Storage Canopy C3340 User manual

SHELTER

ASSEMBLY MANUAL

Model # C3340 Back wall & frame of

Container Shelter

C3340 Back wall & frame

SPECIFICATION

Width:33ft Length:40ft Height:15ft

IMPORTANT ----- READ MANUAL FIRST

Improper site preparation, Assembly and Maintenance may invalidate warranty and cause unnecessary and

costly mistake. If you have any questions contact your local dealer.

For User Friendly assembly we have identified each individual component with the part code as indicated in

the parts list. Please refer to the part code numbers and drawing to ensure problem free assembly.

It’s necessary to tighten the roof fabric enough to avoid “hammocks” on the roof and also re-tighten once or

twice again after a few months of use. This is important when assembly in cold weather (autumn and winter)

because the fabric is stiff then and when we got the sun and warm weather afterwards it will make the fabric

“slack” again and need to be re-tighten before next winter.

It’s the owners responsibility to take of snow immediately if not slide off by itself.

READ ALL INSTRUCTIONS BEFORE ASSEMBLY

Keep work area clean. Cluttered areas invite injuries. Do not set up near snow drifts, in slippery places, in

high winds, or wet location.

Keep children away. All children should be kept away from the work area.

Don’t over reach. Keep proper footing and balance at all times.

Do not assemble in under the influence of alcohol or drugs. Read warning labels on prescriptions to

determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not

assemble.

Be aware of possible windy conditions; fasten the bases in concrete if these conditions are likely to occur.

Remove the cover during hurricane.

Be careful with power and heat sources. Do not keep heat sources near the tarpaulin. Do not expose to

open flame.

Be aware of personal safety during assembly and use. Be carful not to pinch fingers with clips and tubes

when assembling: when using makes sure there is adequate ventilation for exhaust and other dangerous

fumes.

Parts List

Part Code

Description

Qty

Base plates for winch door

Eccentric base plates

Standing leg at left

Standing leg at right

Side leg on the top for front and back endwall

Lower standing leg at left

Lower standing leg at right

Upper standing leg for winch door

Door beam

1 Group

Door boom

Horizontal tube for front door on the bottom

10A

Horizontal tube for front door on the top

Square tube for winch door

Mechanical wheel with wire rope

Bottom tension tube for front endwall

Door vertical tube

9 Groups

Clips φ60

15A

Welded iron plates for the side legs

15B

Single hole angle iron

Stake peg

Door splint

Bolts M10*30

Bolts M10*90

Bolts M10*60

Carriage Bolts M10*90

Carriage Bolts M12*100

Plastic Plug

Rope for pull door

Front cover

Added legs

Added door frame

SPECIFICATION

Width: 10m Length: 12m Height: 3.6m

IMPORTANT----- READ MANUAL FIRST

Improper site preparation, Assembly and Maintenance may invalidate warranty and cause

unnecessary and costly mistake. If you have any questions contact your local dealer.

For User Friendly assembly we have identified each individual component with the part code as

indicated in the parts list. Please refer to the part code numbers and drawing to ensure problem

free assembly.

It’s necessary to tighten the roof fabric enough to avoid “hammocks” on the roof and also

re-tighten once or twice again after a few months of use. This is important when assembly in cold

weather (autumn and winter) because the fabric is stiff then and when we got the sun and warm

weather afterwards it will make the fabric “slack” again and need to be re-tighten before next

winter.

It’s the owners responsibility to take of snow immediately if not slide off by itself.

READ ALL INSTRUCTIONS BEFORE ASSEMBLY

1. Keep work area clean. Cluttered areas invite injuries. Do not set up near snow drifts, in

slippery places, in high winds, or wet location.

2. Keep children away.All children should be kept away from the work area.

3.Don’t over reach. Keep proper footing and balance at all times.

4. Do not assemble in under the influence of alcohol or drugs. Read warning labels on

prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If

there is any doubt, do not assemble.

5. Be aware of possible windy conditions; fasten the bases in concrete if these conditions are

likely to occur. Remove the cover during hurricane.

6. Be careful with power and heat sources. Do not keep heat sources near the tarpaulin. Do not

expose to open flame.

7. Be aware of personal safety during assembly and use. Be carful not to pinch fingers with clips

and tubes when assembling: when using makes sure there is adequate ventilation for exhaust and

other dangerous fumes.

EQUIPEMNT AND TOOLS FOR INSTALIATION

1. Measuring tape

2. String for alignment

3. Step ladder

4. Welder

5. Sledge hammer

6. Wrench

7. Scissors

INSTALLATION PROCESS

A—FRAME INSTALLATION

Please refer to the diagram (Figure 1) to install the base plate. UNIT: mm

Figure 1

There are four base plate comes with the back endwall. Each of them should be placed in the

right position(especially the two base plate close to the containers.)

Figure 2

C--INSTRUCTION FOR COVER ATTACHED

Assembly the end cover first.

NOTE: DO NOT install the cover onto the frame of your building in high wind conditions. A

slight breeze is the most advantageous for cover installation. To take advantage of the breeze,

pull the cover up over the arches with the breeze blowing in the cover like a sail filled with air.

Figure 3

The process is quite easy. But some tightening adjustments will be necessary to produce a flat. Please adjust

the cover timely.

Table of contents

Other Storage Canopy Shelter manuals

Storage Canopy

Storage Canopy C4060DTR User manual

Storage Canopy

Storage Canopy C4040S User manual

Storage Canopy

Storage Canopy C3340R User manual

Storage Canopy

Storage Canopy FB408021DP User manual

Storage Canopy

Storage Canopy FB335017P User manual

Storage Canopy

Storage Canopy C4040R User manual

Storage Canopy

Storage Canopy C2640R User manual

Storage Canopy

Storage Canopy C2620R User manual

Storage Canopy

Storage Canopy C4040DTR User manual

Storage Canopy

Storage Canopy 33x40x12 User manual

Storage Canopy

Storage Canopy 40x80x15 User manual

Storage Canopy

Storage Canopy C2620 User manual

Storage Canopy

Storage Canopy C604015S User manual

Storage Canopy

Storage Canopy FB406021P User manual

Storage Canopy

Storage Canopy EWC6040DTR User manual

Storage Canopy

Storage Canopy C3340S User manual

Storage Canopy

Storage Canopy FB406021DP User manual

Storage Canopy

Storage Canopy C4060R User manual

Storage Canopy

Storage Canopy C6040S User manual

Storage Canopy

Storage Canopy DT Container shelter User manual

Storage Canopy

Storage Canopy C4020 User manual

Storage Canopy

Storage Canopy C4080S User manual

Storage Canopy

Storage Canopy 26x40x10 Container Shelter Single truss User manual

Storage Canopy

Storage Canopy 40x40x15 User manual

Popular Shelter manuals by other brands

Tempo Fitness

Tempo Fitness S11 manual

Tuindeco

Tuindeco 42.7906 Assembly instructions

No Butts Bin

No Butts Bin SR1605 Assembly instructions

TMG

TMG TMG-DT5040CG product manual

TMG

TMG TMG-DT3063-PRO product manual

EAGLE CLAW

EAGLE CLAW Shappell DX4000 manual

Kampa

Kampa Poled Shelter 300 Installation and operating manual

Harnois

Harnois TA-R Assembly

Shelters4Less

Shelters4Less SR1551 Assembly instructions

TMG

TMG TMG-DT50FW8 product manual

Vikre Handel AS

Vikre Handel AS JIT-1216 Assembly manual

VARNA buildings

VARNA buildings C2020H instruction manual

Frabill

Frabill ICE HUNTER 195 instruction manual

Shelters4Less

Shelters4Less SR1588 Assembly instructions

Sealey

Sealey Power Products GSS150819SD instructions

Crivit

Crivit 104155 Operation and safety notes

No Butts Bin

No Butts Bin SR1558-F Assembly instructions

TMG

TMG TMG-ST3040C product manual