sides, or top of

your replace, except where standoff spac-

ers are integrally attached. Where standoff

spacers are attached to your fireplace,

combustible material (studs and wall board)

may be place on top and above the top of

the standoffs.

Use the dimensions shown for rough openings

to create the easiest installation. See Built-In

Fireplace Installation, page 11.

IMPORTANT: Vent-free heaters add moisture

to the air. Although this is benecial, installing

replace in rooms without enough ventilation

air may cause mildew to form from too much

moisture. See Air for Combustion and Ventila-

tion, page 6.

IMPORTANT: Make sure the replace is level. If

replace is not level, log set will not work properly.

Figure 4 - Ventilation Air from Outdoors

Outlet

Air

Ventilated

Attic

Outlet

Inlet

Air

Inlet Air Ventilated

Crawl Space

Crawl

Space

To Attic

Follow the National Fuel Gas Code, ANSI

Z223.1/NFPA 54, Air for Combustion and

Ventilation for required size of ventilation

grills or ducts.

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation

grills or ducts. You must provide two perma-

nent openings: one within 12" of the ceiling

and one within 12" of the oor. Connect these

items directly to the outdoors or spaces open

to the outdoors. These spaces include attics

and crawl spaces. Follow the National Fuel

Gas Code, ANSI Z223.1/NFPA 54, Air for

Combustion and Ventilation for required size

of ventilation grills or ducts.

NOTICE: This heater is intended

for use as supplemental heat.

Use this heater along with your

primary heating system. Do not

install this heater as your pri-

mary heat source. If you have a

central heating system, you may

run system’s circulating blower

while using heater. This will help

circulate the heat throughout the

house. In the event of a power

outage, you can use this heater

as your primary heat source.

WARNING: A qualied ser-

vice person must install re-

place. Follow all local codes.

WARNING: Never install the

replace

• in a bedroom or bathroom

• in a recreational vehicle

• where curtains, furniture,

clothing, or other ammable

objects are less than 36" from

the front and 42" from the top

of replace. For side clear-

ances see Figure 8, page 10

• in high trafc areas

• in windy or drafty areas

AIR FOR COMBUSTION AND VENTILATION

Continued

www.SuperiorFireplaces.US.com

126868-01A 9

Figure 5 - Installing Hood

Screw

Hood

Rail

INSTALLATION

Continued

Assembled

Trim

Figure 7 - Attaching Perimeter Trim to

Fireplace

Trim

Hanging

Screws

Hanging

Notches

on Trim

Figure 6 - Assembling Perimeter Trim

Side Trim

Slot

Mitered

Edge

Slot

Shim

Set Screws

Adjusting

Plate Top

Trim

Mitered

Edge

ASSEMBLING AND ATTACHING

OPTIONAL PERIMETER TRIM

IMPORTANT: If you are recessing the rebox

in a wall, do not attach trim at this time. See

Built-In Fireplace Installation, page 11.

Note: These instructions show assembling

and attaching trim to replace.

1. Remove packaging from three pieces

of trim.

2. Locate four screws, two adjusting plates

with set screws, and two shims in the

hardware packet.

CHECK GAS TYPE

Use the correct gas type (natural or propane/

LP) for your replace. If your gas supply is not

correct, do not install replace. Call dealer

where you bought replace for proper type

replace.

WARNING: This appliance is

equipped for natural or propane/

LP gas but not both. Gas type is

indicated on rating plate. Field

conversion is not permitted.

ELECTRICAL HOOKUP

This replace includes a blower which must

be connected to either a wall receptacle or

the electrical receptacle that is included within

the replace. If the receptacle included with

the replace is to be used, it must be wired

to a 120 volt supply by a certied electrician.

INSTALLING HOOD

Install hood to rail already installed in replace

as shown in Figure 5. Use 3 Phillips screws

provided.

3. Align shim under adjusting plate as shown

in Figure 6.

4. Slide one end of adjusting plate/shim

in slot on mitered edge of top trim (see

Figure 6).

5. Slide other end of adjusting plate/shim

in slot on mitered edge of side trim (see

Figure 6).

6. While firmly holding edges of trim to-

gether, tighten both set screws on the

adjusting plate with slotted screwdriver.

7. Repeat steps 1 through 6 for other side.

8. Tighten trim hanging screws (#10 x 6.25

shoulder) into holes in cabinets. Place

the assembled trim onto replace cabinet.

Align hanging notches on trim with hang-

ing screws on side of replace (see Figure

7). Push trim rmly into place, sliding

hanging notches over hanging screws.

www.SuperiorFireplaces.US.com 126868-01A10

INSTALLATION

Continued

2. Install a properly grounded, 120 volt three-

prong electrical outlet at replace location

if an outlet is not there. If possible, locate

outlet so cabinet mantel will cover it when

installed (see Figure 9).

3. Install gas piping to replace location. This

installation includes an approved exible

gas line (if allowed by local codes) after

the equipment shutoff valve. The exible

gas line must be the last item installed on

the gas piping. See Installing Gas Piping

to Fireplace Location, page 13.

4. Place hearth base accessory against wall at

installation location. Cut an access hole in

hearth top to run exible gas line to replace

(see Figure 9). Make sure to locate access

hole so cabinet mantel will cover it when

installed.

Note: You can secure base to oor using

wood screws. Countersink screw heads

and putty over.

5. Route exible gas line through access

hole in hearth base.

6. Center cabinet mantel on hearth base (see

Figure 10, page 11). Make sure mantel is

ush against wall.

7. Place cardboard or other protective mate-

rial on top of hearth base. Carefully set

replace on protective material, with back

of replace inside mantel opening.

8. Attach exible gas line from replace gas

regulator to gas supply. See Connecting

Fireplace to Gas Supply,page 14.

9. Route blower electrical cord through ac-

cess holes in either side of replace.

CONVENTIONAL FIREPLACE

INSTALLATION

Conventional installation of this fireplace

involves installing replace along with the

corner, face, or cabinet mantel with hearth

base accessories against a wall in your home.

Follow the instructions in this section to install

the replace in this manner.

1. Assemble cabinet mantel, hearth base,

and trim accessories. Assembly instruc-

tions are included with each accessory. Figure 9 - Placing Hearth Base

Accessory Against Wall

Electrical Outlet

Hearth Base

Rigid Pipe and Gas

Shutoff Valve

Gas Line

Access Hole

INSTALLATION CLEARANCES

WARNING: Maintain the

minimum clearances. If you can,

provide greater clearances from

oor, ceiling, and adjoining wall.

Carefully follow the instructions below. This

will ensure safe installation.

Minimum Clearances For Side Combustible

Material, Side Wall, and Ceiling

A. Clearances from the side of the replace

cabinet to any combustible material and

wall should follow diagram in Figure 8.

Example: The face of a mantel, bookshelf,

etc. is made of combustible material and

protrudes 3 1/2" from the wall. This com-

bustible material must be 4" from the side

of the replace opening (see Figure 8).

B. Clearances from top of replace opening

to ceiling should not be less than 42".

MINIMUM CLEARANCE TO

COMBUSTIBLE MATERIALS

Top 0", Left and Right Sides 16",

Bottom and Rear 0", Front 36"

*Minimum 16" from Side Wall

Figure 8 - Minimum Clearance for

Combustible to Wall

Example

This manual suits for next models

Table of contents

Other Superior Indoor Fireplace manuals

Superior

Superior DRT3535 Series User manual

Superior

Superior BRT4036TMN User manual

Superior

Superior CST38MH User manual

Superior

Superior STANDARD Series User manual

Superior

Superior DRL3042TEN User manual

Superior

Superior BRT4036TEN User manual

Superior

Superior WCT4820WS User manual

Superior

Superior UVFCE-40 User manual

Superior

Superior WRT40CRWSI User manual

Superior

Superior WRT3920WS User manual

Superior

Superior HC-3320A User manual

Superior

Superior DRT4040DMN Owner's manual

Superior

Superior SDVPF-N-B User manual

Superior

Superior BRT40STTMN User manual

Superior

Superior VRE4536WS User manual

Superior

Superior WRT6050 Owner's manual

Superior

Superior DRT3033 User manual

Superior

Superior SLDVT-40NM User manual

Superior

Superior HC-3320 User manual

Superior

Superior WRT2042WS User manual

Superior

Superior SLDVT Series User manual

Superior

Superior B-40RMN User manual

Superior

Superior SLDVT-35 Series User manual

Superior

Superior VRE4336ZEN User manual

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual

Miles Industries

Miles Industries Vogue 1300IRN Installation & operating instructions