Spectra Logic Spectra 10000 User manual
P.N.90840072RevisionE
Spectra4000-10000™Library
PowerSupplyReplacementGuide
Spectra4000-10000™LibraryPowerSupplyReplacementGuide
2
Notices
Spectra Logic Corporation provides the Spectra 10000 library “as is” without warranty of any
kind, either expressed or implied, including but not limited to the implied warranties of
merchantability or fitness for a particular purpose. In no event shall Spectra Logic be liable for
any loss of profits, loss of business, loss of use or data, interruption of business, or for indirect,
special, incidental, or consequential damages of any kind, even if Spectra Logic has been advised
of the possibility of such damages arising from any defect or error in this publication.
Information furnished in this manual is believed to be accurate and reliable. However, no responsibility
is assumed by Spectra Logic for its use. Due to continuing research and development, Spectra Logic may
revise this publication from time to time without notice, and reserves the right to change any product
specification at any time without notice.
Some products or services mentioned in this manual are provided by companies other than Spectra
Logic. Inquiries about one or more of these products or services should be sent directly to the company
in question.
ContactInformation
Support
(800)227-4637,(303)449-6444,extension3175
Sales
(800)833-1132,(303)449-6444
InternationalSales
011448701122150
Website
www.spectralogic.com
Spectra 10000 Library Power Supply Replacement Guide
Copyright © 2002 by Spectra Logic Corporation. All rights reserved.
Spectra4000-10000™LibraryPowerSupplyReplacementGuide
3
Contents
Introduction................................................................................................4
Prepare the Library.....................................................................................5
Remove the Power Supply..........................................................................6
Replace the Power Supply........................................................................12
Spectra4000-10000™LibraryPowerSupplyReplacementGuide
4
Introduction
AboutThisGuide
This manual describes the procedure for replacing the power supply assembly in
Spectra 4000-10000 tape libraries.
EstimatedTimeRequired
This procedure should take less than one hour.
MaterialsandToolsRequired
You will need a Power Supply Assembly Kit to install a new Power Supply into your
library. These kits are available from Spectra Logic, or an authorized Spectra Logic
reseller.
• Spectra 4000-9000 Power Supply Kit: P.N. 90841634
• Spectra 10000 Power Supply Kit: P.N. 92848069
You Will Also Need:
• A #1 Phillips screwdriver
• A #2 Phillips screwdriver
• A flat blade screwdriver
Spectra4000-10000™LibraryPowerSupplyReplacementGuide
5
PreparetheLibrary
1. Quit all programs and shut down your computer.
2. Turn off power to your computer.
3. Turn off power to your library. Switch off power to any other connected
equipment.
Warning: Shock hazard inside the library can cause injury or death.
Disconnect AC power to the library before removing the cover.
Never connect AC power to the library with the cover removed.
Caution: The power supply is a static sensitive device. Please use a static
dissipative wrist strap or other ESD equipment/tools for this
process.
4. Disconnect all cables from the library.
• Disconnect the AC power cord from the wall outlet and the rear of the library.
• Disconnect the SCSI cables from the rear of the library.
• If applicable, disconnect the serial cable(s) from the RS–232 port(s) on the rear of
the library.
5. Move the library to a location where you have access to all sides of the library.
Warning: The library is heavy, about 56 pounds (25.4 kilograms). Get help
when moving the library.
Spectra4000-10000™LibraryPowerSupplyReplacementGuide
6
RemovethePowerSupply
1. Use the appropriate screwdriver to completely remove the three library cover
screws on the rear of the library (Figure 1).
2. Slide the cover toward the rear of the library about one-half inch. This releases the
side clips holding the cover to the front panel (Figure 2).
3. Lift the cover straight up and off of the library (Figure 3).
4. Set the library’s cover off to the side and out of the way.
Figure1 Removethescrews.
Figure2 Slidecoverback. Figure3 Liftcoveroff.
Spectra4000-10000™LibraryPowerSupplyReplacementGuide
7
5. Use the appropriate screwdriver to remove the screws holding the rear panel of the
library in place (Figure 4 and Figure 5).
Note: If the library is rack mounted, the lower screws on each side are
not installed.
6. Lower the rear panel away from the library.
7. For SCSI units, disconnect the two yellow SCSI ribbon cables from the SDC board
(Figure 6) and the blue serial port cable from the UCM board (Figure 7).
Caution: Do not bend or put stress on the yellow SCSI ribbon cables.
Figure4 Screwsholdingtherearpanelinplace. Figure5 Detachtherearpanel.
Figure6 DisconnecttheSCSIribboncables. Figure7 Disconnecttheserialportcable.
Spectra4000-10000™LibraryPowerSupplyReplacementGuide
8
8. Disconnect the DC power plugs from the rear of each drive (Figure 8).
9. Detach the yellow SCSI ribbon cable from Drive 1.
10. Detach Drive 1’s nine-pin, rainbow-colored ID cable from the rear panel
(Figure 9).
11. Remove Drive 1 (Figure 10).
Figure8 Rearpanelloweredanddrivesunplugged.
Figure9 DetachDrive1’sIDcablefromtherear
panel. Figure10 Drive1removed.
Spectra4000-10000™LibraryPowerSupplyReplacementGuide
9
12. Disconnect the AC power switch cable at the connector located next to the rotary
motor (Figure 11).
Note: Check to see if the 13-pin power supply DC cable connection (red,
black and yellow wires) is located outside of the cage. If it is, go to
Step 17 on page 10, to complete the power supply removal.
If the 13-pin power supply DC cable connection (red, black and
yellow wires) is located inside of the cage, go to the next step.
13. Use the appropriate screwdriver to loosen the two captive screws that attach the
power supply bracket to the casting (Figure 12).
Figure11 Detachthepowerswitchcable.
Figure12 Loosenthetwocaptivescrews.
Spectra4000-10000™LibraryPowerSupplyReplacementGuide
10
14. Tilt the power supply toward the drives and remove the two screws on the back of
the power supply that hold the cage in place (Figure 13).
15. Turn the power supply upside down and remove the two screws on the bottom of
the power supply that hold the power supply cage in place (Figure 14).
16. Pull back the power supply cage (Figure 15).
17. Unplug the 13-pin power supply DC cable with red, black and yellow wires
(Figure 15 for SCSI; Figure 16 for Fibre Channel).
Figure13 Removethetwoscrewsonthebackofthe
powersupplythatholdthecageinplace. Figure14 Removethetwoscrewsonthebottomof
thepowersupplythatholdthecageinplace.
Figure15 Pullbackthepowersupplycageand
unplugtheSCSIunit’s13-pinDCcable. Figure16 UnplugtheFibreChannelunit’s13-pin
DCcable.
Other manuals for Spectra 10000
8
This manual suits for next models
2
Table of contents
Other Spectra Logic Storage manuals
Spectra Logic
Spectra Logic AIT-4 Manual
Spectra Logic
Spectra Logic Spectra 12K Manual
Spectra Logic
Spectra Logic Spectra nTier700 Instruction sheet
Spectra Logic
Spectra Logic Spectra 12K User manual
Spectra Logic
Spectra Logic T-Series Spectra T120 Instruction Manual
Spectra Logic
Spectra Logic Spectra nTier700 Instruction Manual
Spectra Logic
Spectra Logic T-Series Spectra T120 Operating manual
Spectra Logic
Spectra Logic Spectra 2000 Manual
Spectra Logic
Spectra Logic T-Series Spectra T120 User manual
Spectra Logic
Spectra Logic T-Series Spectra T950 Manual
Spectra Logic
Spectra Logic Spectra 2k Manual
Spectra Logic
Spectra Logic Spectra nTier500 User manual
Spectra Logic
Spectra Logic Spectra RXT Media User manual
Spectra Logic
Spectra Logic Spectra 10K Instruction Manual
Spectra Logic
Spectra Logic Spectra 10000 Instruction sheet
Spectra Logic
Spectra Logic Spectra nTier300 Instruction Manual
Spectra Logic
Spectra Logic T-Series Spectra T50e Parts list manual
Spectra Logic
Spectra Logic Spectra nTier300 User manual
Spectra Logic
Spectra Logic Spectra 20K User manual
Spectra Logic
Spectra Logic Spectra 2k AIT User manual
