StarTech.com STDHVHDBT User manual

Manual Revision: 02/01/2017

For the latest information, technical specications, and support

for

this product, please visit www.startech.com/STDHVHDBT.

FR: Guide de l’utilisateur - fr.startech.com

DE: Bedienungsanleitung - de.startech.com

ES: Guía del usuario - es.startech.com

NL: Gebruiksaanwijzing - nl.startech.com

PT: Guia do usuário - pt.startech.com

IT: Guida per l’uso - it.startech.com

STDHVHDBT

Multi-Input HDBaseT Extender - 230 ft

*actual product may vary from

Instruction manual

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses and can radiate radio frequency energy and,

if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

Changes or modications not expressly approved by StarTech.com could void the user’s

authority to operate the equipment.

Industry Canada Statement

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [A] est conforme à la norme NMB-003 du Canada.

CAN ICES-3 (A)/NMB-3(A)

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other

protected names and/or symbols of third-party companies not related in any way to

StarTech.com. Where they occur these references are for illustrative purposes only and do not

represent an endorsement of a product or service by StarTech.com, or an endorsement of the

product(s) to which this manual applies by the third-party company in question. Regardless

of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby

acknowledges that all trademarks, registered trademarks, service marks, and other protected

names and/or symbols contained in this manual and related documents are the property of

their respective holders.

Instruction manual

Table of Contents

Transmitter diagram.......................................................................................... 1

Front view .................................................................................................................................................... 1

Rear view...................................................................................................................................................... 1

Receiver diagram................................................................................................ 2

Front view .................................................................................................................................................... 2

Rear view...................................................................................................................................................... 2

Introduction......................................................................................................... 3

Package contents...................................................................................................................................... 3

Requirements ............................................................................................................................................. 3

Preparing your site............................................................................................. 4

Installation............................................................................................................ 4

Operation.............................................................................................................. 5

Mode selection and switch operation............................................................................................... 5

VGA screen shifting.................................................................................................................................. 6

Set EDID........................................................................................................................................................ 7

Manual operation with serial control................................................................................................. 8

LED indicators .................................................................................................... 12

Technical support............................................................................................... 14

Warranty information ....................................................................................... 14

Instruction manual

1. Selected port LEDs

2. Input selection buttons

3. IR sensor

Rear view

4. Function buttons

5. Remote output LED

6. Local output LED

7. Output buttons

Front view

Transmitter diagram

1. DC 12V power port

2. (Control) RJ11 serial jack

3. IR Out/In ports (not active)

4. HDMI output port

5. HDBaseT output port

6. Audio In 3.5mm port (for VGA)

7. VGA input port

8. DP input port

9. HDMI 1 input port

10. HDMI 2 input port

11. Mode switch

12. Auto Inventory EDID switch

13. EDID COPY button

13 678

910

Instruction Manual

1. HDMI output

2. Status LED

1. DC power port

2. HDBaseT input port

3. Grounding bolt

Receiver diagram

Front view

Rear view

Instruction manual

Introduction

Package contents

• 1 x multi-input HDBaseT extender switch (transmitter)

• 1 x HDBaseT receiver

• 1 x IR remote control

• 1 x universal power adapter (NA, EU, UK, ANZ)

• 2 x mounting brackets

• 1 x RJ11-to-RS232 converter

• 1 x 5 ft [1.5 m] RJ11 cable

• 1 x 4 ft [1.2 m] RJ45 cable

• 8 x foot pads

• 1 x screw kit

• 1 x quick-start guide

Requirements

• Two HDMI video sources with cabling.

• One DisplayPort video source with cabling.

• One VGA video source with cabling.

• One remote HDMI display with cabling.

• A length of CAT5e or CAT6 cable running the distance between your transmitter and

receiver.

• One local HDMI display with cabling (optional).

Instruction manual

Preparing your site

1. Set up your local HDMI, DisplayPort and VGA video sources in your desired local

location.

2. Set up your remote display in your desired location.

Notes:

• Ensure that the transmitter and receiver are located near an AC power outlet.

• Ensure all devices are powered o.

Installation

1. Connect each of your video sources to the input ports on the transmitter, using the

required cabling (not included).

2. (Optional for local video output) connect an HDMI cable (not included) to your local

HDMI display and to the transmitter’s HDMI output port.

3. Connect the power adapter port on the extender switch to your AC outlet using the

power adapter, and press the power button to power on the extender switch.

4. Connect an RJ45 terminated CAT5e or CAT6 cable to the HDBaseT output on the

extender switch and to the HDBaseT input port on the receiver.

Important Notes:

• Use only the receivers included with this kit. The included HDBaseT receivers

use 12V POC, mixing hardware with a dierent HDBaseT kit can damage your

equipment.

• Do not route the cable through any networking equipment.

5. Power up each of your devices. The image from your video source will now appear

on your remote display (and local display, if connected in step 2).

6. (Optional for serial control) connect the RJ11 cable (included) to the (Control) RJ11

serial jack on the extender switch and to the RJ11-to-RS232 serial converter. Then

connect a 9-pin serial cable (not included) to the RJ11-to-RS232 converter and to

9-pin serial connector on your computer.

Note: The resolution performance of this extender switch will vary depending on the

length of your cabling. Please review the chart below to determine the best solution

for your setup. For best results, StarTech.com recommends shielded CAT6 cable.

Distance Maximum resolution

35 m (115 ft.) or less 4K x 2K at 30 Hz

Up to 70 m (230 ft.) 1080p at 60 Hz

Instruction Manual

Operation

Mode selection and switch operation

This HDBaseT switch features multiple operating modes. Review the description and

operating steps for each mode in this section, then use the Mode switch to the set the

HDBaseT switch to your desired operating mode.

Switch mode operation (1. Switch)

Switch mode enables you to switch between video sources by pressing the Input

selection button that corresponds with your desired video source. The active selected

port LEDs will light up indicating which port is selected.

Automatic mode operation (2. Auto)

Automatic mode enables the video converter switch to automatically select the most

recently activated or connected video source. Connect a new device or turn on an

already connected device to automatically switch video sources. The active selected

port LEDs will light up indicating which port is selected.

Priority-A mode operation (3. Pri-A)

Priority-A mode prioritizes the HDMI #1, DisplayPort, VGA, and HDMI #2 input ports

respectively. When you turn on a video source that is connected to a higher prioritized

input port, that video source will automatically be selected. Turning o the device will

automatically switch back to the lower prioritized video source.

Priority B mode operation (4. Pri-B)

Priority B mode prioritizes the HDMI #2, VGA, DisplayPort, and HDMI #1 input ports

respectively. When you turn on a video source that is connected to a higher prioritized

input port, that video source will automatically be selected. Turning o the device will

automatically switch back to the lower prioritized video source.

Instruction Manual

Manual operation with remote control

1. Press buttons 1 through 4 on the right side of the IR remote control to switch

between the HDMI #1, HDMI#2, DisplayPort, and VGA ports respectively.

2. The active selected port LEDs will light up on the extender switch, indicating

which port is selected, and your desired video source will appear on the HDMI and

HDBaseT displays.

VGA screen shifting

Screen shifting can move alignment of the VGA video output to the right or left of the

monitor, depending upon your requirements.

1. Press and hold both of the Function buttons (Function+VGA) simultaneously for 2

seconds until the VGA input LED turns blue and ashes orange.

2. Press the left Function button (VGA) or right Function button to move the screen

right and left respectively, depending upon your desired screen position.

Notes:

• The VGA port is the only video output that’s aected.

• The switch will exit VGA screen shifting mode after being inactive for 20 seconds.

• The maximum number of adjustments is 50 steps (right and left in total).

• The switch will automatically retain your most recent setting.

Instruction Manual

Set EDID

When a video source is connected to a display, the display’s EDID is communicated to

the video source. The display’s EDID is comprised of it’s video and audio capabilities.

Displays sharing their EDID ensures optimal performance, by enabling the source to

automatically align it’s video and audio settings to your display. Improper EDID can

cause issues with your display.

As this switch enables you to connect two displays (one local, one remote) to your

video sources, it’s possible that each display will have a variance of audio and video

capabilities.

To ensure optimal performance across both displays, this HDBaseT switch features

EDID emulation and EDID copy. These features enable you choose which settings will

best harmonize across both of your displays, to ensure optimal performance. Follow

the below steps to emulate and/or copy EDID audio and video.

1. Determine whether your ideal setup will be based on emulating 1080p video and

2-channel audio across both displays, or sharing one of the displays video and/or

audio capabilities across each attached display.

Note: You can copy EDID from either your local or remote display. However, you

cannot copy audio from one and video from the other.

2. Set the Auto Inventory EDID switch to your desired setting based on your

determination in step 1.

The Auto Inventory EDID switch lets you set whether you emulate (Auto) or copy

(Inventory) your EDID settings.

Review the table below to determine what the switch should be set to.

3. If you intend to copy EDID from your remote display, press and hold the EDID

copy button for three seconds until the Remote LED ashes GREEN.

If you intend to copy EDID from your local display, press and hold the EDID copy

button for six seconds until the Local LED ashes Green.

Position Video Audio EDID Status

1Emulate (1080p) Emulate (2-CH) Emulates video and audio

2Emulate (1080p) Copy Emulates video and copies audio

3Copy Emulate (2-CH) Copies video and emulates audio

4Copy Copy Copies video and audio

Other manuals for STDHVHDBT

Table of contents

Other StarTech.com Extender manuals

StarTech.com

StarTech.com ST121UTP User manual

StarTech.com

StarTech.com EOC110K System manual

StarTech.com

StarTech.com USBthere USB204EXT User manual

StarTech.com

StarTech.com USB2G4LEXT2 User manual

StarTech.com

StarTech.com SV565UTPDUV User manual

StarTech.com

StarTech.com SV565UTPUSA User manual

StarTech.com

StarTech.com USBthere USB201EXT User manual

StarTech.com

StarTech.com ST121UTP23GB User manual

StarTech.com

StarTech.com ST124HDBT User manual

StarTech.com

StarTech.com USBthere USB120EXT User manual

StarTech.com

StarTech.com IPUSB2HD2 User manual

StarTech.com

StarTech.com ST121HDFXA User manual

StarTech.com

StarTech.com ST121UTP User manual

StarTech.com

StarTech.com USB2004EXTGB User manual

StarTech.com

StarTech.com ST12MHDLAN4K User manual

StarTech.com

StarTech.com VS321HDBTK User manual

StarTech.com

StarTech.com USBthere USB201EXT User manual

StarTech.com

StarTech.com SV565UTP User manual

StarTech.com

StarTech.com SVA12M5NA User manual

StarTech.com

StarTech.com SV565UTPUL User manual

StarTech.com

StarTech.com POEEXT1GAT User manual

StarTech.com

StarTech.com ST121HDBTE User manual

StarTech.com

StarTech.com USB110EXT2 User manual

StarTech.com

StarTech.com USB110EXT2 User manual

Popular Extender manuals by other brands

SY HDBT-60T installation guide

Appsys ProAudio

Appsys ProAudio ADX-16 user manual

Atlona

Atlona RS232 user manual

IDK

IDK OPF-TH1000-A user guide

Enable-IT

Enable-IT 824WP quick start guide

Worx

Worx Landroid RadioLink WA0864 Get started

TP-Link

TP-Link TL-WA730RE user guide

Camplex

Camplex CMX-HDMI-SFPL user manual

SC&T

SC&T HE03-4K user manual

Marmitek

Marmitek MegaView70 user manual

Samsung

Samsung SCS-26UC4 user guide

Foxun

Foxun SX-GES24 operating instructions

MuxLab

MuxLab 500771 Operation manual

foxunhd

foxunhd SX-AEX01 operating instructions

TERK Technologies

TERK Technologies LFIRX2 owner's manual

Devolo

Devolo Audio Extender supplementary guide

Edimax

Edimax EW-7438RPn V2 instructions

Shinybow USA

Shinybow USA SB-6335T5 instruction manual