StarTech.com UNIDUPDOCK User manual
Hard Drive Docking Station
USB to IDE SATA Standalone
Hard Drive Duplicator Dock
UNIDUPDOCK
Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.•
Increase the separation between the equipment and receiver.•
Connect the equipment into an outlet on a circuit different from that to which the receiver•
is connected.
Consult the dealer or an experienced radio/TV technician for help.•
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an
endorsement of the product(s) to which this manual applies by the third-party company
in question. Regardless of any direct acknowledgement elsewhere in the body of
this document, StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this
manual and related documents are the property of their respective holders.
i
Table of Contents
Introduction..................................................................... 1
Packaging Contents.....................................................................1
System Requirements .................................................................1
Product View................................................................................2
Configuration Buttons..................................................................2
Installation....................................................................... 3
Hardware Installation...................................................................3
Driver Installation.........................................................................4
How to Use ...................................................................... 5
Menu Options ..............................................................................5
Duplicator (Copy) Mode...............................................................5
RAID Mode..................................................................................6
Available RAID Modes.................................................................6
RAID 1 Rebuild............................................................................7
Specifications.................................................................. 8
Technical Support........................................................... 9
Warranty Information...................................................... 9
1
Introduction
The UNIDUPDOCK functions as both a convenient hard drive copying/
imaging solution and an external USB to SATA/IDE HDD docking
station for 2.5” (up to 500Gb) or 3.5” hard drives (up to 2 TB).
Packaging Contents
1 x UNIDUPDOCK duplicator dock•
1 x USB cable•
2 x 40-pin IDE ribbon cable (female/female)•
2 x LP4 molex adapter cable•
2 x 40 to 44-pin IDE adapter•
1 x Universal Power Adapter•
3 x Power Cords (NA/UK/EU)•
1 x Instruction Manual•
System Requirements
2.5” and/or 3.5” SATA and/or IDE hard drive(s)•
USB operation:• Microsoft Windows®2000/XP/Vista/7, Mac OS®X,
or Linux®
2
Power connector
ON/OFF switch
USB connector
7+15 SATA
connector
40-pin IDE
connector
LP4 molex
connector
Built-in LCD screen
Configuration
buttons
Conguration Buttons
Button Function
Navigate Up
Navigate Down
ENT Enter
ESC Cancel
RESET Reset duplicator dock (soft)
MUTE Mute buzzer sounds
Product View
3
Installation
WARNING: Hard drives require careful handling, especially when
being transported. If you are not careful with your hard disk, lost data
may result. Always handle your hard drive and storage device with
caution.
Hardware Installation
Plug the universal power adapter into a wall power outlet and into1.
the DC In connector on the duplicator dock.
If using a SATA hard drive as the source disk. gently slide the2.
hard drive into the 7+15 SATA connector labeled Source-1 on the
duplicator dock. Skip to step 6.
If using an IDE hard drive as the source disk, connect the IDE ribbon3.
cable (included) to the 40-pin connector labeled Source-2. The
connector is keyed to fit only one way.
Connect the LP4 molex cable (included) into the 4-pin connector4.
next to the 40-pin IDE connector. The connector is keyed to fit only
one way.
4
Connect the IDE hard drive to the ribbon cable and LP4 molex5.
connector. If connecting a 2.5” IDE hard drive, attach the 40 to
44-pin adapter to the end of the ribbon cable and LP4 cable, then
connect the hard drive to the adapter.
NOTE: Only one Source disk and one Destination disk can be installed
at a time. Only connect an SATA or an IDE hard drive, not both.
Follow the same procedure for either an SATA or IDE hard drive for6.
the Destination side of the duplicator dock.
NOTE: SATA and IDE hard drives can be mixed, so one side can be
SATA while the other is IDE.
Slide the power ON/OFF switch on the side of the unit to the ON7.
position, to power up the unit.
Once the unit has booted up, use the configuration buttons and built-8.
in LCD display to configure and operate the duplicator dock.
If using as an external hard drive dock, connect the USB cable from9.
the duplicator dock to the computer’s USB port.
Driver Installation
No driver installation is required for any supported operating system,
as this hard drive dock is natively supported, so the drivers are already
installed.
5
How to Use
Menu Options
Copy HDD
Perform a 1:1 sector clone from the Source disk to the Destination•
disk.
Compare HDD
Compares the sectors on the Source disk to the Destination disk.•
Used to ensure that the Copy operation was successful.
Pre-scan
Scans the Source disk for bad sectors.•
Erase
Erase all data/sectors on the Source disk.•
Rescan Bus
Rescans all the hard drive connectors on the duplicator dock.•
Source Size
Displays the capacity of the Source disk.•
Setup
System information and RAID mode setup.•
Duplicator (Copy) Mode
Use the <up> and <down> arrows on the duplicator dock to select
the Copy HDD mode and press the ENT button to activate. The LCD
screen will display transfer rates, progress percentage, amount of data
copied and a countdown timer.
NOTE: As the duplicator dock creates a 1:1 copy, the Destination disk
must be of equal or greater capacity than the Source disk.
6
RAID Mode
Use the <up> and <down> arrows to navigate to the Setup Mode and
press the ENT button. Navigate to the “Change RAID Mode” option
and press ENT.
NOTE: Changing the RAID mode may result in data loss, so make sure
all important data is backed up, before attempting to change the RAID
mode.
Available RAID Modes
Mode Function
Normal Two independent disks
RAID0
Striped drives for maximum data transfer
rates. Combined capacity will be double the
smallest drive. No redundancy/backup.
RAID1 Mirroring a single drive to create two exact
copies.
JBOD Concatenate two drives to create a single
large disk.
7
RAID 1 Rebuild
When operating in RAID1 mode, if one of the hard drives fails or is
removed, the duplicator dock will enter a failed state and a buzzer will
sound once per second.
Use the <up> and <down> arrows to display information on either
Drive1 (Source) or Drive2 (Destination).
Reconnect a hard drive to the appropriate Source of Destination side
and the duplicator dock will automatically prompt for a rebuild.
The progress of the rebuild will be displayed, including the transfer
speed, percentage complete and a countdown timer to completion.
Other manuals for UNIDUPDOCK
1
Table of contents
Other StarTech.com Docking Station manuals
StarTech.com
StarTech.com DKT31CHDVCM User manual
StarTech.com
StarTech.com SATDOCKU3S User manual
StarTech.com
StarTech.com SATHDDDOCKU2 User manual
StarTech.com
StarTech.com UNIDOCK3U User manual
StarTech.com
StarTech.com 129N-USBC-KVM-DOCK User manual
StarTech.com
StarTech.com SDOCK2ERU33 User manual
StarTech.com
StarTech.com Thunderbolt TB3CDOCKDP User manual
StarTech.com
StarTech.com USB3SMDOCKHV User manual
StarTech.com
StarTech.com SDOCK2U33V User manual
StarTech.com
StarTech.com SDOCK1EU3P2 User manual
StarTech.com
StarTech.com DK31C3HDPDUE User manual
StarTech.com
StarTech.com USB3SDOCKD User manual
StarTech.com
StarTech.com TB3DKM2HD User manual
StarTech.com
StarTech.com SDOCKU33BV User manual
StarTech.com
StarTech.com 116N-USBC-DOCK User manual
StarTech.com
StarTech.com USB7N1DOCKGB User manual
StarTech.com
StarTech.com SATDOCKCRH User manual
StarTech.com
StarTech.com Thunderbolt TB3CDOCKDP User manual
StarTech.com
StarTech.com DKM30CHDPD User manual
StarTech.com
StarTech.com USB6N1DOCK Manual
