StarTech.com ET1110PSE User manual
Manual Revision: 07/25/2012
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
ET1110PSE
PSE / PoE Gigabit Fiber Power over
Ethernet Media Converter - Open SFP
*actual product may vary from photos
Instruction Manual
2
Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.
Instruction Manual
i
Table of Contents
Introduction ............................................................................................1
Packaging Contents ................................................................................................................................. 1
System Requirements .............................................................................................................................. 1
Installation ..............................................................................................2
Software Installation ................................................................................................................................ 3
Conguration Diagram ........................................................................................................................... 4
Operation ................................................................................................5
Front Panel Pushbuttons ........................................................................................................................ 5
Keyboard Hotkeys ..................................................................................................................................... 5
KVM Switcher Software ........................................................................................................................... 6
Specications ..........................................................................................9
Technical Support ..................................................................................10
Warranty Information ............................................................................10
Instruction Manual
1
Introduction
The ET1110PSE PSE / PoE Gigabit Fiber Power over Ethernet Media Converter
with Open SFP creates an Ethernet-Fiber link, transparently converting from
10/100/1000Base-T copper to 1000Base-SX/LX ber, while acting as a Power Sourcing
Equipment (PSE) device. The PoE media converter oers the added exibility of an
open SFP slot, allowing you to choose the gigabit SFP that best suits your network
requirements for ber connection type and distance - see full line of compatible
Gigabit transceivers for this product at StarTech.com Accessories.
The open SFP media converter is capable of delivering up to 48V DC power to IEEE
802.3af devices such as wireless access points (WAP) or IP cameras, using standard Cat
5 (or better) cabling - an ideal solution for providing data and power to areas where
electrical wall outlets may not be available, saving the hassle and expense of running
new electrical wiring.
Backed by a StarTech.com 2-year warranty and free lifetime technical support.
Packaging Contents
• 1 x PSE/PoE Fiber Media Converter
• 1 x Universal Power Adapter (NA/EU/UK)
• 1 x Instruction Manual
System Requirements
• Fiber, Gigabit, or 10/100 Mbps compatible network
Instruction Manual
2
LED Indicators
PWR
PSE
FX LNK
100/1000
FULL
UTP LNK
LED Function State Status
PWR Converter
Power
ON Power on
OFF Power o
PSE PSE Status ON PSE power in-use
OFF PSE standby
FX LNK Fiber link
Status
ON Fiber link is ok
OFF No Fiber link
100/1000 LAN Speed
Status
Orange 1000Mbps
Green 100Mbps
OFF 10Mbps
FULL LAN Duplex
mode
ON Full duplex
OFF Half duplex
UTP LNK UTP link
status
ON UTP link is ok
OFF No UTP link
Instruction Manual
3
DIP Switch Setting
The ET1110PSE is provisioned through the use of a single 4‐pole DIP (Dual Inline
Package) switch located on the front panel. Setting a switch down places it in
the ON position.
Switches 1&2: provide setting auto‐negotiation (Nway) or manual forced speed of 10,
100 or 1000. Default is all OFF.
Switch 3: when ON (down), sets the forced Half Duplex for either 10Base or 100Base, or
sets Full Duplex when OFF (up).
Switch 4: is used to enable the LFP (Link Fault Pass‐Thru) function. LFP is enabled
when the switch is ON (down).
DIP Setting
ON “ “
OFF “ “ 1 2 3 4
UTP/NWAY
I
G
N
O
R
E
1000/FULL
100/FULL
100/HALF
10/FULL
10/HALF
LFP ON IGNORE
123 4 ON
Instruction Manual
4
Installation
1. Insert a compatible SFP Gigabit module into the open SFP slot
2. Connect the power supply to the Fiber Media Converter
3. Connect the appropriately terminated Fiber cable to the Fiber Tx/Rx port
4. Connect the other end of the ber cable into the router/switch/computer NIC/
another media converter (Remember to reverse the TX and RX leads between the
two devices)
5. Connect an Ethernet patch cable to the Fiber Media Converter “LAN”port
6. Connect the other end of the Ethernet patch cable to your endpoint device
Link-Fault-Pass Through (LFP) Note
This media converter incorporates a ber link pass through feature which allows
indirect sensing of a ber link loss via 10/100/1000 Base‐TX UTP connection. Whenever
the media converter detects a link loss condition on the receive ber (FX LNK O),
it disables its UTP transmitter so that a link loss condition is sensed on the receive
UTP port. (See the following gure) The link loss can then be sensed and reported by
network management agent at the remote UTP port’s host equipment.
The LFP feature has no eect on the media converter’s UTP Link LED, which continues
to function normally, independent of the state of the ber LNK LED and the UTP
transmitter. This feature is disabled by default from the factory.
UTP UTP
Link Link
Fiber
Remote Fault
Switch
or PC
Switch
or PC
TX (OFF)
RX (OFF)
Figure: Fiber Break Responses
Fail Fail
TX
RX
TX RX
RX TX
Instruction Manual
5
Specications
Connectors
1 x RJ45 Ethernet
1 x SFP slot
1 x DC Jack power connector
Power Output 48V DC @ 15.4W Supported
Transmission Standards
IEEE802.3 10BASE-T
IEEE802.3u 100BASE-TX
IEEE802.3ab 1000BASE-T
IEEE802.3z 1000BASE-SX
IEEE802.3af PoE
IEEE802.3x Flow Control
Duplex Modes Full/Half Duplex Ethernet mode
Dimensions 145mm x 65mm x 35mm
Weight 600g
Note
Fiber data transfer speeds and distances
are dependant on the SFP used
(sold seperately)
Instruction Manual
6
Other manuals for ET1110PSE
1
Table of contents
Other StarTech.com Media Converter manuals
StarTech.com
StarTech.com VGA2TV2WAY Manual
StarTech.com
StarTech.com POESLT1G48V User manual
StarTech.com
StarTech.com MCM1110SFP User manual
StarTech.com
StarTech.com ICUSBAUDIO System manual
StarTech.com
StarTech.com ET1000S40LC2 User manual
StarTech.com
StarTech.com VID2HDMITV Owner's manual
StarTech.com
StarTech.com HDMI2VGA User manual
StarTech.com
StarTech.com ET1000SM40LC System manual
StarTech.com
StarTech.com ST122LEA User manual
StarTech.com
StarTech.com PIB2MS1 User manual
StarTech.com
StarTech.com IDE2SAT25 User manual
StarTech.com
StarTech.com ET90110WDM System manual
StarTech.com
StarTech.com CPNT2VGAA User manual
StarTech.com
StarTech.com ET91000SC2 User manual
StarTech.com
StarTech.com DVI2HDMIA User manual
StarTech.com
StarTech.com ET91000LCOAM User manual
StarTech.com
StarTech.com 25SAT22MSAT User manual
StarTech.com
StarTech.com MDP2DVID User manual
StarTech.com
StarTech.com SPDIF2AA User manual
StarTech.com
StarTech.com ET90110SC2 User manual
