Spectra Logic Spectra 64K Manual
Entry/Exit Port Slider
Replacement Guide
•Spectra
®12K Library
•Spectra
®64KLibrary
2
Notices
Spectra Logic® Corporation provides the unit “as is” without warranty of any kind, either
expressed or implied, including but not limited to the implied warranties of merchantability or
fitness for a particular purpose. In no event shall Spectra Logic be liable for any loss of profits,
loss of business, loss of use or data, interruption of business, or for indirect, special, incidental,
or consequential damages of any kind, even if Spectra Logic has been advised of the possibility of
such damages arising from any defect or error.
Information furnished in this manual is believed to be accurate and reliable. However, no responsibility
is assumed by Spectra Logic for its use. Due to continuing research and development, Spectra Logic may
revise this publication from time to time without notice, and reserves the right to change any product
specification at any time without notice.
Entry/Exit Port Slider Replacement Guide: Spectra 12K and Spectra 64K libraries
Copyright ©2005 Spectra Logic Corporation. All rights reserved.
Spectra Logic Contact Information
Corporate Headquarters European Office
Address
Phone
Fax
Spectra Logic Corporation
1700 N 55th Street
Boulder CO 80301
USA
(800) 833-1132 or (303) 449-6400
(303) 939-8844
Address
Phone
Fax
Spectra Logic Europe Limited
Magdalen Centre
Robert Robinson Avenue
Oxford Science Park
Oxford
UK OX44 7 RW
+44 (0) 870 112 2150
+44 (0) 870 112 2175
Web Site http://www.SpectraLogic.com
Entry/Exit Port Slider Replacement Guide
3
Contents
Introduction ................................................................................................ 4
Prepare the Library and Host System ........................................................6
Remove the Robotic Rack Assembly .......................................................... 7
Remove the Spectra E/E Port Slider......................................................... 13
Replace the E/E Port Slider ...................................................................... 18
Replace the Robotic Rack Assembly ........................................................ 20
Prepare the Library for Tests.................................................................... 23
Tests .......................................................................................................... 24
Finish......................................................................................................... 27
Entry/Exit Port Slider Replacement Guide
4
Introduction
About This Manual
This manual describes the procedure for replacing the entry/exit (E/E) port slider in
Spectra 12K and Spectra 64K libraries, and how to test the assembly after it has been
installed.
About the E/E Port Slider
The E/E port slider enables the E/E port to move in and out to load and unload tape
cartridges.
Estimated Time Required
This procedure should take approximately two hours.
Figure 1 The E/E port slider.
Entry/Exit Port Slider Replacement Guide
5
Materials Required
You will need an E/E port slider assembly from Spectra Logic or an authorized reseller:
• E/E port slider assembly, P.N. 90919043 (top) or
• E/E port slider assembly, P.N. 90910044 (bottom)
You will also need the following tools:
• A #1 Phillips screwdriver
• A #2 Phillips screwdriver
• A 3/32-inch hex wrench
• A 2.5-mm hex wrench
• A small flat head screwdriver
• A large flat head screwdriver
• A flashlight
• The library door key
• The key to the rear door of the library (Spectra 64K libraries only)
Entry/Exit Port Slider Replacement Guide
6
Prepare the Library and Host System
Shut down the library while keeping the host interface connected to the host system.
1. Disable any backup software that might try to access the library.
Warning: Electric shock inside the library can cause injury or death.
Disconnect AC power before opening the library door.
2. Turn off the power. The power switch is located at the rear of the library on the
lower left. (It is necessary to unlock and open the rear door of Spectra 64K
libraries.)
3. If necessary, move the library to a location where you have full access to the front
of the library.
Caution: The library is heavy. Get help when moving the library.
• The Spectra 12K library weighs approximately 175 lbs.
• The Spectra 64K library weighs approximately 880 lbs.
4. Remove the drives from the drive bay and set them aside in a safe place.
Note: It is not necessary to remove the media.
5. Use the library door key to unlock the front door of the library. You can now open
the door.
Entry/Exit Port Slider Replacement Guide
8
2. Rotate the picker so that the bar code scanner faces the rear of the library.
The location of the bar code scanner is shown in Figure 3.
3. Slide the picker along the transport tray to the front of the library (Figure 4).
Figure 3 The location of the bar code scanner.
Figure 4 The picker is slid to the front of the library.
Location of the
bar code scanner
Entry/Exit Port Slider Replacement Guide
9
4. Look at the bottom of the library where the drives are located. If there is a hinge
connecting the left side of the drive slots to the back of the library (Figure 5),
proceed to Step 5.
If your library does not have a hinge (Figure 6), proceed to Step 6.
5. Using the appropriate screwdriver, loosen the screws just enough to move the gate
out of the way from the robotic rack assembly (Figure 7).
• Some Spectra 12K libraries have three screws in the gate, and some units will
not have any screws in the gate.
• The Spectra 64K library has five screws in the gate.
Figure 5 A library with a hinge. Figure 6 A library without a hinge.
Figure 7 The drive slot gate (Spectra 64K library shown).
Entry/Exit Port Slider Replacement Guide
10
6. Unplug the 25-wire black connector at the bottom front of the robotic rack
assembly (Figure 8).
7. Using the #2 Phillips screwdriver, loosen the screws that hold the robotic rack
assembly to the chassis: first the top three screws, then the bottom two (Figure 9).
Figure 8 The 25-wire black connector (Spectra 12K library
shown).
Figure 9 The robotic rack with the screws circled
(Spectra 12K library shown). On a 64K library, the
screws will be in the same pattern.
Other manuals for Spectra 64K
3
This manual suits for next models
3
Table of contents
Other Spectra Logic Storage manuals
Spectra Logic
Spectra Logic Spectra RXT150 User manual
Spectra Logic
Spectra Logic Spectra 20K User manual
Spectra Logic
Spectra Logic T-Series Spectra T50 User manual
Spectra Logic
Spectra Logic 10K Library Operating manual
Spectra Logic
Spectra Logic Spectra 10000 User manual
Spectra Logic
Spectra Logic Spectra 64K User manual
Spectra Logic
Spectra Logic Spectra nTier500 Instruction Manual
Spectra Logic
Spectra Logic 2007 User manual
Spectra Logic
Spectra Logic T-Series Spectra T200 User manual
Spectra Logic
Spectra Logic Spectra 2K Library User manual
Spectra Logic
Spectra Logic Spectra nTier700 User manual
Spectra Logic
Spectra Logic Spectra 12K Manual
Spectra Logic
Spectra Logic Spectra 12K Manual
Spectra Logic
Spectra Logic Spectra 64K Manual
Spectra Logic
Spectra Logic T-Series Spectra T50e User manual
Spectra Logic
Spectra Logic T-Series Spectra T200 User manual
Spectra Logic
Spectra Logic Spectra 10000 User manual
Spectra Logic
Spectra Logic T-Series Spectra T950 User manual
Spectra Logic
Spectra Logic Spectra 10K Manual
Spectra Logic
Spectra Logic Spectra 10K Instruction Manual
