Sungrow SG30CX User manual
TD_20210219_SG30-50-110CX Commissioning Guide_V1.1 Page 1 of 21
© SUNGROW AUSTRALIA GROUP PTY LTD All rights reserved.
As we continuously improving our products, changes to this document may occur without notice.
SG30/50/110CX Inverters Commissioning Quick
Guide (with Logger1000 and EyeM4)
Disclaimer
The material in this document has been prepared by Sungrow Australia Group Pty. Ltd. ABN 76 168
258 679 and is intended as a guideline to assist solar installers for troubleshooting. It is not a statement
or advice on any of the Electrical or Solar Industry standards or guidelines. Please observe all OH&S
regulations when working on Sungrow equipment.
Version
Revision History
Created by
Date
1.0
First version
AU Service Team
24th Dec 2020
1.1
Issued for Approval
AU Service Team
19th Feb 2021
This document only applies to Sungrow Power three-phase inverters (including
SG30CX, SG50CX and SG110CX) with Logger1000 or EyeM4. The information in this
document may contain predictive statements including, without limitation, statements
regarding the future financial and operating results, future product portfolio, new
technology, etc. There are several factors that could cause actual results and
developments to differ materially from those expressed or implied in the predictive
statements. Therefore, such information is provided for reference purpose only and
constitutes neither an offer nor an acceptance. Sungrow Power may change the
information at any time without notice.
TD_20210219_SG30-50-110CX Commissioning Guide_V1.1 Page 2 of 21
© SUNGROW AUSTRALIA GROUP PTY LTD All rights reserved.
As we continuously improving our products, changes to this document may occur without notice.
Contents
1Introduction ......................................................................................................... 3
2RS485 Connections............................................................................................ 5
2.1 Inverter Connection (Daisy Chain)................................................................ 5
2.2 Energy Meter Connection ............................................................................. 6
2.3 Connection to Logger1000 ............................................................................... 8
2.4 Connection via EyeM4...................................................................................... 9
3Web Portal Setup...............................................................................................11
3.1 Access Web Portal.......................................................................................11
3.2 Set local time................................................................................................12
3.3 Scan for Inverters.........................................................................................13
3.4 Add Energy Meter........................................................................................14
3.5 Enable Remote Control................................................................................16
3.6 Internet Connection......................................................................................17
3.6.1 Connect via Ethernet Cable (Logger1000 only) ........................................17
3.6.2 Connect via WiFi (Logger1000 and EyeM4C)...........................................17
3.6.3 Connect via 4G (EyeM4A Only)................................................................18
3.7 Add CT Transformation Ratio.......................................................................19
3.8 Setup Export Control if required...................................................................19
4Create Plant on iSolarCloud...............................................................................20
5Updating the Logger1000/EyeM4.......................................................................21
TD_20210219_SG30-50-110CX Commissioning Guide_V1.1 Page 3 of 21
© SUNGROW AUSTRALIA GROUP PTY LTD All rights reserved.
As we continuously improving our products, changes to this document may occur without notice.
1 Introduction
This quick guide is showing how to commission the SG30/50/110CX inverters and it
is to be read in conjunction with the Sungrow’s User Manuals.
Where more than one inverter, or an energy meter installed, the commissioning and
iSolarCloud connection is done via a Logger1000(Up to 30 devices) and EyeM4(Up to
10 devices).
For export control and load consumption, an energy meter (DTSD1352-C/1(6)A with
external CT) needed to be connected.
All of the components are connected via daisy-chain as per standard RS485 topology.
Logger 1000
RS485 A
RS485 B
RS485 A
RS485 B
3-Phase meter
Inverter 1
Inverter n
TD_20210219_SG30-50-110CX Commissioning Guide_V1.1 Page 4 of 21
© SUNGROW AUSTRALIA GROUP PTY LTD All rights reserved.
As we continuously improving our products, changes to this document may occur without notice.
Please use the following checklist for quick commissioning:
Procedures
Yes/No
RS485
connection
RS485 communication cables installed correctly between
inverters/ inverters to Logger1000/ meter to the logger1000
or the inverter has EyeM4 by terminal blocks?
RS485 communication cables installed correctly between
energy meter DTSD1352-C/1(6)A to Logger1000/ to the
inverter has the EyeM4 by terminal blocks?
Logger1000/
EyeM4 web
portal setup
Logger1000/ EyeM4 Setup via WLAN (11.11.11.1;
password: pw1111)
Set the local time
Auto search inverters
Add the energy meter and adjust CT Transformation Ratio
Set up export control if required
Remote
maintenance
Connect to internet via Ethernet Cable/ WiFi/ 4G
Enable International Server
Update iSolarCloud serve domain
Check Port Parameter for IP address
Setup Online
Monitoring
Create a solar plant via iSolarCloud APP via an installer
account
TD_20210219_SG30-50-110CX Commissioning Guide_V1.1 Page 5 of 21
© SUNGROW AUSTRALIA GROUP PTY LTD All rights reserved.
As we continuously improving our products, changes to this document may occur without notice.
2 RS485 Connections
2.1 Inverter Connection (Daisy Chain)
Recommend that RS485 can be connected by terminal blocks.
Please note SG15/20KTL-MT inverters connection is different as SG30/50/110CX inverters.
Optional: Ensure the termination resistors (120 Ohm) are enabled ON (SW1) at each
end of the RS485 in the inverter line (only the first and the last inverter) when more
than 15 inverters are connected.
TD_20210219_SG30-50-110CX Commissioning Guide_V1.1 Page 6 of 21
© SUNGROW AUSTRALIA GROUP PTY LTD All rights reserved.
As we continuously improving our products, changes to this document may occur without notice.
2.2 Energy Meter Connection
The site electrician will need to calculate the CT ratio required as per the installation.
Default Modbus address is 1 and the secondary current of CT should be 5A. Please
refer Meter Selection Guide for reference.
The corresponding pinouts to RJ45 are Pin 3 (White-green) to RS485- B and Pin 6
(Green) to RS485+ A:
DTSD1352 energy meter connection:
•Terminal 21 = RS485+ A (Green)
•Terminal 22 = RS485- B (White/Green)
TD_20210219_SG30-50-110CX Commissioning Guide_V1.1 Page 7 of 21
© SUNGROW AUSTRALIA GROUP PTY LTD All rights reserved.
As we continuously improving our products, changes to this document may occur without notice.
DTSU666 energy meter connection:
•Terminal 24 = RS485+ A (Green)
•Terminal 25 = RS485- B (White/Green)
Logger1000 connection: Connect to Logger1000 via the RS485 cable from the
energy meter on RS485 port A2 and B2 if it has not been used.
EyeM4 connection: Connect the energy meter RS485 to A2/B2 (RS485-2 Interface)
terminals in the inverter that has the EyeM4 dongle.
Note: the Logger1000 and EyeM4 must be updated to the latest firmware to support
the DTSU666 energy meter. To upgrade the Logger1000/ EyeM4, refer to th Part 5 of
this document.
TD_20210219_SG30-50-110CX Commissioning Guide_V1.1 Page 8 of 21
© SUNGROW AUSTRALIA GROUP PTY LTD All rights reserved.
As we continuously improving our products, changes to this document may occur without notice.
2.3 Connection to Logger1000
Connect the RS485 comms from the inverter(s) via A1/B1 and the energy meter via
A2/B2 (can be connect to A3/B3 if A2/B2 is occupied by inverters) to the Logger1000
as an example.
On the logger1000 side, A1 and B1 are terminals to connect with the inverter which
display as COM1 on the Logger1000 web portal; A2 and B2 are the terminals to
connect with the energy meter, they are shown as COM2on the portal.
TD_20210219_SG30-50-110CX Commissioning Guide_V1.1 Page 9 of 21
© SUNGROW AUSTRALIA GROUP PTY LTD All rights reserved.
As we continuously improving our products, changes to this document may occur without notice.
2.4 Connection via EyeM4
Connect the energy meter RS485 to A2/B2 (RS485-2 Interface) terminals in the
inverter that has the EyeM4 dongle. (Communication PCB varies between inverter
models –ensure to use A2/B2).
Figure 1.4.1 RS485 connections in the inverter (SG30/50CX and SG110CX)
Important: Enable RS485 Port for Inverter via iSolarCloud App
Access the iSolarCloud App via Bluetooth, once clicking Bluetooth, you will be
prompted to select the Bluetooth device (Inverter SN). Click on the SN you wish to
connect to and then login to the inverter. Please put in “admin” as the account and the
password (pw8888).
Click "More" > "Settings" > “Operation Parameters” > “Other Parameters” > Enable”
transparent transmission via standby RS485 port.
TD_20210219_SG30-50-110CX Commissioning Guide_V1.1 Page 10 of 21
© SUNGROW AUSTRALIA GROUP PTY LTD All rights reserved.
As we continuously improving our products, changes to this document may occur without notice.
Other manuals for SG30CX
5
This manual suits for next models
2
Table of contents
Other Sungrow Inverter manuals
Sungrow
Sungrow PowCube 4.8 Installation guide
Sungrow
Sungrow SG250HX User manual
Sungrow
Sungrow SG4950HV-MV User guide
Sungrow
Sungrow SG1100UD Series Instruction Manual
Sungrow
Sungrow SH3K6-30 User manual
Sungrow
Sungrow SG2K-S User manual
Sungrow
Sungrow SG250HX User manual
Sungrow
Sungrow SH6.0RT Installation guide
Sungrow
Sungrow SG1250UD User manual
Sungrow
Sungrow SG125HX User manual
Sungrow
Sungrow SG5.0RT User manual
Sungrow
Sungrow PowerStack-ST535kWh-250kW-2h User guide
Sungrow
Sungrow SG125HV User manual
Sungrow
Sungrow SG30 33 40 50CX User manual
Sungrow
Sungrow SH8.0RS User manual
Sungrow
Sungrow SG2K-S User manual
Sungrow
Sungrow SG125HX User manual
Sungrow
Sungrow SH5K Owner's manual
Sungrow
Sungrow SG2500HV-30 User guide
Sungrow
Sungrow SH5K-20 Owner's manual
Popular Inverter manuals by other brands
Astrel Group
Astrel Group Power Reducer Installation and instruction manual
MULTIQUIP
MULTIQUIP GDP-5H Operation and parts manual
GoWISE
GoWISE PS1007 user manual
Promate
Promate PM13500D ES Operator's manual
Mastervolt
Mastervolt WHISPER 3.5M3000 RPM user manual
Mitsubishi Electric
Mitsubishi Electric FR-A7AZ instruction manual