StarTech.com SV231DVIUAHR User manual

Manual Revision: 08/12/2011

DE: Bedienungsanleitung - de.startech.com

FR: Guide de l'utilisateur - fr.startech.com

ES: Guía del usuario - es.startech.com

IT: Guida per l'uso - it.startech.com

NL: Gebruiksaanwijzing - nl.startech.com

PT: Guia do usuário - pt.startech.com

For the most up-to-date information, please visit: www.startech.com

SV231DVIUAHR

2 Port High Resolution Dual Link DVI

USB KVM Switch with Audio

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment

o and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit dierent from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected

names and/or symbols of third-party companies not related in any way to StarTech.com.

Where they occur these references are for illustrative purposes only and do not represent an

endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to

which this manual applies by the third-party company in question. Regardless of any direct

acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges

that all trademarks, registered trademarks, service marks, and other protected names and/or

symbols contained in this manual and related documents are the property of their respective

holders.

Instruction Manual i

Table of Contents

Introduction........................................................................................................................................................1

Packaging Contents ................................................................................................................................1

System Requirements ............................................................................................................................1

Installation............................................................................................................................................................2

Front View......................................................................................................................................................3

Rear View........................................................................................................................................................3

Operation .............................................................................................................................................................5

Front Panel ....................................................................................................................................................5

HotKey Control...........................................................................................................................................5

Alternative Hotkey Commands........................................................................................................5

Change Leading Hotkey.......................................................................................................................7

Specications.....................................................................................................................................................8

Technical Support ...........................................................................................................................................9

Warranty Information....................................................................................................................................9

Instruction Manual 1

Introduction

The SV231DVIUAHR 2-Port High Resolution Dual-Link DVI USB KVM Switch provides simple, yet

comprehensive control of 2 directly-connected computers, as well as audio switching capability

and support for high resolution applications (supports resolutions beyond 1080p: 2560x1600 @

60Hz, up to 3840 x 2400 at lower refresh rates, and Apple Cinema quality resolutions), oering a

superior KVM switching solution that integrates perfectly into demanding imaging, medical, and

multimedia environments.

This 2-port DVI USB KVM Switch is compatible with all USB-supported operating systems, and

features a built-in USB 2.0 hub that allows you to share additional (up to 2) high speed USB

devices between computers.

Packaging Contents

• 1 x KVM Switch

• 1 x Instruction Manual

• 1 x Rubber Foot Pad set

• 1 x Universal Power Adapter

System Requirements

• DVI-D enabled display device (i.e. monitor, projector, HDTV, etc.)

• DVI-D and USB enabled computer system

• A standard 104-key wired USB keyboard

• A standard 3-button wired USB mouse

Instruction Manual 2

Installation

NOTE: Prior to the installation, please power o all devices that will be connected to this system.

Ensure that all devices you will connect are properly grounded.

Place cables away from uorescent lights, air conditioners, and machines that are likely to

generate electrical noise.

If you experience any problems using a USB KVM switch, the following BIOS setup changes may

be necessary for PC users and not necessary for Mac users:

• Set HALT ON ERROR to ALL BUT KEYBOARD.

• In PNP AND PCI SETUP, set PNP OS INSTALLED to YES and set USB IRQ to ENABLED.

Dierent systems may use dierent naming, so contact your system manufacturer for further

assistance with these settings.

Instruction Manual 3

Front View

Rear View

Instruction Manual 4

Console Connection

Before installation, ensure that all devices and computers to be connected to the KVM switch are

powered o.

1. Connect a DVI-capable monitor to the Console’s DVI port.

2. Plug a USB keyboard and a USB mouse to any two of the Console’s USB ports as shown below.

Computer Connection

1. Use a male-to-male cable to connect from a computer’s DVI port to the KVM switch’s DVI port

of PC side, as shown below.

2. Use a USB A-B Cable to connect from the KVM switch’s USB port (B connector, square

connector) to the USB port on the corresponding computer (A connector, at connector), as

shown below.

Instruction Manual 5

Operation

Front Panel

On-line LED / Selected LED

When the LED turns green, the connected computer is powered-on. When a computer is

selected, its corresponding red LED illuminates.

Push Buttons

Pressing the “Select” button switches between ports.

HotKey Control

A Hotkey command is a short keyboard sequence for selecting a computer, activating computer

scan, etc. A hotkey sequence starts with two left <CTRL> keystrokes (successively within 0.2

seconds) followed by one or two more keystrokes. A built-in tone generator creates a high-pitch

beep for correct hotkey command; otherwise, one low-pitch beep is generated for errors and the

bad key sequence will not be forwarded to the selected computer.

NOTE: Press and hold Left <SHIFT> and press <NumLock> twice, then release <SHIFT> followed

by pressing left <CTRL> once, which will enable / disable the hotkey feature.

To select a computer:

Left <CTRL> + Left <CTRL> + <1>

(Example: Selects the computer at port 1.)

Left <CTRL> + Left <CTRL> + <2>

(Example: Selects the computer at port 2.)

NOTE: Do not use the keypad on the right-side of the keyboard.

Auto Scan

The KVM automatically scans through the powered-on computers in sequence on a xed time

interval (see Scan Time below).

Instruction Manual 6

To start Auto Scan:

Left <CTRL> + Left <CTRL> + <F1>

To abort the Auto Scan mode, press the left <CTRL> key twice. When Auto Scan detects any

keyboard activity, it suspends the scanning till the activity stops; it then resumes with the next

computer in sequence. The length of the Auto Scan interval (Scan Time) is adjustable, see below.

Manual Scan allows users to manually switch back and forth between powered-on computers.

Left <CTRL> + Left <CTRL> + <F2>

To select the previous or the next computer, press <UP> or <DOWN> arrow keys. To abort the

Manual Scan, press any other key.

Scan Time

Four options are available for users to set the Scan Time duration, it Includes 3, 8, 15 and 30

seconds.

Note: Scan Time is set to 3 seconds by default.

To adjust Scan Rate, set the scan time of duration before switching to the next computer:

Left <CTRL> + Left <CTRL> + <F3>

The KVM Switch generates 1 to 4 beeps indicating a scan time duration for 3, 8, 15 or 30 seconds

respectively.

Audio Lock

There are two options for Audio Lock: ON and OFF.

When ON, audio selection follows computer selection. When OFF, audio selection stops

following computer selection. It is useful if you want to listen to a particular computer’s audio

signal while operating other computers.

Left <CTRL> + Left <CTRL> + <F5>

The KVM switch beeps once or twice corresponding to ON and OFF respectively.

To change which computer port the audio stays on to the currently selected port, press the

following hotkey:

Left <CTRL> + Left <CTRL> + <A>

Instruction Manual 7

USB-Port Rule

There are two settings for USB-Port Rule: ON or OFF.

When set to ‘ON’, the USB Hub ports follows computer selection.

When set to ‘OFF’, the USB Hub ports stays on the currently selected PC port.

Press the hotkey below to turn ON/OFF the USB-Port Rule:

Left <CTRL> + Left <CTRL> + <F7>

To change the PC port that the USB hub stays on to the currently selected PC port, press the

following hotkey:

Left <CTRL> + Left <CTRL> + <U>

NOTE: Please make sure that installation of the USB device has been accomplished before

switching to the next computer.

Change Leading Hotkey

The default leading hotkey sequence involves pressing the left <CTRL> twice in succession

(e.g. left <CTRL> + left <CTRL>). This can be changed to the right <CTRL> key instead, to avoid

accidental activation due to using the left <CTRL> key for functions such as Copy/Paste.

To change the leading hotkey sequence to Right <CTRL>:

Left <CTRL> + Left <CTRL> + hold <ALT> + press Right <CTRL>

All hotkey commands that previously required pressing the Left <CTRL> will be switched to

requiring the right <CTRL> instead.

To change the leading hotkey sequence back to Left <CTRL>:

Right <CTRL> + Right <CTRL> + hold <ALT> + press Left <CTRL>

Table of contents

Other StarTech.com Switch manuals

StarTech.com

StarTech.com MSTCDP122HD User manual

StarTech.com

StarTech.com SV231USBA User manual

StarTech.com

StarTech.com 5G7AINDRM-USB-A-HUB User manual

StarTech.com

StarTech.com ENTERPRISE CLASS SV1653DXI User manual

StarTech.com

StarTech.com SV211KDVI User manual

StarTech.com

StarTech.com StarView SV431H User manual

StarTech.com

StarTech.com IESC1G50UP User manual

StarTech.com

StarTech.com HB30A3A1CST User manual

StarTech.com

StarTech.com 2PORT-HDMI-SWITCH-8K User manual

StarTech.com

StarTech.com SV231HDMIUA User manual

StarTech.com

StarTech.com SV231DPUA User manual

StarTech.com

StarTech.com IES81GW Guide

StarTech.com

StarTech.com SV831DUSBUK User manual

StarTech.com

StarTech.com HB30C3AGEPD User manual

StarTech.com

StarTech.com SV431DPUA2 User manual

StarTech.com

StarTech.com IES101G2SFPW User manual

StarTech.com

StarTech.com StarView SV221DVI Manual

StarTech.com

StarTech.com 35BAYFWUSB System manual

StarTech.com

StarTech.com SV431USBDDM User manual

StarTech.com

StarTech.com VS410DVIR User manual

StarTech.com

StarTech.com SV431HDU3A2 User manual

StarTech.com

StarTech.com C2-D46-UAC-CBL-KVM User manual

StarTech.com

StarTech.com VS221HD2VGA User manual

StarTech.com

StarTech.com SV431DPUA User manual

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual